Futoshi Komine - Academia.edu (original) (raw)

Papers by Futoshi Komine

Nihon Hotetsu Shika Gakkai Zasshi, 1994

Nihon Hotetsu Shika Gakkai Zasshi, 1996

Annals of Japan Prosthodontic Society, 2012

Quintessence international (Berlin, Germany : 1985)

To evaluate the influence of firing procedures on the marginal distortion of electroformed metal-... more To evaluate the influence of firing procedures on the marginal distortion of electroformed metal-ceramic crown restorations. Twenty-four standardized specimens were fabricated using a gold-electroforming system and were characterized by 3 finish line forms: shoulder (S-type), rounded shoulder (RS-type), and deep chamfer (DC-type) preparations. Marginal discrepancies were measured at 6 stages: before the firing procedures, after the gold-bonder application, after the opaque porcelain firing, after the dentin porcelain firing, after the enamel porcelain firing, and after the glazing firing. Marginal discrepancy values were recorded at 60 randomly chosen points along the circumferential margin using a laser microscope. Marginal distortion values were defined as the differences in the marginal discrepancies between the baseline (prefiring) levels and those after each firing procedure. All statistical analyses were performed using the Friedman and Kruskal-Wallis tests (alpha = .05). For ...

Dental materials journal, 2015

To evaluate the effects of various surface preparations on shear bond strength of a gingiva-color... more To evaluate the effects of various surface preparations on shear bond strength of a gingiva-colored indirect composite material and zirconia framework. Zirconia disks were prepared with one of nine surface treatments: hydrofluoric acid etching (HF), heating at 1,000°C for 10 min (HT), wet-grinding with 600- and 1500-grit SiC paper (SiC 600 and 1500), alumina-blasting at 0.1, 0.2, 0.4 and 0.6 MPa (AB 0.1, 0.2, 0.4, and 0.6), and no treatment (NT). An indirect composite material was bonded to zirconia. Shear bond strengths were measured. Bond strength was significantly higher in AB 0.2, 0.4, and 0.6 groups than in other groups at 0 and 20,000 thermocycles. Post-thermocycling bond strength was lower in NT, HF, and HT groups than in other groups. Alumina-blasting with 0.2 MPa or higher yielded sufficient durable bond strength between gingiva-colored indirect composite and zirconia frameworks. Hydrofluoric acid etching and heat treatment did not achieve durable bond strengths.

The journal of adhesive dentistry, 2015

This study evaluated the long-term shear bond strength between an indirect composite material and... more This study evaluated the long-term shear bond strength between an indirect composite material and a zirconia framework coated with silica-based ceramics, taking the effect of different primers into account. A total of 165 airborne-particle abraded zirconia disks were subjected to one of three pretreatments: no pretreatment (ZR-AB), airborne-particle abrasion of zirconia coated with feldspathic porcelain (ZR-PO-AB), and 9.5% hydrofluoric acid etching of zirconia coated with feldspathic porcelain (ZR-PO-HF). An indirect composite material (Estenia C&B) was then bonded to the zirconia disks after they were treated with one of the following primers: Clearfil Photo Bond (CPB), Clearfil Photo Bond with Clearfil Porcelain Bond Activator (CPB + Activator), Estenia Opaque Primer (EOP), Porcelain Liner M Liquid B (PLB), or no priming (CON, control group). Shear bond strength was tested after 100,000 thermocycles, and the data were analyzed using the Steel-Dwass U-test (α = 0.05). For ZR-PO-AB...

Nihon Hotetsu Shika Gakkai Zasshi, 1994

Nihon Hotetsu Shika Gakkai Zasshi

Nihon Hotetsu Shika Gakkai Zasshi, 2003

Nihon Hotetsu Shika Gakkai Zasshi, 2004

Nihon Hotetsu Shika Gakkai Zasshi, 2000

Nihon Hotetsu Shika Gakkai Zasshi, 2001

Quintessence international (Berlin, Germany : 1985)

Indirect composites are promising alternatives as veneering materials for zirconium dioxide (zirc... more Indirect composites are promising alternatives as veneering materials for zirconium dioxide (zirconia) ceramic frameworks. This study evaluated the effects of priming agents and a high-flow bonding agent on the short-term bond of an indirect composite material to a zirconia framework material. Indirect composite (Estenia C and B) was bonded to particle-abraded zirconia samples (Katana, n = 144) using no (control) or 1 of 8 priming agents: All Bond 2 Primer B (ABB), Alloy Primer (ALP), Clearfil Ceramic Primer (CCP), Clearfil Photo Bond (CPB), Clearfil Photo Bond with Clearfil Porcelain Bond Activator (CPB+Activator), Estenia Opaque Primer (EOP), Porcelain Liner M Liquid A (PLA), and V-Primer (VPR) with or without a high-flow bonding agent (Estenia C and B Opaque). Shear bond strength was tested after 24-hour wet storage. Data were analyzed with Levene test for equality of variance, Dunnett T3 multiple comparison, and Mann-Whitney U test (P = .05). Mean bond strengths without the high...

