Structural, Microstructural and Compositional Changes of the AISI 314 Steel Used in the Sintering Furnace Belt Depending on the Operating Time (original) (raw)

New Alloying Systems for Sintered Steels: Critical Aspects of Sintering Behavior

Metallurgical and Materials Transactions A, 2014

Following the progress of sintering in steel powder compacts through original experiments

Sylvie Bordere

2003

Mechanical and Physical Properties of Differently Alloyed Sintered Steels as a Function of the Sintering Temperature

2021

Wear behaviour of sintered steels obtained using powder metallurgy method

Süleyman GÜNDÜZ

Mechanics, 2017

Editor's Page Iron Ore Sintering Part 1. Theory and Practice of the Sintering Process Sinterización De Minerales De Hierro Parte 1. Teoría y Práctica Del Proceso

2013

Iron ore sintering. Part 1. Theory and practice of the sintering process

Dyna (Medellin, Colombia)

Effect of Austempering Conditions on the Microstructure and Tensile Properties of Low Alloyed Sintered Steel

J. Torralba-Estelles

Metallurgical and Materials Transactions A, 2010

2D and 3D SIMS investigations on sintered steels

Jürgen Zwanziger

Applied Surface Science, 2005

Effects of milling time and temperature on phase evolution of AISI 316 stainless steel powder and subsequent sintering

Reza Esmaeilzadeh

Journal of Alloys and Compounds, 2018

Factors Infl uencing Mechanical Properties of Sintered Steels : Density and Carbon Content

NURAY BEKÖZ ÜLLEN

2019

An Introduction to the Metallurgy of Steels and its Alloys

Rob Francis

2017

Iron Ore Sintering Part 1. Theory and Practice of the Sintering Process Sinterización De Minerales De Hierro

2015

Influence of atmosphere on sintering of T15 and M2 steel powders

Fernando Fernandez

Metallurgical Transactions A, 1992

Sintered Fe-Mn-Si-C Steels

Janusz Konstanty

2019

Deformation, densification, and corrosion studies of sintered powder metallurgy plain carbon steel preforms

Ramaswamy Chandramouli

Materials & Design, 2007

Sintering of AISI M₂ High Speed Steel with the Addition of NbC

ELIAS LIDIONE DA SILVA

Materials Science Forum, 2012

Production and characterization of dual-phase steels from an AISI 8620 steel with high Mn content

Dayi Gilberto Agredo Diaz

Dyna, 2021

The Role of Oxygen Transfer in Sintering of Low Alloy Steel Powder Compacts: A Review of the “Internal Getter” Effect

JOM, 2016

Iron Ore Sintering: Raw Materials and Granulation

Mineral Processing and Extractive Metallurgy Review, 2016

Physical Metallurgy of Steel-Basic Principles

Dr R N Ghosh

XXX-X-XXXX-XXXX-X/XX/$XX.00 ©20XX IEEE The Influence of Intercritical Annealing Holding Time on Mechanical Properties of AISI 4340 Steel

Cecep Ruskandi

Sinterability and microstructure formation of a Hadfield steel produced by MIM

Renan Schroeder

EURO PM 2013 - European Powder Metallurgy Congress & Exhibition, 2013

IJERT-Barrelling Aspects and Microstructure Examination of Sintered AISI 8620 P/M Steel during Hot Upset Powder Preform Forging

IJERT Journal

International Journal of Engineering Research and Technology (IJERT), 2014

Influence of Geometry and Cooling Rate on Properties of Sinter-Hardened Steels

Marco Grande

Acta Metallurgica Slovaca, 2013

Barrelling Aspects and Microstructure Examination of Sintered AISI 8620 P/M Steel during Hot Upset Powder Preform Forging

YG Bala

2014

Critical Aspects of Alloying of Sintered Steels with Manganese

Eva Dudrova

Metallurgical and Materials Transactions A, 2010

Utilisation of sinter-hardening treatment for various sintered steels

Zbigniew Brytan

Journal of achievements in materials and manufacturing engineering, 2007

Lean sintered steels obtained through the master alloy route: mechanical properties

Monica campos

Transient Liquid Phase Sintering of PM Steel—A Matter of the Heating Rate

Metals

Analysis of the Properties and Characteristics Obtained from the Process Sinter Forging Steel

André Carvalho Tavares

2013