LCD Interfacing with ATmega32 AVR Microcontroller (original) (raw)

In this tutorial, we will discuss the LCD display and its interfacing with the ATmega32 AVR microcontroller. We will use the 8-bit mode to transfer data to the Display. We will also look at the basic difference between 8-bit mode and 4-bit mode. How do we write code for LCD interfacing in C, and what are the basic commands used for LCD programming? Here we will also learn how to program LCD and send commands or data to LCD.

What is LCD?

LCD, which stands for Liquid Crystal Display, is an electronic device that is used for data display. LCDs are preferable over seven segments and LEDs as they can easily represent data in the form of alphabets, characters, numbers, or animations. LCDs are very easy to program and make your work quite attractive and simple. Numerous types of LCDs are available on the market, such as 16X2, 16X4, 20X2, 20X4, graphical LCDs (128X64), etc. The LCD that we are using is a 16X2 alphanumeric LCD; it displays 32 characters in two rows, so in one row we have 16 characters.

Pin Description of LCD

16X2 LCDs can interface with AVR microcontrollers in two modes: 4-bit mode and 8-bit mode. In this article, we will use an 8-bit mode for interfacing. In 8-bit mode, we send commands to the LCD by using eight data lines (D0-D7), while in 4-bit mode, we use four data lines (D5-D7) for sending commands and data. These data lines can be connected to any port of the ATmega32.

How to Program LCD?

Basically, there are two registers: command and data. When we are giving commands to the LCD display, we select the command register, and when we are sending data to the display, we select the data register. A command is an instruction given to the display in order to perform the required function according to the given command. In order to display textual information, data is sent to the LCD display.

Sending Commands on LCD

For sending commands on LCD, we have to write commands on data pins. For this, select:

RS = 0 >> selects command register
RW = 0 >> selects write operation
E >> make enable pin from high to low

Sending Data on LCD

For sending data on LCD, we have to write data on data pins. For this, select:

RS = 1 >> selects data register
RW = 0 >> selects write operation
E >> make enable pin from high to low

Schematic Diagram

We designed our circuit on Proteus. A circuit diagram of 16×2 LCD with Atmega32 microcontroller is given below:

LCD interfacing with ATmega32 AVR MICROCONTROLLER

We use Atmel Studio 6 for the development of code, and the code is written in C.

#ifndef F_CPU
# define F_CPU 16000000 UL // clock speed is 16MHz
#endif

#include<avr/io.h> // AVR header
#include<util/delay.h> // delay header

//******************LCD PROGRAM STARTS*********************//

#define LCD_DATA PORTB // port B is selected as LCD data port
#define ctrl PORTD // port D is selected as LCD command port

#define en PD7 // enable signal is connected to port D pin 7
#define rw PD6 // read/write signal is connected to port D pin 6
#define rs PD5 // register select signal is connected to port D pin 5

void LCD_cmd(unsigned char cmd);
void init_LCD(void);
void LCD_write(unsigned char data);

int main(void)
{
  DDRB = 0xFF; // set LCD data port as output
  DDRD = 0xE0; // set LCD signals (RS, RW, E) as out put

  init_LCD(); // initialize LCD
  _delay_ms(100); // delay of 100 Milli seconds

  LCD_cmd(0x0C); // display on, cursor off
  _delay_ms(100);

  LCD_write(' '); // call a function to display space on LCD
  _delay_ms(1);

  LCD_write(' '); // call a function to display space on LCD
  _delay_ms(1);

  LCD_write(' '); // call a function to display space on LCD
  _delay_ms(1);

  LCD_write(' '); // call a function to display space on LCD
  _delay_ms(1);

  LCD_write(' '); // call a function to display space on LCD
  _delay_ms(1);

  LCD_write('A'); // call a function to display "A" on LCD
  _delay_ms(100);

  LCD_write('V'); // call a function to display "V" on LCD
  _delay_ms(100);

  LCD_write('R'); // call a function to display "R" on LCD
  _delay_ms(100);

  LCD_cmd(0xC0); // move cursor to the start of 2nd line
  _delay_ms(100);

  LCD_cmd(0x0C); // display on, cursor off
  _delay_ms(100);

  LCD_write(' '); // call a function to display space on LCD
  _delay_ms(1);

  LCD_write(' ');
  _delay_ms(1);

  LCD_write(' ');
  _delay_ms(1);

  LCD_write('A'); // call a function to display "A" on LCD
  _delay_ms(100);

  LCD_write('t'); // call a function to display "t" on LCD
  _delay_ms(100);

