Evaluation of compatibility of EPDM and butyl rubber—II. Thermal and radiation stability (original) (raw)
Related papers
COMPATIBILIZATION OF RUBBER BLENDS BY γ-IRRADIATION PROCESSING
normal pressure. The contribution of . In such units the cables and seals may be exposed to low rate irradiation at room temperature. Their durability is estimated at about 30 years [1]. Particular service illustrated by accidental events requires suitable behaviour under hard operation conditions. Long time duty is based on certain properties that guaranty the high performances of units. In spite of low risk of nuclear equipment for power transmission and instrumentation, evaluation of chemical stability of polymers must gain appropriate attention. Various polymer materials like monocomponent systems or blends have been checked by means of accelerated tests in order to found satisfactory formulas for products [for example, 2-5].
Radiation processing of ethylene-propylene rubber
Journal of Applied Polymer Science, 2000
The effects of ionizing radiation on ethylene-propylene copolymer were evaluated over the range of total ␥ doses up to 500 kGy. The influence of the irradiation dose was investigated by oxygen uptake and thermal analysis. Four testing temperatures (170, 180, 190, and 200°C) and two heating rates between 2.9 and 5.9 K/min were selected for oxygen uptake measurements and thermal analysis, respectively. The competition between crosslinking and scission was examined on the basis of kinetic parameters of postirradiation oxidation. The influence of the momentary concentration of hydrocarbon free radicals is discussed in regard to the contribution of the antagonistic processes of crosslinking and oxidative degradation.
Effect of gamma irradiation on ethylene propylene diene terpolymer rubber composites
Nuclear Instruments & Methods in Physics Research Section B-beam Interactions With Materials and Atoms, 2008
Composites of ethylene propylene dine terpolymer rubber (EPDM), high density polyethylene (HDPE) and ground tire rubber powder (GTR) at different ratios were subjected to gamma irradiation at various doses up to 250 kGy. The physical, mechanical and thermal properties were investigated as a function of irradiation dose and blend composition. Gamma irradiation led to a significant improvement in the properties for all blend compositions. The results indicate that the improvement in properties is inversely proportional to the substituted ratio of GTR, attributed to the development of an interfacial adhesion between GTR and blend components. The results were confirmed by examining the fracture surfaces by scanning electron microscopy.
Journal of Applied Polymer Science, 2007
Blends of waste low-density polyethylene with waste butyl rubber of equal quantities containing reactive compatibilizing agents, namely: maliec anhydride; glycidyle methacrylate, divinyl benzene, tetraethyleneglycoldimethacrylate and diethyleneglycoldimethacrylate were prepared and exposed to different c-irradiation doses up to 400 kGy. The swelling behavior in organic solvent of the gel and soluble fractions and the degree of crosslinking were investigated. The mechanical properties, namely tensile strength and elongation at break were also studied. Thermal properties using thermo gravimetric analysis and differential scanning calorimetry analysis follow analyses have been followed up to follow the change of the structure for the irradiated and nonradiated blends. Results obtained indicated improvement in physical, mechanical and thermal properties on irradiation of the prepared blends which incorporate compatibilizing agents, but with varying degrees.
Arabian Journal of Chemistry, 2016
Gamma irradiation radical-radical interaction crosslinking of elastomers and thermoplastic is a special type of crosslinking technique that has gained importance over conventional chemical crosslinking method as process is fast, pollution free, and simple. In this work a blend polymer, based on waste polyethylene and nitrile butadiene rubber, has been irradiated with gamma-rays, mechanically and thermally investigated at varying NBR content. FTIR and SEM techniques were used in addition to the swelling behavior to emphasize the blend formation. Mechanical properties like tensile strength, elongation at break and modulus at different elongations were studied and compared with those of unirradiated ones. A relatively low-radiation dose was found effective in improving the level of mechanical properties. Differential scanning calorimeter and thermogravimetric analysis were used to study the thermal characteristics of the irradiated polymer. Enhancement in thermal stability has been observed for higher NBR containing blends and via radiation-induced crosslinking up to %50 kGy.
Gamma-Radiation Effect on Mechanical Properties of Pp / Epdm Polymeric Blends
2016
Thermoplastic elastomers (TPEs) are provided with many properties of elastomeric or rubbery materials, but can be processed with the thermoplastic processing methods; they are one of the fastest growing polymers materials which combine the elastic and mechanical properties of crosslinked rubbers with the melt processability of thermoplastics. In addition, TPEs find a lot of applications in automotive, buildings and construction, wires and cables, etc.; besides their ability to reuse and recycle the production scrap and waste. Polypropylene (Pp) is a commodity, with high melting point, high chemical resistance, low density, with a balance between physical and mechanical properties and easy processing at low cost. Nevertheless, Pp shows limitations for some special applications, in terms of impact resistance; in order to minimize this characteristic, an impact modifier, as Ethylene Propylene Diene Terpolymer (Epdm) can be used. Due to different polarity and structure between the therm...
Radiation-induced degradation of butyl rubber vulcanized by three different crosslinking systems
Radiation Physics and Chemistry, 2012
Butyl rubber (IIR) is an isobutylene/isoprene copolymer and is provided with good properties including low permeability to gases, good thermal stability and high resistance to oxygen and ozone action, among others. It is well known that the major effect of ionizing radiations on butyl rubber is chain scission accompanied with a significant reduction in molar mass. This work aimed to study the effects of gamma radiation on the properties of butyl rubbers vulcanized by three different curing systems, such as, the ones based on sulfur, sulfur donor and phenolic resin to identify which curing system is the most stable under irradiation. The butyl rubber vulcanized by three different systems was gamma irradiated with doses of 25 kGy, 50 kGy, 100 kGy, 150 kGy and 200 kGy. Irradiated and non-irradiated samples were characterized by the following techniques: tensile, elongation and hardness. It was observed that doses higher than 150 kGy practically destroy the assessed properties for all butyl compounds, irrespective of the vulcanization system used; however compounds cured with phenolic resin showed a decrease in properties proportional to the dose.
Radiation Physics and Chemistry, 2019
The influence of polyfunctional monomers (PFMs) and radiation dose on the physicomechanical properties of acrylic rubber /styrene butadiene rubber (ACM/SBR) blend (50/50) was investigated. A series of ACM/SBR blends were prepared by varying the ratio of PFMs, namely ethylene glycol dimethacrylate (EGDMA) and pentaerythritol triacrylate (PETA). The different blends were crosslinked by gamma radiation doses up to 100 kGy. It was observed that the gel content, mechanical properties and thermal stability improved as the radiation dose increased. Improved physico-mechanical properties were obtained at lower radiation dose by incorporation of PFMs as co-agent. The results showed that the blends containing EGDMA gave the best results.