Surface Functionalization of Fluorine-Doped Tin Oxide Samples through Electrochemical Grafting (original) (raw)
Related papers
ACS applied materials & interfaces, 2014
Both optical and electrochemical graphene-based sensors have gone through rapid development, reaching high sensitivity at low cost and with fast response time. However, the complex validating biochemical operations, needed for their consistent use, currently limits their effective application. We propose an integration strategy for optoelectrochemical detection that overcomes previous limitations of these sensors used separately. We develop an optoelectrochemical sensor for aptamer-mediated protein detection based on few-layer graphene immobilization on selectively modified fluorine-doped tin oxide (FTO) substrates. Our results show that the electrochemical properties of graphene-modified FTO samples are suitable for complex biological detection due to the stability and inertness of the engineered electrodic interface. In addition, few-layer immobilization of graphene sheets through electrostatic linkage with an electrochemically grafted FTO surface allows obtaining an optically acc...
Chemosensors
Various forms of zinc oxide (ZnO) are frequently used in the design of optical and electrochemical sensors. However, the optical and electrochemical properties of ZnO should be properly adjusted depending on the application area. Therefore, in this work, we have investigated changing/tuning the properties of ZnO by depositing a layer of polydopamine (PDA) on its surface. In order to perform this investigation, the surface of fluorine-doped tin oxide (FTO) was modified with the layer of ZnO nanorods and PDA. ZnO nanorods were synthesized by hydrothermal synthesis technique, and after the synthesis, they were coated with polydopamine exploiting the self-polymerization of dopamine. The nanostructures were investigated by using electrochemical and optical methods. Electrochemical impedance spectroscopy measurements showed that electrochemical properties of FTO-ZnO and FTO-ZnO-PDA nanostructures could be changed by the variation of both—applied electrical potential and/or exposition towa...
Tin Oxide Nanosheet Assembly for Hydrophobic/Hydrophilic Coating and Cancer Sensing
ACS Applied Materials & Interfaces, 2012
Tin oxide nanosheets were crystallized on transparent conductive oxide substrates of fluorine-doped tin oxide in aqueous solutions. The nanosheets had chemical ratio of Sn:O:F = 1:1.85:0.076, suggesting fluorine doping into SnO 2. They were hydrophobic surfaces with contact angle of 140°. They were converted to hydrophilic surfaces with contact angle of below 1°by light irradiation. The simple water process will be applied to surface coating of polymers, metals, biomaterials, papers, etc. Furthermore, the tin oxide nanosheets were modified with dye-labeled monoclonal antibody. Monoclonal antibody reacts with human alphafetoprotein in blood serum of hepatocellular cancer patient. Photoluminescence and photocurrent were obtained from the nanosheets under excitation light. Photoelectric conversion was an essence in the sensing system. The tin oxide nanosheets with dye-labeled prostate specific antigen will be used for electrodes of prostate cancer sensors.
Coatings
Coatings of hierarchically meso-macroporous antimony-doped tin oxide (ATO) enable interfacing adsorbed species, such as biomacromolecules, with an electronic circuit. The coating thickness is a limiting factor for the surface coverage of adsorbates, that are electrochemically addressable. To overcome this challenge, a carbon black-based templating method was developed by studying the composition of the template system, and finding the right conditions for self-standing templates, preventing the reaction mixture from flowing out of the mask. The thicknesses of as-fabricated coatings were measured using stylus profilometry to establish a relationship between the mask thickness and the coating thickness. Cyclic voltammetry was performed on coatings with adsorbed cytochrome c to check whether the entire coating thickness was electrochemically addressable. Further, bacterial photosynthetic reaction centers were incorporated into the coatings, and photocurrent with respect to coating thickness was studied. The template mixture required enough of both carbon black and polymer, roughly 7% carbon black and 6% poly(ethylene glycol). Coatings were fabricated with thicknesses approaching 30 µm, and thickness was shown to be controllable up to at least 15 µm. Under the experimental conditions, photocurrent was found to increase linearly with the coating thickness, up to around 12 µm, above which were diminished gains.
Fluorine-doped tin oxide surfaces modified by self-assembled alkanethiols for thin-film devices
Applied Surface Science, 2013
In this work, we have investigated self-assembled monolayers (SAMs) from alkanethiols on fluorinedoped tin oxide (FTO) surfaces, which were used as an anode for thin-film devices prepared from the conductive copolymer so-called sulfonated poly(thiophene-3-[2-(2-methoxyethoxy) ethoxy]-2,5-diyl) (S-P3MEET). The assembled monolayers were characterized by using wetting contact angle, atomic force microscopy, and electrical measurements. The results indicated that dodecanethiol molecules, CH 3 (CH 2) 11 SH, were well assembled on the FTO surfaces. In addition, it was found similar values of wetting contact angle for dodecanethiol assembled on both FTO and Au surfaces. Concerning the thin-film device, current-voltage analysis revealed a hysteresis. This behavior was associated to a charge-trapping effect and also to structural changes of the SAMs. Finally, charge injection capability of tin oxide electrodes can be improved by using SAMs and then this approach can plays an important role in molecular-scale electronic devices.
Canadian Journal of Chemistry, 2022
Transparent conductive oxides such as indium tin oxide (ITO) substrates are commonly employed as prime materials for optoelectronic applications. Enhancement in functions of such devices often compels stable and robust modification of the ITO substrate to improve its interfacial charge transfer characteristics. Thereby, in this work, naphthyl modifier multilayer films are fabricated on ITO substrate using conventional electrochemical reduction of 1-naphthyl diazonium salts (NAPH-D) via altering its concentration ranging from 2 mM to 12 mM with a step size of 2. Surface coverage was significantly tuned by varying NAPH-D concentration, keeping other parameters such as the number of scans and scan rate constant. For lower concentrations (2 mM), the molecular thickness ∼6 nm was obtained, whereas higher concentrations (12 mM) produced around 15–18 nm thickness. Atomic force microscopy (AFM), cyclic voltammetry, and electrochemical impedance spectroscopy (EIS) in the presence of a ferroc...
ACS applied materials & interfaces, 2015
Mesoporous ATO nanocrystalline electrodes of micrometer thicknesses have been prepared from ATO nanocrystals and the grafted copolymer templating agents poly-vinyl chloride-g-poly-(oxyethylene methacrylate). As-obtained electrodes were characterized by high interfacial surface areas, large pore volumes, and rapid intra-oxide electron transfer. The resulting high surface area materials are useful substrates for electrochemically catalyzed water oxidation. With thin added shells of TiO2 deposited by atomic layer deposition (ALD) and a surface-bound Ru(II) polypyridyl chromophore, they become photoanodes for hydrogen generation with an added reductive scavenger.