Simulation of a waste incineration process with flue-gas cleaning and heat recovery sections using Aspen Plus (original) (raw)
Related papers
Modelling of a Dual Purpose Plant for Waste Incineration
In the present paper, the modelling of a dual-purpose plant for the production of electrical and thermal energy from the heat treatment of wastes is presented. Particularly, the model has been developed with the aim of performing a study about the simulation of a solid waste incineration process, which involves complex gas-solid reactions, in a fluidized bed combustor. The incineration plant is made of three sections, and namely a RDF combustion section, a flue gas treatment section and a thermal recovery section. This paper is mainly focused on the combustion section. Model results have been compared with the experimental data obtained derived from literature, showing a very good agreement. The proposed model may represent a useful and a reliable instrument to be used in both design and planning of new plants and in control and retrofit of existing plants.
Basic Science Modelling and Simulation of Low Calorific Value Municipal Solid Waste Incineration
2012
ENGLISH/ ABSTRACT (ENGLISH/ ABSTRACT (ENGLISH/ ABSTRACT (ENGLISH/ ANGLAIS The paper focused on the mathematical modellin g and simulation of low calorific value municipal solid waste incineration in semiarid region. Municipal solid wastes were collected and analysed; from which wood samples were taken and incinerated using a prototype incinerator. A mathematical model, based on Fourier series (FS) and finite elements method (FEM) was developed, ran and validated using experimental and literature data. Critical minimum volume of 4.93 m 3 or about 6 % of the total volume of the incinerator would be needed at 20% moisture content refuse and a critical maximum volume of 51.10 m 3 or 69.21% of the total volume, would be needed at 50% moisture content. The ignition time and the time at which the combustion becomes self-sustaining are greatly influenced by the moisture content. Critical drying temperature was found to be 711.44 K. The grid size had little or no effect on the simulated resu...
Mathematical Modeling of a Solid Waste Incineration System and Steam Generation
17th Brazilian Congress of Thermal Sciences and Engineering, 2018
Population growth, technological progress and changes in consumption patterns in recent years have led to an increase in the solid waste. On the other hand, limit energy resources and raw materials caused waste to be considered as a waste material and also recyclable at the high level of scientific and applied research. In solid waste management, waste burning is regarded as one of ways for eliminating waste. In this study, municipal waste in one of the districts of Tehran was taken into account for a case study. Also, in special systems which need special care of temperature such as the system for controlling the temperature of the furnace fuel of burnable solid waste in temperature 950°C. Fuel requirements for design were also calculated. At the end of the project, fluent software was used to confirm the findings obtained from the city incinerator furnace design.
MODELING AND SIMULATION OF A SOLID WASTE INCINERATION SUSTAINABLE ENERGY SYSTEM
Urban solid waste generation has drastically grown around the world, requiring creative, ecologically correct and sustainable solutions to be developed. This work considers a problem of thermodynamic optimization of extracting the most energy from a stream of hot exhaust produced by urban solid waste incineration, considering a stoichiometric combustion model, when the contact heat transfer area is fixed. For that, a mathematical model is introduced to evaluate the rate of heat generation due to the waste incineration process, and the exergetic (power) rate captured by a heat recovery steam generator (heat exchanger). The numerical results show that when the (cold) receiving stream boils in the counterflow heat exchanger; the thermodynamic optimization consists of locating the optimal capacity rate of the cold current. At the optimum, the cold side of the heat transfer surface is divided into three sections: preheating of liquid, boiling and superheating of steam. Experimental results are in good qualitative and quantitative agreement with the numerically calculated mathematical model results. Microalgae cultivated in large-scale vertical tubular compact photobiorreactors are investigated to treat the emissions produced by the incineration, and to increase the efficiency of the global system via cogeneration of co-products with high aggregated commercial value. NOMENCLATURE A area, m 2 í µí± í µí±í µí± specific heat of steam at constant pressure, J/kg K í µí± í µí± specific heat at constant pressure, J/kg K ℎ í µí± , ℎ í µí± Enthalpy of input and output J/kg í µí±̇ mass flow rate, kg/s í µí± mass M ration of mass flow rates
CFD modelling of a RDF incineration plant
Applied Thermal Engineering, 2016
The operation of waste-to-energy plants based on incineration inevitably implies the production of greenhouse gases and the emission of harmful species to the human health. The European Directive on the construction and operation of incineration plants fixes strict rules concerning the temperature and the residence time of the combustion products within the combustion chamber. Indeed, acting directly on the combustion process to limit the emission of pollutants at the source is a well assessed alternative to post combustion technologies. The peculiar characteristics of the treated waste or Refuse Derived Fuel (RDF) may also cause problems to the long term operation of the burner, as in the case of deposits formation due to the presence of ash. The ash particles, entrained in the in-chamber flow, may stick on the walls even at relatively low temperatures, thus modifying the heat transfer coefficient, reducing the system efficiency and imposing frequent stops for overhauling. Therefore, the characterization of the phenomena occurring in a RDF combustor through experimental and/or numerical techniques is strongly demanded for assisting its optimal maintenance. This work presents the assessment and validation of a Computational Fluid Dynamics (CFD) model of a real scale waste-to-energy plant operating in central Italy, which couples the thermo-chemical conversion of the solid RDF to the gaseous combustion of the released syngas. The model allows to characterise into detail the temperature and residence time of the combustion products, for the verification of the fulfilment of the existing regulation for dioxin formation in incineration plants.
Architecture, Civil Engineering, Environment
Poland was collected 9.6 million tonnes of municipal waste in 2012 (plus update). The primary method of dealing with municipal waste collected was organized depositing them in landfills. Mixed municipal waste accounted for almost 90% of all municipal waste collected (8.6 million tonnes). Poland is one of the lowest in the EU in terms of the use energy from waste. The analysis of complex real-time physical processes, thermal waste processing and determination of their optimal parameters requires a series of studies and detailed analysis of constituents of elementary processes (degassing, gasification, combustion). The apparent simplicity of process implementation often determines knowledge and practical experience required in their application. The relationships known and used in the design usually concern a homogeneous substance (conventional fuels) and do not correspond to the conditions and needs of processing of complex substances of a different chemical composition and physic-chemical properties. Due to the complexity of the real process, numerical calculations were carried out to simulate the operation of a waste incineration technology. For this purpose a mathematical model was developed as well as its implementation in the programming code of a high-level language. In order to calibrate and validate the model (compliance with the real process) calculations were performed on a specially prepared set of validation data. The authors analysed a group of processes that belong to one technology, looking into connections between degassing, gasification and combustion of carbonized substances in pure oxygen.
Numerical Simulation of Refuse-Derived Fuel ThermoChemical Conversion in a Waste-to-Energy Plant
Waste Energy and Management
since 1984 he worked at SSRC, HIAST, CNR, CRF, DCU and UWS. Prof Olabi has supervised postgraduate research students (10 M.Eng and 30PhD) to successful completion. Prof Olabi has edited 12 proceedings, and has published more than 135 papers in peer-reviewed international journals and about 135 papers in international conferences, in addition to 30 book chapters. In the last 12 months Prof Olabi has patented 2 innovative projects. Prof Olabi is the founder of the International Conference on Sustainable Energy