In vitro comparison of 3D printed polylactic acid/hydroxyapatite and polylactic acid/bioglass composite scaffolds: Insights into materials for bone regeneration (original) (raw)
Related papers
Biomedical Physics & Engineering Express, 2020
Autologous cancellous-bone grafts are the current gold standard for therapeutic interventions in which bone-regeneration is desired. The main limitations of these implants are the need for a secondary surgical site, creating a wound on the patient, the limited availability of harvest-safe bone, and the lack of structural integrity of the grafts. Synthetic, resorbable, bone-regeneration materials could pose a viable treatment alternative, that could be implemented through 3D-printing. We present here the development of a polylactic acid-hydroxyapatite (PLA-HAp) composite that can be processed through a commercial-grade 3D-printer. We have shown that this material could be a viable option for the development of therapeutic implants for bone regeneration. Biocompatibility in vitro was demonstrated through cell viability studies using the osteoblastic MG63 cell-line, and we have also provided evidence that the presence of HAp in the polymer matrix enhances cell attachment and osteogenic...
European Cells and Materials, 2021
The demand for bone grafting procedures in various fields of medicine is increasing. Existing substitutes in clinical practice do not meet all the criteria required for an ideal bone scaffold, so new materials are being sought. This study evaluated bone regeneration using a critical-size Wistar rat’s calvarial defect model. 12 male and 12 female rats were evenly divided into 3 groups: 1. Negative and positive (Geistlich Bio-Oss®) controls; 2. polylactic acid (PLA) and PLA/hydroxyapatite (HA); 3. PLA/HA cellularised with dental pulp stem cells (DPSC) and PLA/HA extracellular matrix (ECM) scaffolds. PLA/HA filament was created using hot-melt extrusion equipment. All scaffolds were fabricated using a 3D printer. DPSC were isolated from the incisors of adult Wistar rats. The defects were evaluated by micro-computed tomography (µCT) and histology, 8 weeks after surgery. µCT revealed that the Bio-Oss group generated 1.49 mm3 and PLA/HA ECM 1.495 mm3 more bone volume than the negative cont...
Molecules
Bio-based and patient-specific three-dimensional (3D) scaffolds can present next generation strategies for bone tissue engineering (BTE) to treat critical bone size defects. In the present study, a composite filament of poly lactic acid (PLA) and 45S5 bioglass (BG) were used to 3D print scaffolds intended for bone tissue regeneration. The thermally induced phase separation (TIPS) technique was used to produce composite spheres that were extruded into a continuous filament to 3D print a variety of composite scaffolds. These scaffolds were analyzed for their macro- and microstructures, mechanical properties, in vitro cytotoxicity and in vivo biocompatibility. The results show that the BG particles were homogeneously distributed within the PLA matrix and contributed to an 80% increase in the mechanical strength of the scaffolds. The in vitro cytotoxicity analysis of PLA-BG scaffolds using L929 mouse fibroblast cells confirmed their biocompatibility. During the in vivo studies, the popu...
Bone tissue engineering has been developed in the past decades, with the engineering of bone substitutes on the vanguard of this regenerative approach. PCL based scaffolds are fairly applied for bone regeneration, and several composites have been incorporated, as to improve the devices’ mechanical properties and tissue ingrowth. In this study, HA was incorporated on PCL based scaffolds with two different proportions, 80:20 and 60:40. Devices were produced with two different techniques, SC and MB, and further investigated with regards to their mechanical characteristics and in vitro cytocompatibility. Results show the MB devices to present more promising mechanical properties, along with the incorporation of HA. The latter is also related to an increase in osteogenic activity and promotion. Overall, this study suggest PCL:HA scaffolds to be promising candidates for bone tissue engineering, particularly when produced by the MB method.
Polymers, 2021
The 3D-printed bioactive ceramic incorporated Poly(ε-caprolactone) (PCL) scaffolds show great promise as synthetic bone graft substitutes. However, 3D-printed scaffolds still lack adequate surface properties for cells to be attached to them. In this study, we modified the surface characteristics of 3D-printed poly(ε-caprolactone)/hydroxyapatite scaffolds using O2 plasma and sodium hydroxide. The surface property of the alkaline hydrolyzed and O2 plasma-treated PCL/HA scaffolds were evaluated using field-emission scanning microscopy (FE-SEM), Alizarin Red S (ARS) staining, and water contact angle analysis, respectively. The in vitro behavior of the scaffolds was investigated using human dental pulp-derived stem cells (hDPSCs). Cell proliferation of hDPSCs on the scaffolds was evaluated via immunocytochemistry (ICC) and water-soluble tetrazolium salt (WST-1) assay. Osteogenic differentiation of hDPSCs on the scaffolds was further investigated using ARS staining and Western blot analys...