Dental materials journal, 2014

This study evaluated fracture load of single-tooth, implant-supported, zirconia-based, porcelain-... more This study evaluated fracture load of single-tooth, implant-supported, zirconia-based, porcelain- and indirect composite-layered restorations after artificial aging. Forty-four zirconia-based molar restorations were fabricated on implant abutments and divided into four groups, namely, zirconia-based all-ceramic restorations (ZAC group) and three types of zirconia-based composite-layered restorations (ZIC-P, ZIC-E, and ZIC groups). Before layering an indirect composite material, the zirconia copings in the ZIC-P and ZIC-E groups were primed with Clearfil Photo Bond and Estenia Opaque Primer, respectively. All restorations were cemented on the abutments with glass-ionomer cement and then subjected to thermal cycling and cyclic loading. All specimens survived thermal cycling and cyclic loading. The fracture load of the ZIC-P group (2.72 kN) was not significantly different from that of the ZAC group (3.05 kN). The fracture load of the zirconia-based composite-layered restoration primed ...

The journal of adhesive dentistry, 2012

This study evaluated and compared bonding characteristics of resin-based luting agents and specia... more This study evaluated and compared bonding characteristics of resin-based luting agents and special ceramic primers to zirconia. Disk specimens (n = 242) were fabricated from zirconium dioxide ceramics (Katana) and bonded with four resin-based luting agents without priming. In addition, zirconia was bonded with 7 bondingsystem combinations of three priming agents and three resin-based luting agents. Two of the resin-based luting agents and two ceramic priming agents contain an identical adhesive monomer, 10-methacryloyloxydecyl dihydrogen phosphate (MDP), either in the material itself or in the priming agent. Shear bond strength was determined after 20,000 cycles of thermocycling. The Kruskal-Wallis test was performed for both pre- and post-thermocycling groups to evaluate the difference among primer and luting agent variations. On the basis of the Kruskal-Wallis test, Steel-Dwass multiple comparisons were further performed to compare the difference among four luting agents and seven...

The journal of adhesive dentistry, 2010

The purpose of the current study was to evaluate the effect of acidic primers on the bond strengt... more The purpose of the current study was to evaluate the effect of acidic primers on the bond strength and durability of an acrylic resin luting agent to zirconia. Disk specimens were fabricated from zirconia partially stabilized with yttrium oxide (Katana, Noritake Dental Supply). The disks were treated with one of the following acidic primers: Acryl Bond (Shofu), All Bond II Primer B (Bisco), Alloy Primer (Kuraray), Estenia Opaque Primer (Kuraray), Eye Sight Opaque Primer (Kanebo), M.L. Primer (Shofu), MR. Bond (Tokuyama Dental), or Super-Bond Liquid (Sun Medical). Unprimed specimens served as the control. The disks were bonded with a tri-n-butylborane (TBB)-initiated acrylic resin. Shear bond strengths were determined both before and after 10,000 thermocycles (5°C and 55°C, 1 min dwell time each). The pre-thermocycling bond strength ranged from 0.7 MPa to 30.8 MPa, whereas post-thermocycling bond strength varied from 0.3 MPa to 17.6 MPa. The significantly highest post-thermocycling b...

Quintessence international (Berlin, Germany : 1985), 2008

Fluorescence, opalescence, and translucency are critical for restorative materials to mimic the o... more Fluorescence, opalescence, and translucency are critical for restorative materials to mimic the optical properties and appearance of natural teeth. This case report describes the restoration of multiple anterior teeth with CAD/CAM-fabricated glass-infiltrated aluminum oxide ceramic (In-Ceram Alumina, Vita Zahnfabrik) crowns and illustrates the technical steps to achieve an adequate amount of fluorescence in the ceramic veneering material. CAD/CAM aluminum oxide ceramic copings and frameworks can be predictable and successful when replacing missing tooth structure and imitating optical properties of natural teeth. A modified layering technique enhances fluorescence within the veneering ceramic and provides an esthetic appearance of glass-infiltrated aluminum oxide ceramic restorations.

