Generalized Class-E Power Amplifier With Shunt Capacitance and Shunt Filter (original) (raw)
Related papers
Analysis and Design a 2.5 GHz Class-E Power Amplifier in Two Configurations
There are two circuit configurations that commonly used for Class-E power amplifiers, the Infinite DC-feed or Shunt capacitor configuration and the Finite DC-feed or Shunt inductor. Albeit these circuit configurations are not essentially different, however they show different behavior and performance. In this paper we have compared these Class-E configurations at 2.5 GHz. For this purpose, we have designed two class-E circuits, one with Infinite DC-feed configuration and the other with Shunt inductor configuration. We have used the GaN High Electron Mobility Transistor (HEMT) in both designs. Optimized simulations showed 69% drain efficiency, 64% PAE, and 21.46 dBm load power, in the case of Infinite DC-feed design and 71% efficiency, 64.5% PAE, and 15.93 dBm load power in the case of Shunt inductor design. It is obvious that we should consider the importance of PAE inhigh power circuits and the importance of DE in low power circuits. The results propose that Infinite DC-feed design...
Efficient class-E power amplifier for variable load operation
2017 Integrated Nonlinear Microwave and Millimetre-wave Circuits Workshop (INMMiC), 2017
In this paper, a GaN HEMT class-E power amplifier (PA) has been designed for efficiently operating under variable load resistance at the 750 MHz frequency band. The desired zero voltage switching (ZVS) of the device can be approximated for a wide range of resistive loads, by means of a simple inductive impedance inverter, derived from [1]. The loadpull contours, obtained from simulations, allowed the drain terminating network to be properly adjusted in order to maximize the output power control while at the same time minimizing losses. Once the amplifier was implemented, an efficiency over 76% has been measured at 9.6 dB power back-off, with a peak of 85% at 50 Ω. In addition, the efficiency stays as high as 75% for a 150 MHz frequency range.
A 1GHZ CLASS E POWER AMPLIFIER FOR WIRELESS APPLICATIONS
In this paper, a class E power Amplifier (PA) suitable for wireless applications (Wi-Max, cellular phones, cordless phones etc,) is proposed by using the device of RF3931GaN HEMT (Gallium Nitrate High Electron Mobility Transistor).The proposed class E power Amplifier for achieving high output power and increasing gain up to 14.327dB and operates in the frequency range of 1GHz. The designed Power Added Efficiency (PAE) is 64% after optimization and the maximum source power achieved is 32dBw.
Investigation on technological aspects of class E RF power amplifiers for umts applications
This paper presents results of investigation on the effects of technology on the performance of the class E power amplifier circuit. A typical class E circuit has been designed and simulated, for a typical UMTS Tx frequency (1.95 GHz) and output power ( 27dBm). Three different technologies have been used (silicon BJT, CMOS and GaAs HBT) and several important parameters (output efficiency, power added efficiency, stress put on the device) have been monitored and put in table form for comparison. Care has been taken to adapt the design in such a way to provide a maximum performance with each technology, for a fair comparison. The results are then analyzed and different tradeoffs are discussed. Possibilities for the linearization of the amplifier are considered.
Design Method for UHF Class-E Power Amplifiers
2009 Annual IEEE Compound Semiconductor Integrated Circuit Symposium, 2009
This paper describes a method for designing singleended high-efficiency switched-mode class-E UHF power amplifiers. The design procedure consists of a modified load pull transistor characterization from which a power/efficiency metric is calculated. Results for four prototypes using different device technologies are presented in detail. Amplifiers with Si-LDMOS, SiC-MESFET, GaN-HEMT on a Si substrate, and GaN-HEMT on a SiC substrate produce power over 40W with power-added efficiency greater than 75% and gain between 13 dB and 17 dB.
