Production of a stable and homogeneous colloid dispersion of nano CoAl2O4 pigment for ceramic ink-jet ink (original) (raw)
Related papers
Preparation of CoAl2O4 nanoblue pigment via polyacrylamide gel method
Powder Technology, 2014
The purpose of this study is to define the preparation of CoAl 2 O 4 as a nano-ceramic blue pigment via the polyacrylamide gel method. The powders were studied by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), thermo-gravimetric (TG) and differential thermal analysis (DTA), Fourier transform infrared spectroscopy (FTIR) and UV-visible techniques (UV-vis). Crystallized CoAl 2 O 4 was obtained after calcination at 600°C. The obtained powders in low temperature had a platy structure. By increasing the temperature, the layered structure was crushed into smaller pieces. The average particle size was approximately 18 nm. The UV-vis spectra presented three bands at 551, 590 and 628 nm attributed to the Co 2+ spin transitions in tetrahedral sites. The results showed that a different calcination temperature causes a variation in the color and size of the particles. The temperature for obtaining blue CoAl 2 O 4 was about 1000°C.
Industrial Ink-Jet Application of Nano-Sized Ceramic Inks
Advances in Science and Technology, 2006
Ink-jet printing is becoming a leading technology for traditional ceramics, due to its capacity of reproducing highly resolved and customized images on tile surfaces. Nano-sized inks, produced by the polyol synthesis route, proved to fulfil the printing requirements, tailoring their chemico-physical properties (e.g. viscosity, surface tension) on industrial ink-jet devices, so representing a major breakthrough in the quadrichromy process.
Nano-Sized Ceramic Inks for Drop-on-Demand Ink-Jet Printing in Quadrichromy
Journal of Nanoscience and Nanotechnology, 2008
Nano-sized ceramic inks suitable for ink-jet printing have been developed for the four-colours CMYK (cyan, magenta, yellow, black) process. Nano-inks of different pigment composition (Co1–xO, Au0, Ti1–x–ySbxCryO2, CoFe2O4) have been prepared with various solid loadings and their chemico-physical properties (particle size, viscosity, surface tension, ζ-potential) were tailored for the ink-jet application. The pigment particle size is in the 20–80 nm range. All these nano-suspensions are stable for long time (i.e., several months) due to either electrostatic (high ζ-potential values) or steric stabilization mechanisms. Both nanometric size and high stability avoid problems of nozzle clogging from particles agglomeration and settling. Nano-inks have a Newtonian behaviour with relatively low viscosities at room temperature. More concentrated inks fulfil the viscosity requirement of ink-jet applications (i.e., <35 mPa˙s) for printing temperatures in between 30 and 70 °C. Surface tensi...
CoAl2O4 Nano Pigment Obtained by Combustion Synthesis
… Journal of Applied …, 2011
The aim of this research was to study the influence of pH (2.5, 7, 10.5), molar ratio of fuel to nitrates (0.36, 0.56, 0.75), and calcination temperature (600, 800, 1000, 1200°C) on the characteristics of CoAl 2 O 4 nano pigments synthesized using a solution-based combustion method. Gel formation, morphology, specific surface area, and color of the powder were characterized using TG-DTA (thermogravimetric and differential thermal analysis), XRD (X-ray diffraction), TEM (transmission electron microscopy), BET (Brunauer-Emmett-Teller), and UV-Vis. The results indicate that spinel CoAl 2 O 4 was formed independently of the different variables studied and that higher temperature promotes crystallite size. According to the TEM micrographs, most of particles calcined at 800 and 1000°C have average particle sizes <30 and 75 nm, respectively. Consistent with BET results, maximum specific surface area was obtained at pH of 7. Colorability tests demonstrate that the mixtures of glaze and calcined nano pigments are still dark blue after heating up to 1200°C. *ali.allahverdi@iust.ac.ir
Colour performance of ceramic nano-pigments
Dyes and Pigments, 2009
Ceramic nano-pigments have been recently developed for ink-jet decoration of ceramic tiles using quadrichromic technology (cyan, magenta, yellow, and black colours). The colouring mechanisms and performance of CoAl2O4, Au, (Ti,Cr,Sb)O2 and CoFe2O4 nano-pigments were investigated by DRS, XRD and colorimetry. The nano-pigments were dispersed in several ceramic glazes and glassy coatings and their colour performance was compared with that of conventional micro-pigments. Each nano-pigment was characterized in terms of its colour mechanism and chemico-physical stability. Although the micro-pigments provided more saturated hues, intense colours were achievable in nano-pigments despite their very small particle size (<50 nm). Limitations to the use of nano-pigments arose for very high firing temperatures (>1200 °C) due to particle growth (e.g. Au) or dissolution in the glassy phase (e.g. titania).