The Journal of prosthetic dentistry, 2006

Advances in computer-aided design/computer-assisted manufacturing (CAD/CAM) technology purportedl... more Advances in computer-aided design/computer-assisted manufacturing (CAD/CAM) technology purportedly enhance the marginal fit of dental restorations. However, little information is available on the marginal accuracy of restorations manufactured with various CAD/CAM systems. The purpose of this study was to evaluate and compare the marginal accuracy and refinement time of titanium copings fabricated by 3 different CAD/CAM systems relative to standard casting techniques. Sixty-four stone die duplicates of a human maxillary central incisor, prepared for a metal-ceramic crown, with a uniform chamfer design, were divided into 4 groups (n=16). The specimens were restored with titanium copings using CAD/CAM systems Pro 50 (PRO), DCS (DCS), and Everest (EVE). A conventional titanium casting technique, Biotan (BIO), served as a control. Vertical and horizontal discrepancies between restoration margins and the preparations were each measured before and after manual refinement. This refinement w...

Japanese Dental Science Review, 2012

Clinical oral implants research, Jan 12, 2014

To evaluate the effects of framework design and layering material on the fracture strength of imp... more To evaluate the effects of framework design and layering material on the fracture strength of implant-supported zirconia-based molar crowns. Sixty-six titanium abutments (GingiHue Post) were tightened onto dental implants (Implant Lab Analog). These abutment-implant complexes were randomly divided into three groups (n = 22) according to the design of the zirconia framework (Katana), namely, uniform-thickness (UNI), anatomic (ANA), and supported anatomic (SUP) designs. The specimens in each design group were further divided into two subgroups (n = 11): zirconia-based all-ceramic restorations (ZAC group) and zirconia-based restorations with an indirect composite material (Estenia C&B) layered onto the zirconia framework (ZIC group). All crowns were cemented on implant abutments, after which the specimens were tested for fracture resistance. The data were analyzed with the Kruskal-Wallis test and the Mann-Whitney U-test with the Bonferroni correction (α = 0.05). The following mean frac...

Nihon Hotetsu Shika Gakkai Zasshi, 1994

Nihon Hotetsu Shika Gakkai Zasshi, 1996

Annals of Japan Prosthodontic Society, 2012

Quintessence international (Berlin, Germany : 1985)

To evaluate the influence of firing procedures on the marginal distortion of electroformed metal-... more To evaluate the influence of firing procedures on the marginal distortion of electroformed metal-ceramic crown restorations. Twenty-four standardized specimens were fabricated using a gold-electroforming system and were characterized by 3 finish line forms: shoulder (S-type), rounded shoulder (RS-type), and deep chamfer (DC-type) preparations. Marginal discrepancies were measured at 6 stages: before the firing procedures, after the gold-bonder application, after the opaque porcelain firing, after the dentin porcelain firing, after the enamel porcelain firing, and after the glazing firing. Marginal discrepancy values were recorded at 60 randomly chosen points along the circumferential margin using a laser microscope. Marginal distortion values were defined as the differences in the marginal discrepancies between the baseline (prefiring) levels and those after each firing procedure. All statistical analyses were performed using the Friedman and Kruskal-Wallis tests (alpha = .05). For ...

Dental materials journal, 2015

To evaluate the effects of various surface preparations on shear bond strength of a gingiva-color... more To evaluate the effects of various surface preparations on shear bond strength of a gingiva-colored indirect composite material and zirconia framework. Zirconia disks were prepared with one of nine surface treatments: hydrofluoric acid etching (HF), heating at 1,000°C for 10 min (HT), wet-grinding with 600- and 1500-grit SiC paper (SiC 600 and 1500), alumina-blasting at 0.1, 0.2, 0.4 and 0.6 MPa (AB 0.1, 0.2, 0.4, and 0.6), and no treatment (NT). An indirect composite material was bonded to zirconia. Shear bond strengths were measured. Bond strength was significantly higher in AB 0.2, 0.4, and 0.6 groups than in other groups at 0 and 20,000 thermocycles. Post-thermocycling bond strength was lower in NT, HF, and HT groups than in other groups. Alumina-blasting with 0.2 MPa or higher yielded sufficient durable bond strength between gingiva-colored indirect composite and zirconia frameworks. Hydrofluoric acid etching and heat treatment did not achieve durable bond strengths.