High-Efficiency RF Pulsewidth Modulation of Class-E Power Amplifiers
IEEE Transactions on Microwave Theory and Techniques, 2011
A new switch mode power amplifier (SMPA) topology particularly suitable for energy efficient amplification of radio frequency pulse width modulation (RF-PWM) signals is derived. It is analytically shown that high efficiency can be maintained over a wide power dynamic range if the imaginary part of the Class-E load impedance is varied along with the duty cycle (pulse width). Using the theory developed, an explicit design procedure is presented that allows practical realization of the proposed topology from the circuit and component specifications. Following the design procedure, and using in-house (Chalmers University) SiC varactor diodes to implement the tunable imaginary load impedance, a 2 GHz 10 W peak output power GaN HEMT circuit demonstrator is realized. RF-PWM input signals for characterization of the prototype PA is generated with a dedicated 65 nm CMOS modulator. The measurements show that a drain efficiency > 70% can be obtained over an 6.5 dB dynamic range, which verifies the theory presented and demonstrates the feasibility of the proposed PA topology.
IET Circuits, Devices & Systems, 2016
In this study, design theory and analysis for the class E power amplifier (PA), considering the metal oxide semiconductor field effect transistor (MOSFET) parasitic input and output capacitances, are proposed. The input resistance and capacitances cause non-ideal input voltage at gate terminal, which affect the specifications of the class E PA. In the proposed study, non-linear drain-to-source, linear gate-to-drain and linear gate-to-source MOSFET parasitic capacitances are considered, while zero voltage and zero derivative switching conditions are achieved. Moreover, the input resistance and the value of the input voltage are taken into account in the design theory. According to the obtained results, the duty cycle of the MOSFET depends on the MOSFET threshold voltage, input voltage, input series resistance, and some other parameters, which will be explained in this study. A design example is finally given to describe the design procedure at 1 MHz operating frequency along with the experimental result. The circuit simulation is also performed using PSpice software. The measured results showed quantitative agreements with simulation and theory results.
Design of high efficiency class e power amplifier in l band
International Journal for Scientific Research and Development, 2015
In Modern Base station, at the transmitter side, a power amplifier is used to increase the signal power and allow longer distance transmission. The rapid growth in wireless communications and radar applications creates many challenges in performance of power amplifiers. Microwave L band is very useful in Long Distance Radar, Private Radio, Navigation system and Mobile communication so it is desirable to use high efficiency Power amplifier at transmitter side because most of power dissipation take place at active devices used in amplifier. In this paper Class E Switched mode topology is discussed because of high efficiency and low switching loss.
Analysis and design of class-E power amplifier considering MOSFET nonlinear capacitance
International Journal of Power Electronics and Drive Systems (IJPEDS), 2021
Class-E power amplifiers are integrated into many applications because their simple design and high performance. The efficiency of the power amplifier is significantly impacted by the nonlinear characteristic of the switching device, which is not analyzed clearly in theory. The nonlinear drain-tosource parasitic capacitance of the power transistor and the linear external capacitance are both contributed to the optimum conditions for obtaining the exact shunt capacitance. In this paper, a high-efficiency class-E power amplifier with shunt capacitance is designed with the consideration of both linear and nonlinear capacitance. Furthermore, a mathematical analysis is derived to calculate the component values in order to design the class-E power amplifier. Consequently, high power-added efficiency of 94.6% is obtained using MRF9030 MOSFET transistor with parameter of 4W output power and 13.56 MHz operating frequency. Finally, the measurement result of a linear class-E power amplifier circuit is obtained to compare and realize the efficiency of the proposed work.
Design of a 2 GHz GaAs HBT-based Class-E power amplifier
This paper presents a design procedure for the GaAs HBT-based Class-E power amplifier for 2 GHz. An empirical approach, based on load-pull and source-pull sim- ulations has been used to find an optimal impedance point for high efficiency operation. The simulation results show that a single-stage single-ended Class-E PA can achieve PAE higher than 70 %, output power of 24 dBm and transducer power gain of 15 dB when driven from a standard 50 Ohm signal generator. Three different solutions for the imple- mentation of the load network are discussed, including both lumped and distributed components. designed and implemented in various technologies and in different frequency bands. In many papers it is shown how the circuit deviates from its nominal operation when dif- ferent kinds of non-ideal effects are taken into account. These effects include finite-inductance DC-feeding coil, finite Q-factor of the load network, non-zero fall time of the collector/drain current, variations in duty c...