American Scientific Research Journal for Engineering, Technology, and Sciences, 2020
By acknowledging the importance of Nano tech inkjet inks, the “top down” method of nanotechnology was followed for manufacturing the Nano tech inkjet inks of pigment Yellow 14 powder 100 % dried and pigment Blue 15.1 (100 % dried powder) and then characterized for their particle size, zeta potential, purity, viscosity, surface tension, foam, pH, engineering stability, shear thinning, by using different spectroscopic, microscopic and particle size analyzing techniques. Both of the inks were applied on 100 % singed, desized, scoured, bleached and pretreated cotton weight 134.4g/m2 through Monna Lisa Evo TRE printer EPSON (Model No EVO TRE 16). The printed samples were dried and cured 150 °C for 5 minutes. The samples were evaluated for their color fastness to light, rubbing, washing, laundering, and K/S value, by using relevant AATCC and ISO’s methods. Same powders were emulsified and applied on same cotton through traditional rotary screen printing method, dried, cured at 150 °C for ...
Influence of nano‐coated pigment ink formulation on ink‐jet printability and printing accuracy
Coloration Technology, 2017
Pigment ink was formulated with nano‐coated pigment dispersion, prepared via mini‐emulsion polymerization. To study the effect of nano‐coated pigment, surfactant and humectant on ink‐jet printability, the trajectory of droplets with different pigment ink composition was monitored. The effect of ink formulation on the accuracy of printing process of the pigment ink was discussed by study on line width and edge contour of printed patterns. Experimental results indicated that the additives and properties of the pigment ink had a great influence on droplet formation and precise positioning of the printed patterns. The optimal composition for the pigment ink as following: nano‐coated pigment dispersion was 20% w/w, surfactant (S‐465) was 1.5% w/w, humectant (diethylene glycol) was 30% w/w and defoamer (FB‐50) was 0.1% w/w. The prepared pigment ink exhibited excellent freeze–thaw, thermal and centrifugal stability. In addition, the optimal formula was beneficial to form a stable droplet a...
Ceramic pigments for digital decoration inks: an overview
The field of ceramic colorants is one of the most conservative in tile making. Reduction of cost and impact on health and the environment have been the driving force for innovation in pigment manufacturing, where the main technological goals were fast synthesis routes and minimizing hazardous components and additives. The advent of digital decoration is overviewed with its paradigm shift from colorant to ink. The requirements for ink-jet printing are reviewed: rheological properties, surface tension, zeta potential, sedimentation, drop size and shape, kinetics of penetration, particle size, control of electrical and magnetic properties, stability in organic media, improved colorant strength. As conventional pigments and dyes proved to be unsuitable for digital decoration, colorant manufacturers were forced to upgrade processing (micronizing step for pigments) and to become involved in ink design (improving colorant strength for dyes). By this way, different classes of colorants for digital ink have been developed: organo-metallic complexes, micronized pigments, colloidal metals, nanopigments and reactive sol precursors for in-situ synthesis. The main challenges for ink manufacturers are still the stability over time (sometimes limited to a few weeks) and the gamut (much narrower than that of conventional ceramic colorants). As a matter of fact, typical quadrichromy or hexachromy is still a hard task to be achieved with ceramic colorants and tile makers are often choosing unconventional colour sets based on brown shades. This circumstance is revitalizing the industrial interest towards alternative routes for pigment synthesis (chimie douce or bottom-up approach) and technological solutions to improve the colour performance (pigment coating, core-shell structures, use of primers and buffers). Physico-chemical properties of inks, which affect the stability over time, are turning critical with increasing diffusion of digital decoration. From this standpoint, technologies able to control colloidal suspensions and to design hybrid organic-inorganic composites are rapidly gaining interest and application potential.
Efficient and Environmentally Friendly Ink-Jet Printing of Ceramic Thin Films
Nanoscience and Nanotechnology Letters, 2013
The use of titania photocatalytic materials in industrial applications is strongly dependent on the stability, nanoparticle size distribution, ease of deposition and cost of the relevant titania precursor solutions or suspensions. The present contribution presents the preparation of inkjet-printed titania films, derived from stable water-based suspensions. The suspensions were synthesized by applying a "top-down" synthetic strategy, namely the ultrasonication of commercially available titania powder (Evonik Aeroxide P25). Crucial parameters, such as suspension stability, energy input requirements, particle size distribution, surface characteristics, compatibility with industrially proven inkjet systems and photocatalytic performance were investigated. The developed synthetic procedure proves environmentally friendly, low cost and most suitable for large scale production of titania thin films, by inkjet printing commercially available ceramic tiles.
Effect of Ink Formulation and Paper Surface Morphology on Ink-jet Printing Properties
Progress in Color, Colorants and Coatings, 2014
he purpose of this study was to investigate the effect of different type of alcohols and humectants in inks formulation, as well as the influence of paper surface morphology on the ink-jet printing properties. In order to investigate the influence of alcohol and humectant types on printing properties, the optimum ink containing C.I. Reactive Blue 21 (Ink2) was formulated with different type of alcohols and humectants. The results of optical density and water fastness evaluations indicated that, the prints depend more on paper surface morphology rather than the type of alcohols and humectants in ink formulation. Optimum optical density and good water fastness properties were obtained on glossy coated ink-jet printed papers comprising optimum-diameter nano-porosities in their coating layer. Prog.