GILDO S DA SILVA JUNIOR | UNIPLI (original) (raw)
Uploads
Papers by GILDO S DA SILVA JUNIOR
Journal of Applied Oral Science, 2005
The aim of this study was to determine the effect of a softstart polymerization method from Quart... more The aim of this study was to determine the effect of a softstart polymerization method from Quartz-Tungsten-Halogen (QTH) and Plasma Arc (PAC) curing units on microleakage of Class V composite resin restorations with dentin cavosurface margins. Seventy-five bovine incisors received standardized class V cavities in all dentin margins. Teeth were divided into 5 equal groups according to the curing cycle. The cavities were incrementally restored with a composite resin (Single Bond/Z-100, 3M). Light curing was applied as follows: Group I: PAC light continuous-cycle curing at 1600 mW/cm2 for 3s; Group II: PAC light step-cycle curing (2s at 800 mW/cm2 then 4s at 1600 mW/cm2); Group III: QTH light continuous-cycle curing at 400 mW/cm2 for 40s; Group IV: QTH light ramp-cycle curing (from 100 to 600 mW/cm2 in 15s followed by 25s at 600 mW/cm2); Group V: QTH light pulse-delay curing (200 mW/cm2 for 3s followed by 3 min delay then 600 mW/cm2 for 30s). Teeth were stored in distilled water at 37ºC for 30 days and then subjected to thermocycling for 500 cycles at 5 and 55ºC. Root apices were sealed and teeth coated with nail varnish before they were immersed in 0.5% fuchsine red dye solution. Teeth were then sectioned and slices were scanned with a computer scanner to determine the area of dye leakage using a computer program (Image Tools). Images of tooth slices were also visually examined under magnification and dye penetration along the tooth/restoration interface was scored. Significant differences in the degree of dye penetration and leakage were detected between groups (p<.05). Groups I and II had significantly higher values of dye penetration and leakage than groups III, IV and V. In conclusion, the use of PAC light curing in a continuous or step cycle modes resulted in increased microleakage of Class V resin composite restorations compared with medium intensity QTH light curing. Pulse, ramp and continuous-cycle curing modes with QTH light resulted in similar degrees of microleakage.
... Priscila Randazzo-Moura1, Gildo Bernardo Leite1, Gustavo Henrique Silva2, Valdemar Antonio Pa... more ... Priscila Randazzo-Moura1, Gildo Bernardo Leite1, Gustavo Henrique Silva2, Valdemar Antonio Paffaro J??nior2, Ad??lia Cristina Oliveira Cintra3 ... 27. Rasgado-Flores H, Sanchez-Armass S, Blaustein MP, Nachshen DA (1987) Strontium, barium, and manganese metabolism in ...
Journal of Applied Oral Science, 2005
The aim of this study was to determine the effect of a softstart polymerization method from Quart... more The aim of this study was to determine the effect of a softstart polymerization method from Quartz-Tungsten-Halogen (QTH) and Plasma Arc (PAC) curing units on microleakage of Class V composite resin restorations with dentin cavosurface margins. Seventy-five bovine incisors received standardized class V cavities in all dentin margins. Teeth were divided into 5 equal groups according to the curing cycle. The cavities were incrementally restored with a composite resin (Single Bond/Z-100, 3M). Light curing was applied as follows: Group I: PAC light continuous-cycle curing at 1600 mW/cm2 for 3s; Group II: PAC light step-cycle curing (2s at 800 mW/cm2 then 4s at 1600 mW/cm2); Group III: QTH light continuous-cycle curing at 400 mW/cm2 for 40s; Group IV: QTH light ramp-cycle curing (from 100 to 600 mW/cm2 in 15s followed by 25s at 600 mW/cm2); Group V: QTH light pulse-delay curing (200 mW/cm2 for 3s followed by 3 min delay then 600 mW/cm2 for 30s). Teeth were stored in distilled water at 37ºC for 30 days and then subjected to thermocycling for 500 cycles at 5 and 55ºC. Root apices were sealed and teeth coated with nail varnish before they were immersed in 0.5% fuchsine red dye solution. Teeth were then sectioned and slices were scanned with a computer scanner to determine the area of dye leakage using a computer program (Image Tools). Images of tooth slices were also visually examined under magnification and dye penetration along the tooth/restoration interface was scored. Significant differences in the degree of dye penetration and leakage were detected between groups (p<.05). Groups I and II had significantly higher values of dye penetration and leakage than groups III, IV and V. In conclusion, the use of PAC light curing in a continuous or step cycle modes resulted in increased microleakage of Class V resin composite restorations compared with medium intensity QTH light curing. Pulse, ramp and continuous-cycle curing modes with QTH light resulted in similar degrees of microleakage.
... Priscila Randazzo-Moura1, Gildo Bernardo Leite1, Gustavo Henrique Silva2, Valdemar Antonio Pa... more ... Priscila Randazzo-Moura1, Gildo Bernardo Leite1, Gustavo Henrique Silva2, Valdemar Antonio Paffaro J??nior2, Ad??lia Cristina Oliveira Cintra3 ... 27. Rasgado-Flores H, Sanchez-Armass S, Blaustein MP, Nachshen DA (1987) Strontium, barium, and manganese metabolism in ...