Performance Assessment of a Large Internal Combustion Engine Due to Inlet Air Cooling and Dehumidification: GT-Power Software Simulation (original) (raw)
Related papers
Development of Mathematical Model for Cooling of Internal Combustion Engines
ABSTACT: The energy released in the combustion chamber of an internal combustion engine is dissipated in three different ways. About 35 % of the fuel energy is converted to useful crankshaft work, and about 30 % energy is expelled with the exhaust. This leaves about one-third of the total energy that must be transmitted from the enclosed cylinder through the cylinder walls and head to the surrounding atmosphere. The heat generated in the combustion chamber which is transferred to the engine body is cooled down to a reasonable temperature (that permits the continuous operation of the engine) basically for three reasons; firstly to promote a high volumetric efficiency, secondly to ensure proper combustion and thirdly to ensure mechanical operation and reliability. Non continuous cooling of the engine while in operation leads to overheating of the engine. This can affect the mechanical performances of an engine. Firstly, overheating can lead to a loss of strength. Secondly, the top piston ring groove temperature must also be limited to about 200 0 C if the lubrication is to remain satisfactory. Above this temperature, lubricants can degrade, leading to both a loss of lubrication, and packing of the piston ring groove with products from the decomposed oil. Finally, failure can result through thermal strain. Strain can be caused by either mechanical or thermal loading. The thermal strain is directly proportional to the temperature gradient. This has led to the development of mathematical model for cooling of spark ignition internal combustion engines. The mathematical model was simulated to estimate the thermal system response for the user specified input heat profile, Q in. The maximum heat input supplied to the system is approximately 1800 watts. This magnitude is substantially below the energy released during the actual engine combustion process. The engine, radiator, and junction node temperatures plotted against time for a series of symmetrical 10.0°C disturbances in the temperature set point. For the selected controller gains, the engine temperature displays small steady-state departures from the set point temperature of approximately 0.9°C. The junction temperature profile is very similar to the engine temperature as expected. The radiator temperature changes slightly which reflects the large thermal exhaust capabilities for this node.
Thermodynamic Analysis of Two-Stage Turbocharging for Diesel Engine
Turbochargers are used in automotive industry to enhance the power output of an internal combustion (IC) engines. The useful applications of such a turbocharger are in the engines for the reduction of engine size and fuel consumption by increasing existing power output. It is because of these reasons turbochargers are now becoming more popular in automobile applications. It is also used where compensation of altitude requires and for boosting of the engine power. Single stage turbocharger is not recovered all the heat of the exhaust therefore it is decided to use two stage turbocharging. Two stage turbocharging is used to recover all the heat of exhaust and to develop the more power from the engine. The present study is based on the improvement of the engine power of the existing diesel engine. This is then compared with naturally aspirated engine and engine with single stage turbocharging. In the present study the operating parameters are discussed and compared. It is observed that Brake mean effective pressure (BMEP) and Brake specific fuel consumption (BSFC) are increased irrespective of the speed of the engine. The rises in volumetric efficiencies are observed in the existing engine and thereby rise in brake thermal efficiencies.
SAE Technical Paper Series, 2005
This paper describes some recent advances in the field of I.C. engine modeling and simulation, concerning the development and application of a 1D thermo-fluid dynamic research code. An extensive experimental analysis has been concurrently carried out, to support the development and validation of the simulation code. A four-stroke, 10V-cylinder, 5.0 liters automotive S.I. engine has been modeled, in order to predict not only the wave motion in the system and its influence on the cylinder gas exchange process, but also the in-cylinder pressure to get a good prediction of pollutant emission concentration along the exhaust system. The gas composition in the exhaust pipe system is dictated by the cylinder discharge process, after the calculation of the combustion process via a thermodynamic multi-zone model, based on a fractal approach to predict the turbulent combustion. New kinetic mechanisms have been introduced to improve the prediction of NO and CO engine emissions; moreover, a new approach has been implemented, based on a scavenging model, to improve the calculation of engine HC emissions. Predicted results concerning volumetric efficiency, pressure losses, pressure pulses and gas compositions in the exhaust system have been compared with experimental measurements carried out on a configuration of a Lamborghini V10, 5.0 L automotive S.I. engine. These results have pointed out a satisfactory agreement in terms of volumetric efficiency, pressure trends inside the cylinder and exhaust gas composition.