The journal of adhesive dentistry, 2015

This study evaluated the long-term shear bond strength between an indirect composite material and... more This study evaluated the long-term shear bond strength between an indirect composite material and a zirconia framework coated with silica-based ceramics, taking the effect of different primers into account. A total of 165 airborne-particle abraded zirconia disks were subjected to one of three pretreatments: no pretreatment (ZR-AB), airborne-particle abrasion of zirconia coated with feldspathic porcelain (ZR-PO-AB), and 9.5% hydrofluoric acid etching of zirconia coated with feldspathic porcelain (ZR-PO-HF). An indirect composite material (Estenia C&B) was then bonded to the zirconia disks after they were treated with one of the following primers: Clearfil Photo Bond (CPB), Clearfil Photo Bond with Clearfil Porcelain Bond Activator (CPB + Activator), Estenia Opaque Primer (EOP), Porcelain Liner M Liquid B (PLB), or no priming (CON, control group). Shear bond strength was tested after 100,000 thermocycles, and the data were analyzed using the Steel-Dwass U-test (α = 0.05). For ZR-PO-AB...

Nihon Hotetsu Shika Gakkai Zasshi, 1994

Nihon Hotetsu Shika Gakkai Zasshi

Nihon Hotetsu Shika Gakkai Zasshi, 2003

Nihon Hotetsu Shika Gakkai Zasshi, 2004

Nihon Hotetsu Shika Gakkai Zasshi, 2000

Nihon Hotetsu Shika Gakkai Zasshi, 2001

Quintessence international (Berlin, Germany : 1985)

Indirect composites are promising alternatives as veneering materials for zirconium dioxide (zirc... more Indirect composites are promising alternatives as veneering materials for zirconium dioxide (zirconia) ceramic frameworks. This study evaluated the effects of priming agents and a high-flow bonding agent on the short-term bond of an indirect composite material to a zirconia framework material. Indirect composite (Estenia C and B) was bonded to particle-abraded zirconia samples (Katana, n = 144) using no (control) or 1 of 8 priming agents: All Bond 2 Primer B (ABB), Alloy Primer (ALP), Clearfil Ceramic Primer (CCP), Clearfil Photo Bond (CPB), Clearfil Photo Bond with Clearfil Porcelain Bond Activator (CPB+Activator), Estenia Opaque Primer (EOP), Porcelain Liner M Liquid A (PLA), and V-Primer (VPR) with or without a high-flow bonding agent (Estenia C and B Opaque). Shear bond strength was tested after 24-hour wet storage. Data were analyzed with Levene test for equality of variance, Dunnett T3 multiple comparison, and Mann-Whitney U test (P = .05). Mean bond strengths without the high...

Dental materials journal, 2014

This study evaluated fracture load of single-tooth, implant-supported, zirconia-based, porcelain-... more This study evaluated fracture load of single-tooth, implant-supported, zirconia-based, porcelain- and indirect composite-layered restorations after artificial aging. Forty-four zirconia-based molar restorations were fabricated on implant abutments and divided into four groups, namely, zirconia-based all-ceramic restorations (ZAC group) and three types of zirconia-based composite-layered restorations (ZIC-P, ZIC-E, and ZIC groups). Before layering an indirect composite material, the zirconia copings in the ZIC-P and ZIC-E groups were primed with Clearfil Photo Bond and Estenia Opaque Primer, respectively. All restorations were cemented on the abutments with glass-ionomer cement and then subjected to thermal cycling and cyclic loading. All specimens survived thermal cycling and cyclic loading. The fracture load of the ZIC-P group (2.72 kN) was not significantly different from that of the ZAC group (3.05 kN). The fracture load of the zirconia-based composite-layered restoration primed ...

The journal of adhesive dentistry, 2012

This study evaluated and compared bonding characteristics of resin-based luting agents and specia... more This study evaluated and compared bonding characteristics of resin-based luting agents and special ceramic primers to zirconia. Disk specimens (n = 242) were fabricated from zirconium dioxide ceramics (Katana) and bonded with four resin-based luting agents without priming. In addition, zirconia was bonded with 7 bondingsystem combinations of three priming agents and three resin-based luting agents. Two of the resin-based luting agents and two ceramic priming agents contain an identical adhesive monomer, 10-methacryloyloxydecyl dihydrogen phosphate (MDP), either in the material itself or in the priming agent. Shear bond strength was determined after 20,000 cycles of thermocycling. The Kruskal-Wallis test was performed for both pre- and post-thermocycling groups to evaluate the difference among primer and luting agent variations. On the basis of the Kruskal-Wallis test, Steel-Dwass multiple comparisons were further performed to compare the difference among four luting agents and seven...

