Design of Single-Feed Reflectarray Antennas With Asymmetric Multiple Beams Using the Particle Swarm Optimization Method (original) (raw)
Related papers
Optimization Approach to Design Single Feed Symmetric and Asymmetric Multibeam Reflectarrays
Frequenz, 2014
A novel optimization method to design the layout of printed reflectarrays for multibeam operation is presented in this paper. The proposed approach allows using different classes of cell elements to design the layout of reflectarrays. Therefore, phase curves do not have to fulfill the requirement of having a phase range wider than 360°. The dimensions of each cell element are adjusted to achieve the required phase distribution to radiate symmetric or asymmetric multiple beams. Five different reflectarrays have been designed by using this technique. Numerical simulations demonstrate high gain performance and low side lobe levels.
IEEE Antennas and Propagation Magazine, 2019
This paper presents some recent developments in multiple beam antennas (MBAs) based on reflectarrays for communication satellites in K-and Ka-bands. The existing high throughput satellites commonly employ four reflector antennas to provide cellular coverage formed by multiple spot beams in a four color scheme. Reflectarray antennas are proposed as an attractive solution for the design of novel MBA configurations to produce multi-spot coverage with a smaller number of apertures than conventional MBA systems based on reflector technology. Single and dual reflectarray configurations have been considered for this purpose, exploiting the reflectarrays' ability to produce independent beams in different polarizations and frequencies.
Design and Experiment of a Single-Feed Quad-Beam Reflectarray Antenna
IEEE Transactions on Antennas and Propagation, 2012
Reflectarray antennas show momentous promise as a cost-effective high-gain antenna, capable of generating multiple simultaneous beams. A systematic study on various design methods of single-feed multi-beam reflectarray antennas is presented in this communication. Two direct design methods for multi-beam reflectarrays, geometrical method and superposition method, are investigated first. It is demonstrated that although both methods could generate a multi-beam radiation pattern, neither approach provides satisfactory performance, mainly due to high side-lobe levels and gain loss in these designs. The alternating projection method is then implemented to optimize the phase distribution on the reflectarray surface for multi-beam performance. Mask definition and convergence condition of the optimization are studied for multi-beam reflectarray designs. Finally a Ka-band reflectarray prototype is fabricated and tested which shows a good quad-beam performance.
Optimum Design of Broad-Beam Microstrip Reflectarray
2007
The reflectarray's elements arrangement for generating an arbitrary phase distribution in the antenna aperture and thus a wide beamwidth of far field pattern are presented. The desired phase delay of reflectarray elements, which are duplicated the same radiating aperture as parabolic backscatters, are determined on the construction of the curvature of a shaped backscatter surface with the help of Snell's law for beam forming to cover a broad area. The method of moment (MoM) and the infinite-array are applied to calculate reflection phase characteristic. The optimized feed distance is calculated from the aperture efficiency with considering feed blockage efficiency and has investigated the influence of the feed position on the -3 dB beamwidth and gain performance. Having confirmed the validity of this approach, the X-band antenna prototype is designed and developed. This reflectarray is tested experimentally and shows good performance.
Analysis of dual-reflector antennas with a reflectarray as subreflector
IEEE Antennas and Propagation Magazine, 2000
In this paper, a modular technique is described for the analysis of dual-reflector antennas using a reflectarray as a subreflector. An antenna configuration based on a sub-reflectarray and a parabolic main reflector provides better bandwidth than a single reflectarray, and has a number of advantages compared with a conventional dual-reflector antenna. Examples include the possibility of beam shaping by adjusting the phase on the sub-reflectarray, and potential capabilities to scan or reconfigure the beam. The modular technique implemented for the antenna analysis combines different methods for the analysis of each part of the antenna. First, the real field generated by the horn is considered as the incident field on each reflectarray element. Second, the reflectarray is analyzed with the same technique as for a single reflectarray, i.e., considering local periodicity and the real angle of incidence of the wave coming from the feed for each periodic cell. Third, the main reflector is analyzed using the Physical Optics (PO) technique, where the current on the reflector surface is calculated by summing the radiation from all the reflectarray elements. Finally, the field is calculated on a rectangular periodic mesh at a projected aperture, and then a time-efficient fast Fourier transform (FFT) algorithm is used to compute the radiation pattern of the antenna. The last step significantly improves the computational efficiency. However, it introduces a phase error, which reduces the accuracy of the radiation patterns for radiation angles far away from the antenna's axis. The phase errors have been evaluated for two integration apertures. It has been demonstrated that accurate patterns are obtained in an angular range of ±6°, which is sufficient for large reflectors. The method of analysis has been validated by comparing the results with simulations obtained from GRASP8. Finally, the theoretical beam-scanning performance of the antenna is analyzed.
