Boundary-Scan Chain - Corelis Inc. (original) (raw)

Skip to content

• Educational: JTAG Interface & Boundary-Scan Educational Resources
• JTAG Tutorials
• Design for Testability Tips and Guidelines
  • Boundary-Scan Chain
  • Board Level Design
  • Design Engineers Role in Boundary-Scan Test
  • Improving Test Coverage
  • Improve Flash Programming Speed with Firecron JTS15S
• JTAG Boundary-Scan & JET Technology Benefits FAQ
• JTAG Boundary-Scan Glossary
• JTAG Method Literature

Boundary-Scan Chain Design for Testability

Successful testing and ISP of your design depends on a fully functional boundary-scan chain. Maximum test coverage is achieved by testing all JTAG devices simultaneously.

• Scan-Chain
• Scan Chain Debug Access & Test Points
• Check devices for full JTAG compliance
• JTAG Interface Connector (TAP)

Scan-Chain

Place all JTAG devices into a single scan-chain and add test points for debug access—all JTAG devices are tested simultaneously in the serial chain.

Multiple scan-chains are acceptable but should be merged externally; in some cases this is the preferred method:

• Use a multi-TAP JTAG controller to externally combine multiple JTAG scan-chains into a single chain. Each JTAG TAP is actively buffered and can interface to different voltage levels.
• Alternatively combine multiple chains with a fixture or cable. Lower reliability and susceptible to noise.

Scan Chain Debug Access & Test Points

Resistors can be designed into the scan chain as a way to selectively bypass devices in the scan chain for debugging.

Check devices for full JTAG compliance

Not all devices fully comply to the IEEE-1149.1 standard. When analyzing or troubleshooting devices, consider the following cases and guidelines.

• Alternatively combine multiple chains with a fixture or cable. Lower reliability and susceptible to noise.
• Place devices that do not include a boundary-scan register or do not support the EXTEST instruction in BYPASS.
• Group components with similar voltage levels and utilize a multi-JTAG TAP controller for programmable voltage interfacing or add level shifting components to the design.
• Treat TCK as a critical high speed clock signal during layout.
• Always consider signal loading on the common signals TCK and TMS and proper routing for good signal quality. When driving a large number of JTAG devices (more than 5), add TCK and TMS buffering.
• Dedicate a schematic page for a block diagram of the JTAG scan-chain.

JTAG Interface Connector (TAP)

Corelis recommends the Corelis JTAG TAP pin-out for robust one-to-one connection between the JTAG controller and the target.

Additional guidelines include:

• A solid ground is very important; every other pin on Corelis TAPs is ground on cable providing noise immunity.
• Follow the IC vendor’s JTAG signal termination guidelines first, then Corelis’ guidelines.
• When using Multiple JTAG TAP connectors:
• Group components by IC vendor.
• Group components by voltage.
• Group components by maximum device speed.
• Group by devices that require the TRST_N signal.
• Use jumpers or additional logic to isolate devices for debugging.

Jumper example to isolate a single device

Logic example to isolate a single device

The IEEE-1149.1 standard does not define type of connector used for JTAG, so there is a wide variety of options when selecting a connection method.

• Although the pinouts may be different, most vendors use standard 0.1″ x 0.1″ pitch headers.
• Shrouded header recommended to prevent incorrect insertion.
• Additional connector types include:
• 0.050″ x 0.050″ pin spacing.
• Test points for fixture probe access to JTAG signals.
• Keep JTAG TAP cables as short as possible. Cables should ideally be under 12″ in length, but shorter is better!
• When using custom cable adapters, ensure adequate grounding is provided between the JTAG controller and the target.
• Third party JTAG tools may require a separate JTAG TAP connection for an individual component.

“What’s New” @Corelis

ABOUT US

Corelis is the leader in providing embedded hardware test solutions, called ScanExpress, the industry’s broadest line of JTAG Boundary-Scan software and hardware products that combine exceptional ease of use with advanced technical innovation and unmatched engineering support.

DESIGN FOR TEST

Embedded Hardware Designers! Have you created a solid test plan that will insure early fault or failure detection? Download this 58-page guide. Our engineers are also here for you at each step of the design, planning, and test phases.

CERTIFICATION

CONNECT & EXPLORE

CONTACT

13100 Alondra Blvd., Suite 102
Cerritos, CA 90703

Page load link

Go to Top