The journal of adhesive dentistry, 2010

The purpose of the current study was to evaluate the effect of acidic primers on the bond strengt... more The purpose of the current study was to evaluate the effect of acidic primers on the bond strength and durability of an acrylic resin luting agent to zirconia. Disk specimens were fabricated from zirconia partially stabilized with yttrium oxide (Katana, Noritake Dental Supply). The disks were treated with one of the following acidic primers: Acryl Bond (Shofu), All Bond II Primer B (Bisco), Alloy Primer (Kuraray), Estenia Opaque Primer (Kuraray), Eye Sight Opaque Primer (Kanebo), M.L. Primer (Shofu), MR. Bond (Tokuyama Dental), or Super-Bond Liquid (Sun Medical). Unprimed specimens served as the control. The disks were bonded with a tri-n-butylborane (TBB)-initiated acrylic resin. Shear bond strengths were determined both before and after 10,000 thermocycles (5°C and 55°C, 1 min dwell time each). The pre-thermocycling bond strength ranged from 0.7 MPa to 30.8 MPa, whereas post-thermocycling bond strength varied from 0.3 MPa to 17.6 MPa. The significantly highest post-thermocycling b...

Quintessence international (Berlin, Germany : 1985), 2008

Fluorescence, opalescence, and translucency are critical for restorative materials to mimic the o... more Fluorescence, opalescence, and translucency are critical for restorative materials to mimic the optical properties and appearance of natural teeth. This case report describes the restoration of multiple anterior teeth with CAD/CAM-fabricated glass-infiltrated aluminum oxide ceramic (In-Ceram Alumina, Vita Zahnfabrik) crowns and illustrates the technical steps to achieve an adequate amount of fluorescence in the ceramic veneering material. CAD/CAM aluminum oxide ceramic copings and frameworks can be predictable and successful when replacing missing tooth structure and imitating optical properties of natural teeth. A modified layering technique enhances fluorescence within the veneering ceramic and provides an esthetic appearance of glass-infiltrated aluminum oxide ceramic restorations.

The Journal of prosthetic dentistry, 2006

Advances in computer-aided design/computer-assisted manufacturing (CAD/CAM) technology purportedl... more Advances in computer-aided design/computer-assisted manufacturing (CAD/CAM) technology purportedly enhance the marginal fit of dental restorations. However, little information is available on the marginal accuracy of restorations manufactured with various CAD/CAM systems. The purpose of this study was to evaluate and compare the marginal accuracy and refinement time of titanium copings fabricated by 3 different CAD/CAM systems relative to standard casting techniques. Sixty-four stone die duplicates of a human maxillary central incisor, prepared for a metal-ceramic crown, with a uniform chamfer design, were divided into 4 groups (n=16). The specimens were restored with titanium copings using CAD/CAM systems Pro 50 (PRO), DCS (DCS), and Everest (EVE). A conventional titanium casting technique, Biotan (BIO), served as a control. Vertical and horizontal discrepancies between restoration margins and the preparations were each measured before and after manual refinement. This refinement w...

Japanese Dental Science Review, 2012

Clinical oral implants research, Jan 12, 2014

To evaluate the effects of framework design and layering material on the fracture strength of imp... more To evaluate the effects of framework design and layering material on the fracture strength of implant-supported zirconia-based molar crowns. Sixty-six titanium abutments (GingiHue Post) were tightened onto dental implants (Implant Lab Analog). These abutment-implant complexes were randomly divided into three groups (n = 22) according to the design of the zirconia framework (Katana), namely, uniform-thickness (UNI), anatomic (ANA), and supported anatomic (SUP) designs. The specimens in each design group were further divided into two subgroups (n = 11): zirconia-based all-ceramic restorations (ZAC group) and zirconia-based restorations with an indirect composite material (Estenia C&B) layered onto the zirconia framework (ZIC group). All crowns were cemented on implant abutments, after which the specimens were tested for fracture resistance. The data were analyzed with the Kruskal-Wallis test and the Mann-Whitney U-test with the Bonferroni correction (α = 0.05). The following mean frac...