Loop around (original) (raw)
A loop line or loop around is a telephone company test circuit. The circuit has two associated phone numbers. When one side of the loop is called (side A), the caller receives a test tone of approximately 1000 Hz (milliwatt test). When the second number (side B) is called, it produces dead silence, but the party on side A hears the milliwatt test tone drop, and is connected to the person on side B. The purpose of the loop around test is to allow circuit testing to a distant central office without needing a person at the far end. The technician can send a tone down either line and measure the response tone on the second line to determine the path loss parameters.
| Property | Value |
|---|---|
| dbo:abstract | A loop line or loop around is a telephone company test circuit. The circuit has two associated phone numbers. When one side of the loop is called (side A), the caller receives a test tone of approximately 1000 Hz (milliwatt test). When the second number (side B) is called, it produces dead silence, but the party on side A hears the milliwatt test tone drop, and is connected to the person on side B. The purpose of the loop around test is to allow circuit testing to a distant central office without needing a person at the far end. The technician can send a tone down either line and measure the response tone on the second line to determine the path loss parameters. When a line is connected to side A, multiple telephone lines, within limits, may connect to side B and thus be connected into a conference with the person on side A. The function of the tone on side A was to alert those already connected, when somebody called the B side and connected. Teenagers discovered that the test facility could be used as party lines, chat rooms or alternate phone number and would dial up the primary number and wait for someone at random to call its mate. Phreaks would use the loop around in a similar manner, to exchange information that they had learned about the phone company. Loop lines are far less common today than they were in the 1960s, however they reportedly continued to exist past the start of the 21st century. One such loop line is certain to exist: it is a TPI-560P located at (416) 981-0001 owned by Telus. It also comes with an automatic number announcement circuit. Because of the potential for abuse, however, telephone companies seek to protect them. The most common protection techniques are: * Filters that bandstop voice (these can be switched on or off) * Recordings which make the line appear out of service * Selective loop activation by operators * Restrictions on which lines may call * Using uncommon DTMF tones (A through D) in the telephone number Eventually, telephone companies designed devices to prevent this misuse of the loop around. Some devices blocked the audio if frequencies other than the milliwatt tone were present, which thwarted the average abuser, but skilled violators discovered that playing a 1000 Hz tone while speaking softly, the suppression unit could be subverted, and a notch filter could be used while listening to remove the tone at the other end. (en) |
| dbo:wikiPageID | 4436402 (xsd:integer) |
| dbo:wikiPageLength | 3025 (xsd:nonNegativeInteger) |
| dbo:wikiPageRevisionID | 821724668 (xsd:integer) |
| dbo:wikiPageWikiLink | dbc:Telephone_numbers dbr:Conference_call dbr:Milliwatt_test dbr:Loopback dbr:Party_line_(telephony) dbr:DTMF dbr:Band-stop_filter dbr:Chat_room dbr:Hertz dbc:Communication_circuits dbr:Automatic_number_announcement_circuit dbr:Path_loss dbr:Telephone_company dbr:Phreaks dbr:Notch_filter |
| dbp:wikiPageUsesTemplate | dbt:! dbt:Other_uses dbt:Refimprove dbt:Reflist |
| dcterms:subject | dbc:Telephone_numbers dbc:Communication_circuits |
| gold:hypernym | dbr:Circuit |
| rdf:type | dbo:BaseballLeague yago:WikicatCommunicationCircuits yago:Artifact100021939 yago:Circuit103033362 yago:Device103183080 yago:ElectricalDevice103269401 yago:Instrumentality103575240 yago:Object100002684 yago:PhysicalEntity100001930 yago:Whole100003553 |
| rdfs:comment | A loop line or loop around is a telephone company test circuit. The circuit has two associated phone numbers. When one side of the loop is called (side A), the caller receives a test tone of approximately 1000 Hz (milliwatt test). When the second number (side B) is called, it produces dead silence, but the party on side A hears the milliwatt test tone drop, and is connected to the person on side B. The purpose of the loop around test is to allow circuit testing to a distant central office without needing a person at the far end. The technician can send a tone down either line and measure the response tone on the second line to determine the path loss parameters. (en) |
| rdfs:label | Loop around (en) |
| owl:sameAs | freebase:Loop around yago-res:Loop around wikidata:Loop around https://global.dbpedia.org/id/4qjL2 |
| prov:wasDerivedFrom | wikipedia-en:Loop_around?oldid=821724668&ns=0 |
| foaf:isPrimaryTopicOf | wikipedia-en:Loop_around |
| is dbo:wikiPageWikiLink of | dbr:Masters_of_Deception dbr:Milliwatt_test dbr:Loopback dbr:Ringback_number dbr:Automatic_number_announcement_circuit dbr:Loop_line dbr:Plant_test_number |
| is foaf:primaryTopic of | wikipedia-en:Loop_around |