Development of Off-Design Turbocharger Modelling Combined with 1-D Engine Model
Procceedings of the 18th Brazilian Congress of Thermal Sciences and Engineering, 2020
The present work aims to carry out an off-design turbocharger modelling powered by exhaust gases from a Wärtsilä 20V34SG engine. First of all, 1-D engine model was already developed in GT-Power software while considering a thermodynamic turbocharger modelling with constant isentropic efficiencies. Secondly, by using the results from 1-D engine model, the off-design turbocharger modelling is calibrated separately in EES software, taking into account compressible assumption, triangle velocities and geometric dimensions. The case study is derived from a R&D project (ANEEL PD-06483-0318/2018) that targets to cool and dehumidify the intake air at compressor's upstream through a cooling coil, thereby allowing engine's operation at reduced knocking conditions. The brake mean effective pressure (BMEP) is varied in the range of 20 to 23.45 bar, corresponding to brake power from 8.7 to 10.2 MW, respectively. With the off-design turbocharger modelling it is possible to analyze its operational behavior under higher BMEP, hence, allowing to predict some important parameters. The results showed that the turbocharger is operating within the manufacturer's limit for BMEP of 23.45 bar, presenting total-to-static isentropic efficiencies of 0.81 and 0.784 for compressor and turbine, respectively, rotational speed around 28135 RPM, pressure ratio at compressor of 4.567 and maintaining control on waste-gate valve.
Impact of the Heat Transfer on the Performance Calculations of Automotive Turbocharger Compressor
Oil & Gas Science and Technology – Revue d’IFP Energies nouvelles, 2011
Influence des transferts thermiques sur le calcul des performances des compresseurs de suralimentation-En général, les turbocompresseurs pris en compte dans les logiciels de simulation moteur sont modélisés de façon adiabatique. Cependant, les tests expérimentaux effectués au laboratoire montrent que ce n'est pas toujours le cas. L'utilisation directe des champs de fonctionnement fournis par les constructeurs de turbomachines n'est alors plus possible. Une évaluation quantitative de ces transferts, basée sur des tests réalisés sur un banc d'essais turbo à air chaud, est présentée. Puis ils sont pris en compte afin de calculer les caractéristiques réelles de fonctionnement d'un compresseur. La différence avec le modèle adiabatique apparaît très importante pour les faibles puissances compresseur. Ceci correspond aux faibles charges moteur.
A coupled approach for vehicle brake cooling performance simulations
International Journal of Thermal Sciences, 2018
Advances of CFD methods together with the constant growth of computer capacity enables simulations of complex coupled fluid and thermal problems. One such problem is the evaluation of brake cooling performance. The brake system is a critical component for passenger vehicles and ensuring correct brake operation under all possible load scenarios is a safety issue. An accurate prediction of convection, conduction and radiation heat fluxes for such a complicated system is challenging from modelling as well as numerical efficiency perspectives. This study describes a simulation procedure developed to numerically predict brake system component temperatures during a downhill brake performance test. Such tests have stages of forced and natural convection, and therefore, the airflow is influenced by the temperature changes within the system. For the numerical simulation, a coupled approach is utilised by combining aerodynamic and thermal codes. The aerodynamic code computes the convective heat transfer using a fully-detailed vehicle model in the virtual wind tunnel. The thermal code then uses this data and combines it with conduction and radiation calculations to give an accurate prediction of the component temperatures, which are subsequently used for airflow recalculation. The procedure is described in considerable detail for most parts of the setup. The calculated temperature history results are validated against experimental data and show good agreement. The method allows detailed investigations of distribution and direction of the heat fluxes inside the system, and of how these fluxes are affected by changes in material properties as well as changes in parts within or outside the brake system. For instance, it is shown that convection and especially convection from the inner vanes is the main contributor for the heat dissipation from the brake disk. Finally, some examples of how changing the vehicle design affects the brake cooling performance are also discussed.
Performance Improvement of a 43 MW Class Gas Turbine Engine with Inlet Air Cooling
International Journal of Emerging Trends in Engineering Research (IJETER), 2021
In this study, a process of inlet air cooling was implemented in the intake of a land-based gas turbine engine for electricity generation. The motivation behind the study is to improve the performance of the gas turbine engine in hot climate conditions,which causes a significant decrease in the output power and an increase in specific fuel consumption. For inlet air cooling, a refrigeration cycle was attached to the turbo-shaft gas turbine engine,and power required by the refrigeration is extracted from the mechanical engine power output of the gas turbine. A 43 MWclass gas turbine engine which is similar totheGeneral Electric LM6000 engine was modeled in this study. Considering an average coefficient of performance of 3.0 for a refrigeration system, the inlet cooling provided (by supplying cooled inlet air at 15oC) a 22.21% net power increase anda5.2% power specific fuel consumption improvement at 55oCambient conditions.