Resonance wave pumping with surface waves (original) (raw)
Related papers
Energy Harvesting Using Wake-Induced Vibration: Experiment in Circulating Water Channel
2015
In this study, the performance of an energy-harvesting device using wake-induced vibration is examined. An experimental setup was constructed that included a submerged cylinder vibrated by vortex-induced forces and a generator driven by the motion of the cylinder. We determined the diameter of the cylinder to optimize the range of Reynolds numbers to maximize the lift force acting on the cylinder and placed a fixed cylinder near the moving one to increase the range of synchronization and the amplitude. The measurement results showed that these design features can increase the energy conversion efficiency.
Oscillating U-Shaped Body for Underwater Piezoelectric Energy Harvester Power Optimization
Micromachines
Vibration energy harvesting (VeH) techniques by means of intentionally designed mechanisms have been used in the last decade for frequency bandwidth improvement under excitation for adequately high-vibration amplitudes. Oil, gas, and water are vital resources that are usually transported by extensive pipe networks. Therefore, wireless self-powered sensors are a sustainable choice to monitor in-pipe system applications. The mechanism, which is intended for water pipes with diameters of 2–5 inches, contains a piezoelectric beam assembled to the oscillating body. A novel U-shaped geometry of an underwater energy harvester has been designed and implemented. Then, the results have been compared with the traditional circular cylinder shape. At first, a numerical study has been carried at Reynolds numbers Re = 3000, 6000, 9000, and 12,000 in order to capture as much as kinetic energy from the water flow. Consequently, unsteady Reynolds Averaged Navier–Stokes (URANS)-based simulations are c...
A hybrid piezoelectric–electromagnetic nonlinear vibration energy harvester excited by fluid flow
Comptes Rendus. Mécanique
Energy harvesting mechanisms can be used to extract energy from ambient surroundings to power small electronic devices, which has a significant advantage in realizing self-sustaining wireless devices. The proposed design of this study uses the internal fluid flow within a pipe and takes advantage of the fluidstructure interaction through flow-induced vibration of a bluff body. The hybrid harvester uses the vibration to convert electrical energy through a piezoelectric material and an electromagnetic oscillator that can be tuned to resonate at the oscillation frequency. A numerical solver was used to estimate harvestable voltage for this submerged hybrid energy harvester model by using ordinary differential equations. A computational study was used to optimize the performance of the bluff bodies under the influence of the vortices for circular, triangular, ellipse, and quadrilateral shapes. Wake development was seen in the circular and triangular shapes with the ellipse having the lowest turbulence kinetic energy among the shapes. Structural deflection of the beam under resonance was compared for the different shapes, which displayed better results for triangular and elliptical bluff bodies.
Energy harvesting from hydraulic pressure fluctuations
Smart Materials and Structures, 2013
State-of-the-art hydraulic hose and piping systems employ integral sensor nodes for structural health monitoring to avoid catastrophic failures. Energy harvesting in hydraulic systems could enable self-powered wireless sensor nodes for applications such as energy-autonomous structural health monitoring and prognosis. Hydraulic systems inherently have a high energy intensity associated with the mean pressure and flow. Accompanying the mean pressure is the dynamic pressure ripple, which is caused by the action of pumps and actuators. Pressure ripple is a deterministic source with a periodic time-domain behavior conducive to energy harvesting. An energy harvester prototype was designed for generating low-power electricity from pressure ripples. The prototype employed an axially-poled off-the-shelf piezoelectric stack. A housing isolated the stack from the hydraulic fluid while maintaining a mechanical coupling allowing for dynamic-pressure-induced deflection of the stack. The prototype exhibited an off-resonance energy harvesting problem since the fundamental resonance of the piezoelectric stack was much higher than the frequency content of the pressure ripple. The prototype was designed to provide a suitable power output for powering sensors with a maximum output of 1.2 mW. This work also presents electromechanical model simulations and experimental characterization of the piezoelectric power output from the pressure ripple in terms of the force transmitted into the harvester.