  LCD_write('m'); // call a function to display "m" on LCD
  _delay_ms(100);

  LCD_write('e'); // call a function to display "e" on LCD
  _delay_ms(100);

  LCD_write('g'); // call a function to display "g" on LCD
  _delay_ms(100);

  LCD_write('a'); // call a function to display "a" on LCD
  _delay_ms(100);

  LCD_write('3'); // call a function to display "3" on LCD
  _delay_ms(100);

  LCD_write('2'); // call a function to display "2" on LCD
  _delay_ms(100);

  LCD_cmd(0x0E); // make display ON, cursor ON
  _delay_ms(1);

  return 0;
}

void init_LCD(void)
{
  LCD_cmd(0x38); // initialization in 8bit mode of 16X2 LCD
  _delay_ms(1);

  LCD_cmd(0x01); // make clear LCD
  _delay_ms(1);

  LCD_cmd(0x02); // return home
  _delay_ms(1);

  LCD_cmd(0x06); // make increment in cursor
  _delay_ms(1);

  LCD_cmd(0x80); // "8" go to first line and "0" is for 0th position
  _delay_ms(1);

  return;
}

//**************sending command on LCD***************//

void LCD_cmd(unsigned char cmd)
{
  LCD_DATA = cmd; // data lines are set to send command
  
  PORTD &= ~(1 << rs); // RS sets 0, for command data
  PORTD &= ~(1 << rw); // RW sets 0, to write data
  PORTD |= (1 << en); // make enable from high to low
  
  _delay_ms(100);
  PORTD &= ~(1 << en); // make enable low

  return;
}

//*****************write data on LCD*****************//

void LCD_write(unsigned char data)
{
  LCD_DATA = data; // data lines are set to send command
  PORTD |= (1 << rs); // RS sets 1, for command data
  PORTD &= ~(1 << rw); // RW sets 0, to write data
  PORTD |= (1 << en); // make enable from high to low

  _delay_ms(100);
  PORTD &= ~(1 << en); // make enable low

  return;
}

Code Explanation

In this section, we will discuss the workings of this code.

#ifndef F_CPU
# define F_CPU 16000000 UL // clock speed is 16 MHz
#endif

#include <avr/io.h> // AVR header
#include <util/delay.h> // delay header

Firstly, we define the clock of the ATmega32 microcontroller at 16 MHz. Next, we define the header tags <avr/io> and <util/delay>. The first tag helps us with the input and output of AVR microcontrollers. Whereas the seconds tag helps us to add delay without making a custom function in the program.

Declaring LCD ports, pins and functions

//******************LCD PROGRAM STARTS*********************//

#define LCD_DATA PORTB // port B is selected as LCD data port
#define ctrl PORTD // port D is selected as LCD command port

#define en PD7 // enable signal is connected to port D pin 7
#define rw PD6 // read/write signal is connected to port D pin 6
#define rs PD5 // register select signal is connected to port D pin 5

void LCD_cmd(unsigned char cmd);
void init_LCD(void);
void LCD_write(unsigned char data);

Now, we declare port B as a data port and port D as a command port. Next, we define three higher pins of port D for the en, rw, and rs pins of the LCD Display. Lastly, we declare the LCD command, LCD initialize, and LCD write functions.

Main function

int main(void)
{
  DDRB = 0xFF; // set LCD data port as output
  DDRD = 0xE0; // set LCD signals (RS, RW, E) as out put

  init_LCD(); // initialize LCD
  _delay_ms(100); // delay of 100 Milli seconds

  LCD_cmd(0x0C); // display on, cursor off
  _delay_ms(100);

  LCD_write(' '); // call a function to display space on LCD
  _delay_ms(1);

  LCD_write(' '); // call a function to display space on LCD
  _delay_ms(1);

  LCD_write(' '); // call a function to display space on LCD
  _delay_ms(1);

  LCD_write(' '); // call a function to display space on LCD
  _delay_ms(1);

  LCD_write(' '); // call a function to display space on LCD
  _delay_ms(1);

  LCD_write('A'); // call a function to display "A" on LCD
  _delay_ms(100);

  LCD_write('V'); // call a function to display "V" on LCD
  _delay_ms(100);

  LCD_write('R'); // call a function to display "R" on LCD
  _delay_ms(100);

  LCD_cmd(0xC0); // move cursor to the start of 2nd line
  _delay_ms(100);

  LCD_cmd(0x0C); // display on, cursor off
  _delay_ms(100);