Materials Science and Engineering: C, 2021
Additive manufacturing (AM) has revolutionized the design of regenerative scaffolds for orthopaedic applications, enabling customizable geometric designs and material compositions that mimic bone. However, the available evidence is contradictory with respect to which geometric designs and material compositions are optimal. There is a lack of studies that systematically compare different pore sizes and geometries in conjunction with the presence or absence of calcium phosphates. We therefore evaluated the physicochemical and biological properties of additively manufactured scaffolds based on polylactic acid (PLA) in combination with hydroxyapatite (HA). HA was either incorporated in the polymeric matrix or introduced as a coating, yielding 15 and 2% wt., respectively. Pore sizes of the scaffolds varied between 200 and 450 μm and were shaped either triangularly or hexagonally. All scaffolds supported the adhesion, proliferation and differentiation of both primary mouse osteoblasts and osteosarcoma cells up to four weeks, with only small differences in the production of alkaline phosphatase (ALP) between cells grown on different pore geometries and material compositions. However, mineralization of the PLA scaffolds was substantially enhanced in the presence of HA, either embedded in the PLA matrix or as a coating at the surface level, and by larger hexagonal pores. In conclusion, customized HA/PLA composite porous scaffolds intended for the repair of critical size bone defects were obtained by a cost-effective AM method. Our findings indicate that the analysis of osteoblast adhesion and differentiation on experimental scaffolds alone is inconclusive without the assessment of mineralization, and the effects of geometry and composition on bone matrix deposition must be carefully considered in order to understand the regenerative potential of experimental scaffolds.
Materials, 2020
3D printed biomaterials have been extensively investigated and developed in the field of bone regeneration related to clinical issues. However, specific applications of 3D printed biomaterials in different dental areas have seldom been reported. In this study, we aimed to and successfully fabricated 3D poly (lactic-co-glycolic acid)/β-tricalcium phosphate (3D-PLGA/TCP) and 3D β-tricalcium phosphate (3D-TCP) scaffolds using two relatively distinct 3D printing (3DP) technologies. Conjunctively, we compared and investigated mechanical and biological responses on human dental pulp stem cells (hDPSCs). Physicochemical properties of the scaffolds, including pore structure, chemical elements, and compression modulus, were characterized. hDPSCs were cultured on scaffolds for subsequent investigations of biocompatibility and osteoconductivity. Our findings indicate that 3D printed PLGA/TCP and β-tricalcium phosphate (β-TCP) scaffolds possessed a highly interconnected and porous structure. 3D...
Journal of Biomedical Materials Research, 2001
Engineering new bone tissue with cells and a synthetic extracellular matrix (scaffolding) represents a new approach for the regeneration of mineralized tissues compared with the transplantation of bone (autografts or allografts). In the present work, highly porous poly(L-lactic acid) (PLLA) and PLLA/hydroxyapatite (HAP) composite scaffolds were prepared with a thermally induced phase separation technique. The scaffolds were seeded with osteoblastic cells and cultured in vitro. In the pure PLLA scaffolds, the osteoblasts attached primarily on the outer surface of the polymer. In contrast, the osteoblasts penetrated deep into the PLLA/HAP scaffolds and were uniformly distributed. The osteoblast survival percentage in the PLLA/HAP scaffolds was superior to that in the PLLA scaffolds. The osteoblasts proliferated in both types of the scaffolds, but the cell number was always higher in the PLLA/HAP composite scaffolds during 6 weeks of in vitro cultivation. Bone-specific markers (mRNAs encoding bone sialoprotein and osteocalcin) were expressed more abundantly in the PLLA/HAP composite scaffolds than in the PLLA scaffolds. The new tissue increased continuously in the PLLA/HAP composite scaffolds, whereas new tissue formed only near the surface of pure PLLA scaffolds. These results demonstrate that HAP imparts osteoconductivity and the highly porous PLLA/ HAP composite scaffolds are superior to pure PLLA scaffolds for bone tissue engineering.
Journal of Materials Science, 2019
The article presents a new methodology that employs 3D printing technology to generate a microporous composite material of polylactic acid, sodium alginate and hydroxyapatite, whose microstructure is designed by means of the 3Dnumerical solution from a mathematical model. This model represents the spatiotemporal dynamics of the interaction between osteoblasts and osteoclasts in the bone remodeling. The microporosity of composite material mimics the structure of human trabecular bone. This material has density with microporosity pretty close to the one that is exhibited by the natural bone tissue. Close relationship between the material processing and its elasticity module is observed. When subjecting this composite material to a simulated body fluid treatment, the mechanical resistance to compression is increased due to induced mineralization of hydroxyapatite crystals on its surface. The methodology shows potential to generate structures that allow the control of the composite material properties. The material presents a microporosity that has morphological and chemical properties suitable for future applications in tissue engineering as bone scaffold.
Hydroxyapatite scaffolds for bone tissue engineering made by 3D printing
Journal of Materials Science: Materials in Medicine, 2005
Nowadays, there is a significant need for synthetic bone replacement materials used in bone tissue engineering (BTE). Rapid prototyping and especially 3D printing is a suitable technique to create custom implants based on medical data sets. 3D printing allows to fabricate scaffolds based on Hydroxyapatite with complex internal structures and high resolution. To determine the in vitro behaviour of cells cultivated on the scaffolds, we designed a special test-part. MC3T3-E1 cells were seeded on the scaffolds and cultivated under static and dynamic setups. Histological evaluation was carried out to characterise the cell ingrowth. In summary, the dynamic cultivation method lead to a stronger population compared to the static cultivation method. The cells proliferated deep into the structure forming close contact to Hydroxyapatite granules. C 2005 Springer Science + Business Media, Inc.