Investigating the pumping process of a resonance-vibrating pump for medium-depth boreholes
Research in Agricultural Engineering, 2008
This paper deals with the pumping process of a resonance-vibrating pump, which utilizes the resonance vibrations of one degree-of-freedom oscillating system. The pump is powered by a mechanical shaker consisting of two counter rotating offset masses and operating in resonance. The study investigates the nature of the pumping process and conditions required to achieve pumping action. Equations for the flow rate, pressure developed at ground level or any height above it, the pump efficiency, and the power delivered by the shaker are derived. The analysis of the pumping process revealed that the flow rate of the pump may be maximized either by increasing the acceleration imparted on the oscillating system, and/or by reducing the resonance frequency. It was found that the pressure developed by the pump is independent of the depth of pumping, provided that the same acceleration is imparted, and its efficiency may be increased either by reducing the resonance frequency and/or by increasin...
Computational studies of resonance wave pumping in compliant tubes
Journal of Fluid Mechanics, 2008
The valveless impedance pump is a simple design that allows the producion or amplification of a flow without the requirement for valves or impellers. It is based on fluid-filled flexible tubing, connected to tubing of different impedances. Pumping is achieved by a periodic excitation at an off-centre position relative to the tube ends. This paper presents a comprehensive study of the fluid and structural dynamics in an impedance pump model using numerical simulations. An axisymmetric finite-element model of both the fluid and solid domains is used with direct coupling at the interface. By examining a wide range of parameters, the pump's resonance nature is described and the concept of resonance wave pumping is discussed. The main driving mechanism of the flow in the tube is the reflection of waves at the tube boundary and the wave dynamics in the passive tube. This concept is supported by three different analyses: (i) time-dependent pressure and flow wave dynamics along the tube...
Modeling of a Novel Submerged Oscillating Water Column (SOWC) Energy Harvester
2019
Wave energy converters (WEC) are hydraulic structures that are used to harvest energy from oceans. This research explores a new concept of a WEC termed a Submerged Oscillating Water Column (SOWC). Numerical simulations using the Computational Fluid Dynamics (CFD) code Flow-3D and physical model tests were carried out at Idaho State University to assess the validity and efficiency of the proposed device. The SOWC device consists of two submerged chambers that are connected to allow airflow between the two as waves pass; ideally spaced at half a wavelength. The results of the CFD modeling for seventeen different geometries with linear waves were investigated. The model was validated with experimental tests in a flume and the efficiency of the device calculated. The influence of four parameters: water depth, wave height, period and the size of SOWC were investigated. The numerical CFD modeling indicates the ratio of water elevation movement inside the chambers can be up to 80% of wave ...
Wave Energy-Driven Resonant Sea-Water Pump
Journal of Offshore Mechanics and Arctic Engineering, 1997
A wave-driven sea-water pump which operates by resonance is described. Oscillations in the resonant and exhaust ducts perform similar to two mass-spring systems coupled by a third spring acting for the compression chamber. Performance of the pump is optimized by means of a variable volume air compression chamber (patents pending) which tunes the system to the incoming wave frequency. Wave tank experiments with an instrumented, 1:20-scale model of the pump are described. Performance was studied under various wave and tuning conditions and compared to a numerical model which was found to describe the system accurately. Successful sea trials at an energetic coastline provide evidence of the system’s viability under demanding conditions.
2017
As a result of the studies performed on the wave energy resource worldwide, a research project was set up to harvest wave energy for its conversion into electrical energy. Within this framework, a theoretical model of the electromechanical energy harvesting system, developed with MATLAB's Simulink software, will be provided. This tool recreates the site conditions where the device will be installed and offers valuable information about the amount of energy that can be harnessed. This research provides a deeper understanding of the utilization of wave energy in order to improve the efficiency of a 1:1 scale prototype of the device.
Energy extraction from the motion of an oscillating water column
Ocean Systems Engineering, 2013
An Oscillating Water Column (OWC) is a relatively practical and convenient device that converts wave energy to a usable form, which is electricity. The OWC is kept inside a fixed truncated vertical cylinder, which is a hollow structure with one open end submerged in the water and with an air turbine at the top. This research adopts potential theory and Galerkin methods to solve the fluid motion inside the OWC. Using an air-water interaction model, OWC design for energy extraction from regular wave is also explored. The hydrodynamic coefficients of the scattering and radiation potentials are solved for using the Galerkin approximation. The numerical results for the free surface elevation have been verified by a series of experiments conducted in the University of New Orleans towing tank. The effect of varying geometric parameters on the response amplitude operator (RAO) of the OWC is studied and modification of the equation for evaluating the natural frequency of the OWC is made. Using the model of air-water interaction under certain wave parameters and OWC geometric parameters, a computer program is developed to calculate the energy output from the system.