Recent Developments of Reflectarray Antennas in Dual-Reflector Configurations
International Journal of Antennas and Propagation, 2012
Recent work on dual-reflector antennas involving reflectarrays is reviewed in this paper. Both dual-reflector antenna with a reflectarray subreflector and dual-reflectarrays antennas with flat or parabolic main reflectarray are considered. First, a general analysis technique for these two configurations is described. Second, results for beam scanning and contoured-beam applications in different frequency bands are shown and discussed. The performance and capabilities of these antennas are shown by describing some practical design cases for radar, satellite communications, and direct broadcast satellite (DBS) applications.
Recent advances in beam-scanning reflectarray antennas
2014 XXXIth URSI General Assembly and Scientific Symposium (URSI GASS), 2014
A review of the recent advances in beam-scanning reflectarray antennas is presented in this paper. First, an overview of the two different methodologies for designing beam-scanning reflectarray antennas, namely aperture phase tuning and feed tuning techniques, is presented, and the advantages and limitations of both approaches are delineated. Next, recent developments in feed-tuned beam-scanning reflectarray antennas such as multifocal and partially illuminated apertures are reviewed and some numerical and experimental results are presented and compared. In comparison with other alternatives such as phase-tuned reflectarrays or phased array antennas, these passive beamscanning reflectarrays are low cost and less complex, which makes them suitable choices for the new generation of high-gain beam-scanning antennas.
Sensors, 2020
Broadband communication satellites in Ka-band commonly use four reflector antennas to generate a multispot coverage. In this paper, four different multibeam antenna farms are proposed to generate the complete multispot coverage using only two multibeam reflectarrays, making it possible to halve the number of required antennas onboard the satellite. The proposed solutions include flat and curved reflectarrays with single or dual band operation, the operating principles of which have been experimentally validated. The designed multibeam reflectarrays for each antenna farm have been analyzed to evaluate their agreement with the antenna requirements for real satellite scenarios in Ka-band. The results show that the proposed configurations have the potential to reduce the number of antennas and feed-chains onboard the satellite, from four reflectors to two reflectarrays, enabling a significant reduction in cost, mass, and volume of the payload, which provides a considerable benefit for s...
IEEE Transactions on Antennas and Propagation, 2021
This contribution describes the design of a multibeam parabolic reflectarray to produce two adjacent beams per feed in orthogonal Circular Polarization (CP) simultaneously at transmit (Tx) and receive (Rx) frequencies in Ka-band. The Variable Rotation Technique (VRT) has been applied to reflectarray cells based on two types of resonant elements, which makes it possible to provide orthogonal beams at Tx and Rx, as well as to implement an in-band optimization procedure to reduce the cross-polarization. A 90-cm parabolic reflectarray has been designed, manufactured and tested to produce multiple adjacent beams in RHCP and LHCP at both 20 and 30 GHz. The results are satisfactory and validate the concept of generating two spaced beams in orthogonal CP by a single feed, changing the polarization of the beam between Tx and Rx. This concept can be suitable for multispot satellites in Ka-band, enabling to halve the number of onboard antennas and feeds.