Shear bond strength of one-step self-etch adhesives to enamel: effect of acid pretreatment (original) (raw)
Related papers
American journal of dentistry, 2012
To assess the influence of preliminary phosphoric acid-etching on shear bond strength (SBS) to enamel and dentin of a self-adhering restorative composite and of a new self-etch adhesive used in combination with the proprietary flowable composite. 100 human molars were selected. SBS was assessed on flat buccal enamel surfaces and mid-coronal dentin. Teeth from each group were divided into five subgroups (n=10): (1) FL: etch-and-rinse adhesive OptiBond FL/Premise flowable; (2) XTR: 2-step self-etch adhesive OptiBond XTR/Premise flowable; (3) eXTR: OptiBond XTR on etched substrates/Premise flowable; (4) VF: self-adhering flowable composite Vertise Flow; (5) eVF: Vertise Flow on etched substrates. Specimens were stressed in shear until failure. Failure modes were evaluated under a stereomicroscope. Data were analyzed by two-way ANOVA and Fisher's exact test (P< 0.05). Dental substrate, material and between-factor interaction significantly influenced SBS (MPa). In FL group (16.83 ...
The journal of adhesive dentistry, 2012
Purpose: To compare shear bond strengths of three different self-etching adhesive systems of different pH values to enamel bleached with carbamide peroxide, treated with casein phosphopeptide-amorphous calcium phosphate (CPP-ACP), or treated with CPP-ACP subsequent to bleaching with carbamide peroxide. Materials and Methods: Thirty-six human third molars were cut into 4 sections and randomly assigned to 4 groups (n = 36): group I: no treatment; group II: bleaching; group III: CPP-ACP; group IV: bleaching and CPP-ACP. After surface treatments, the samples of each group were further divided into three subgroups (n = 12) based on the adhesive used. The adhesives Clearfil SE Bond (CSE), AdhesE (ADE), and Adper SE Plus (ADP) were applied, and resin composite cylinders with a diameter of 2 mm and a height of 4 mm were bonded to the enamel. Then the specimens were subjected to shear bond strength testing. Two-way ANOVA and a post-hoc Tukey's test were used for statistical analysis (α ...
European Journal of Dentistry, 2012
ABSTRACTObjectives: The aim of this study was to compare the shear bond strength of several self-etch adhesives to their two-step predecessors to ground and unground enamel.Methods: Seventy-five extracted, non-carious human third molar teeth were selected for this study. The buccal surfaces of each tooth were mechanically ground to obtain flat enamel surfaces (ground enamel), while the lingual surfaces were left intact (unground enamel). The teeth were randomly divided into five groups according to the adhesive systems (n=15): one-step self-etch adhesive - Clearfil S3 Bond, its two-step predecessor - Clearfil SE Bond, one-step self-etch adhesive - AdheSE One, and its two-step predecessor - AdheSE, and a two-step etch-and-rinse adhesive - Adper Single Bond 2(control). After application of the adhesives to the buccal and lingual enamel surfaces of each tooth, a cylindrical capsule filled with a hybrid composite resin (TPH) was seated against the surfaces. The specimens were stored in ...
Journal of applied biomaterials & functional materials, 2015
The purpose of this in vitro study was to evaluate the dentin shear bond strength of 4 self-etching adhesives having a different pH on primary and permanent teeth dentin. The occlusal enamel was removed from 60 freshly extracted third molar and 60 primary second molar human teeth, which were randomly separated into 4 groups (n = 15). Four adhesive systems were applied: G-Bond (GC Corporation, Tokyo, Japan, pH: 1.5), Futura Bond M (Voco, Cuxhaver, Germany, pH: 1.4), Adper Prompt L-Pop (3M/ESPE, St Paul, MN, USA, pH: 0.8), and Clearfil S3 Bond (Kuraray Medical, Tokyo, Japan, pH: 2.7) according to the manufacturer's instructions. After the application of dentin bonding agents, a composite resin material (Z250 Restorative A2, 3M ESPE, St. Paul, MN, USA) for permanent teeth and a compomer resin material (Dyract Extra A2, Dentsply, Konstanz, Germany) for primary teeth was applied onto the prepared dentin surfaces. The data were obtained by using a universal test machine at a crosshead...
Brazilian Journal of Oral Sciences, 2007
The aim of this study was to evaluate the bond strength of adhesive systems to intact and ground enamel. Enamel blocks from buccal and lingual surfaces of third molars were used for bonding procedures. Intact or ground (600-grit SiC paper) enamel surfaces were bonded using two "etch&rinse" adhesives (Prime&Bond 2.1 and Single Bond), three self-etching primer systems (Optibond Solo Plus SE; Tyrian SPE/One-Step Plus and UniFil Bond) or two self-etching adhesives (One-Up Bond F and Xeno III). A 6-mm composite crown was built on the bonded surfaces and samples were stored for 24 hs at 37°C. Samples were sectioned into 0.9-mm-thick slabs, each slab trimmed to a cross-sectional area of 0.8 mm2 and specimens loaded to failure at a crosshead speed of 0.5 mm/min, using a universal testing machine. Microtensile bond strength data (n=6) were analyzed using Kruskal- Wallis and Dunn tests. Differences in bond strength between intact and ground surfaces were not significant for both &qu...