AWS::MediaConnect::FlowOutput - AWS CloudFormation (original) (raw)

The AWS::MediaConnect::FlowOutput resource defines the destination address, protocol, and port that AWS Elemental MediaConnect sends the ingested video to. Each flow can have up to 50 outputs. An output can have the same protocol or a different protocol from the source. The following protocols are supported: RIST, RTP, RTP-FEC, SRT-listener, SRT-caller, Zixi pull, and Zixi push. CDI and ST 2110 JPEG XS protocols are not currently supported by AWS CloudFormation.

To declare this entity in your AWS CloudFormation template, use the following syntax:

JSON

{
  "Type" : "AWS::MediaConnect::FlowOutput",
  "Properties" : {
      "CidrAllowList" : [ String, ... ],
      "Description" : String,
      "Destination" : String,
      "Encryption" : Encryption,
      "FlowArn" : String,
      "MaxLatency" : Integer,
      "MediaStreamOutputConfigurations" : [ MediaStreamOutputConfiguration, ... ],
      "MinLatency" : Integer,
      "Name" : String,
      "NdiProgramName" : String,
      "NdiSpeedHqQuality" : Integer,
      "OutputStatus" : String,
      "Port" : Integer,
      "Protocol" : String,
      "RemoteId" : String,
      "SmoothingLatency" : Integer,
      "StreamId" : String,
      "VpcInterfaceAttachment" : VpcInterfaceAttachment
    }
}

CidrAllowList

The range of IP addresses that should be allowed to initiate output requests to this flow. These IP addresses should be in the form of a Classless Inter-Domain Routing (CIDR) block; for example, 10.0.0.0/16.

Required: No

Type: Array of String

Update requires: No interruption

Description

A description of the output. This description appears only on the MediaConnect console and will not be seen by the end user.

Required: No

Type: String

Update requires: No interruption

Destination

The IP address where you want to send the output.

Required: No

Type: String

Update requires: No interruption

Encryption

The type of key used for the encryption. If no keyType is provided, the service will use the default setting (static-key). Allowable encryption types: static-key.

Required: No

Type: Encryption

Update requires: No interruption

FlowArn

The Amazon Resource Name (ARN) of the flow this output is attached to.

Required: Yes

Type: String

Update requires: No interruption

MaxLatency

The maximum latency in milliseconds. This parameter applies only to RIST-based and Zixi-based streams.

Required: No

Type: Integer

Update requires: No interruption

MediaStreamOutputConfigurations

The media streams that are associated with the output, and the parameters for those associations.

Required: No

Type: Array of MediaStreamOutputConfiguration

Update requires: No interruption

MinLatency

The minimum latency in milliseconds for SRT-based streams. In streams that use the SRT protocol, this value that you set on your MediaConnect source or output represents the minimal potential latency of that connection. The latency of the stream is set to the highest number between the sender’s minimum latency and the receiver’s minimum latency.

Required: No

Type: Integer

Update requires: No interruption

Name

The name of the bridge's output.

Required: No

Type: String

Update requires: Replacement

NdiProgramName

A suffix for the names of the NDI sources that the flow creates. If a custom name isn't specified, MediaConnect uses the output name.

Required: No

Type: String

Update requires: No interruption

NdiSpeedHqQuality

A quality setting for the NDI Speed HQ encoder.

Required: No

Type: Integer

Update requires: No interruption

OutputStatus

Property description not available.

Required: No

Type: String

Allowed values: ENABLED | DISABLED

Update requires: No interruption

Port

The port to use when content is distributed to this output.

Required: No

Type: Integer

Update requires: No interruption

Protocol

The protocol to use for the output.

Note

AWS Elemental MediaConnect no longer supports the Fujitsu QoS protocol. This reference is maintained for legacy purposes only.

Required: Yes

Type: String

Update requires: No interruption

RemoteId

The remote ID for the Zixi-pull stream.

Required: No

Type: String

Update requires: No interruption

SmoothingLatency

The smoothing latency in milliseconds for RIST, RTP, and RTP-FEC streams.

Required: No

Type: Integer

Update requires: No interruption

StreamId

The stream ID that you want to use for this transport. This parameter applies only to Zixi and SRT caller-based streams.

Required: No

Type: String

Update requires: No interruption

VpcInterfaceAttachment

The name of the VPC interface attachment to use for this output.

Required: No

Type: VpcInterfaceAttachment

Update requires: No interruption

Ref

When you pass the logical ID of this resource to the intrinsic Ref function, Ref returns the output ARN. For example:

{ "Ref": "arn:aws:mediaconnect:us-east-1:111122223333:output:2-3aBC45dEF67hiJ89-c34de5fG678h:NYCOutput" }

For more information about using the Ref function, see Ref.

Fn::GetAtt

The Fn::GetAtt intrinsic function returns a value for a specified attribute of this type. The following are the available attributes and sample return values.

For more information about using the Fn::GetAtt intrinsic function, see Fn::GetAtt.

OutputArn

The ARN of the output.