  LCD_write(' '); // call a function to display space on LCD
  _delay_ms(1);

  LCD_write(' ');
  _delay_ms(1);

  LCD_write(' ');
  _delay_ms(1);

  LCD_write('A'); // call a function to display "A" on LCD
  _delay_ms(100);

  LCD_write('t'); // call a function to display "t" on LCD
  _delay_ms(100);

  LCD_write('m'); // call a function to display "m" on LCD
  _delay_ms(100);

  LCD_write('e'); // call a function to display "e" on LCD
  _delay_ms(100);

  LCD_write('g'); // call a function to display "g" on LCD
  _delay_ms(100);

  LCD_write('a'); // call a function to display "a" on LCD
  _delay_ms(100);

  LCD_write('3'); // call a function to display "3" on LCD
  _delay_ms(100);

  LCD_write('2'); // call a function to display "2" on LCD
  _delay_ms(100);

  LCD_cmd(0x0E); // make display ON, cursor ON
  _delay_ms(1);

  return 0;
}

In the main function, first we set the data and command ports as output. Then we call the init_LCD() and LCD_cmd() functions with a delay of 100 ms. This command function turns the cursor off. After this, we print “AVR” in the middle of the first line, and by using LCD_cmd, we move to the second row. After moving to the second row, we print “Atmega32” in the middle of this row. At last, by using LCD_cmd (0x0E), we turn on the display and the cursor.

LCD Initializing Function

void init_LCD(void)
{
  LCD_cmd(0x38); // initialization in 8bit mode of 16X2 LCD
  _delay_ms(1);

  LCD_cmd(0x01); // make clear LCD
  _delay_ms(1);

  LCD_cmd(0x02); // return home
  _delay_ms(1);

  LCD_cmd(0x06); // make increment in cursor
  _delay_ms(1);

  LCD_cmd(0x80); // go to first line and "0" is for 0th position
  _delay_ms(1);

  return;
}

The init_LCD function initializes the LCD display. Firstly, we set the 8-bit mode for data transfer. Then we return the displays cursor to the home or starting position. The LCD_cmd(0x06) command sets the increment mode, which means the Display will increment to the next position after printing a character. Lastly, we move the cursor to the first position of the display and return to the function.

LCD command function

//**************sending command on LCD***************//

void LCD_cmd(unsigned char cmd)
{
  LCD_DATA = cmd; // data lines are set to send command
  
  PORTD &= ~(1 << rs); // RS sets 0, for command data
  PORTD &= ~(1 << rw); // RW sets 0, write data
  PORTD |= (1 << en); // make enable high, triggering pulse from high to low
  
  _delay_ms(100);
  PORTD &= ~(1 << en); // make enable low

  return;
}

In the LCD_cmd function body, first we set data lines to send commands. Next, we set the rs and rw pins to low and the en pin to high. After about 100 ms, we turn the en pin to low and return from the function.

LCD character function

//*****************write data on LCD*****************//

void LCD_write(unsigned char data)
{
  LCD_DATA = data; // data lines are set to send command
  PORTD |= (1 << rs); // RS sets 1, for character data
  PORTD &= ~(1 << rw); // RW sets 0, write data
  PORTD |= (1 << en); // make enable high triggering pulse from high to low

  _delay_ms(100);
  PORTD &= ~(1 << en); // make enable low

  return;
}

Now, in the function body, we first set the data lines to command. Then we set the RS to high and turn the RW to low. Next, we set the en pin high, and with a delay of 100 ms, we turn this pin low. Lastly, we return from this function.

Simulation on Proteus

Compile the above code and dump the HEX file into the AVR microcontroller as described in the previous tutorials. Make the necessary settings and check the display on the LCD.

LCD interfacing with ATmega32

Basic Commands used in LCD Display

Conclusion

In this tutorial, we have covered the following topics:

• What is LCD.
• Pin description and programming of the LCD.
• Schematic diagram.
• Code with an explanation.
• Proteus simulation

Related Articles

You may also like to read:

• I2C LCD interfacing with ESP32 and ESP8266 in Arduino IDE
• I2C LCD with STM32 Blue Pill using STM32CubeIDE
• ESP32 with MPU6050 Accelerometer, Gyroscope, and Temperature Sensor ( Arduino IDE)
• DC motor interfacing with atmega32 and L293
• Displaying Images in ESP32 and ESP8266 Web Server
• STM32 Blue Pill with 4-Digit 7 Segment Display using STM32CubeIDE

This is all for this article. Thanks for visiting our website. Keep sharing and keep learning 🙂