Gravure Printability of Conducting Polymer Inks (original) (raw)
Related papers
Investigation of Roll-to-Roll Gravure Printing for Printed Electronics with Fine Features
2020
Gravure printing is known to be cost competitive in manufacturing of printed electronic devices due to its capability to mass produce at lower costs. Current standard of gravure printed feature sizes is in a range of around 50 μm down to sub-10 μm, predominantly through small scale setups and specialized engraving. However, reliance on gravure cell design limits the scalability of printing over a large area due to the setup cost. In this study, ink viscoelastic behavior was modified to improve replication of gravure printed features over a large printing area of 300 mm web-width without a reduction in gravure cell dimension. Fine lines were printed using a high viscosity ink with a good replication of the nominal line width. Control over the printed features was performed through the variation of printing speed and the alteration of ink viscosity. The effects of ink viscosity and printing speed on the printed ink particle distribution and size were also examined. New methodologies o...
Cellulose Chemistry and Technology
In the present work, various surface treatments of base paper were investigated in order to make it suitable for application in printed electronics. A functional coating based on silica pigment was preceded by PVOH-containing precoating, and differently surface treated papers were characterized in terms of surface roughness, relative area of surface pores, wettability, printability and by FTIR spectroscopy. The precoating had a significant effect on the constriction of through-pores, the reduction of their number, and on the permeability of the functional coating, and it increased the dynamic contact angle of the liquids. Analysis of FTIR spectra of precoated and functionally coated paper confirmed a higher content of polyvinyl alcohol binder and cationic polymer in the functional coating, compared to that of functionally coated paper, without precoating. SEM analysis showed that the silver layer of the RFID antenna printed by inkjet on the precoated and functionally coated paper was continuous. Better printability of the precoated and functionally coated paper, compared to the functionally coated paper, without precoating, was also confirmed by higher electrical conductivity of the dipole of the RFID antenna, which reached the level of the antenna printed on a commercial inkjet PET film.
Studies on inkjet-printed conducting lines for electronic devices
Journal of electronic materials, 2007
Inkjet printing is considered one of the most promising methods for patterning and materials deposition. The feasibility of employing inkjet technology for the creation of conductive pathways on printed circuit boards is addressed herein. Prediction of the width, length, and thickness of printed lines as a function of the dot diameter, resolution, and volume fraction of the particles in the ink is presented. Surface treatment of the substrate to promote desirable adhesion and wetting properties as well as the adjustment of the curing process to reduce the surface roughness of the printed traces were studied. In a sintering study, samples sintered at 250°C for 20 min showed a resistivity of 4.2 lX cm, which is approximately 2.6 times that of bulk silver. A low-temperature sintering method through the reduction of a metal salt is presented. The resistivity of printed samples sintered at 140°C for 30 min in the presence of silver nitrate with N,N-dimethylformamide showed a resistivity of 22.5 lX cm.
Coated Surfaces for Inkjet-Printed Conductors
In this thesis, a number of commercially available paper substrates of various types are characterized and their characteristics related to the performance of inkjetprinted conductors using silver nanoparticle ink. The evaluated performance variables are electrical conductivity as well as the minimum achievable conductor width and the edge raggedness. It is shown that quick absorption of the ink carrier is beneficial for achieving well defined conductor geometry and high conductivity. Surface roughness with topography variations of sufficiently large amplitude and frequency is detrimental to print definition and conductivity. Porosity is another important factor, where the characteristic pore size is much more important than the total pore volume. A nearly ideal porous coating has large total pore volume but small characteristic pore size, preferably smaller than individual nanoparticles in the ink. Apparent surface energy is important for non-absorbing substrates but of limited importance for coatings with a high absorption rate. Additionally, a concept for improving the geometric definition of inkjet-printed conductors on nonporous films has been demonstrated. By coating the films with polymer-based coatings to provide a means of ink solvent removal, minimum conductor width were reduced a factor 2 or more. Intimately connected to the end performance of printed conductors is a well adapted sintering methodology. A comparative evaluation of a number of selective sintering methods has been performed on paper substrates with different heat tolerance. Pulsed high-power white light was found to be a good compromise between conductivity performance, reliability and production adaptability. The purpose of the work conducted in this thesis is to increase the knowledge base in how surface characteristics of papers and flexible films affect performance of printed nanoparticle structures. This would improve selection, adaption of, or manufacturing of such substrates to suit printed high conductivity patterns such as printed antennas for packaging.
Polymeric materials for printed electronics and their interactions with paper substrates
Proc IS&T Digital …, 2007
The primary goal of printing electronics is to create structures and devices that are functionally similar to conventional electronics, but at greater speed, lower cost and less production complexity. The applications that will be affected by lower cost of electronics include RFID tags, solar cells, displays, chemical sensors, etc. In this work, effects of paper properties and their effect on sheet resistivity of gravure printed PEDOT:PSS layers were evaluated. Among paper properties, it was observed that absorptivity and ink penetration had negative effect on conductivity. The higher the ink penetration into the substrate surface the lower the conductivity. Moreover, surface energy of the substrates needs to be in balance with surface tension of the conductive inks.
Printable Electronics: Patterning of Conductive Materials for Novel Applications
MRS Proceedings, 2004
ABSTRACTThe convergence of materials science, printing, and electronics promises to offer low cost and high volume production of devices such as transistors, RFID tags, wearable electronics and other novel applications. Although a number of “soft lithographic” techniques have been used to make these devices, they are slow and have a limited production volume [5], [14-15].Here high volume printing processes like rotary letterpress, flexography and offset lithography have been investigated for patterning conductive materials [1]. The synthesis and development of conducting inks using electrically functional polymers has been studied. The feasibility of using such inks in high volume printing processes has been studied. An attempt has been made to print conductive interdigitated electrodes using these inks to obtain uniform coating properties and appropriate electrical characteristics. Various process parameters like type of substrate, inking time and speed, printing pressure, printing...
Paper Substrates and Inks for Printed Electronics
2000
The present work explores the effects of paper properties on conventional silver-based conducting inks. The effects of smoothness, relative humidity, porosity, permeability and wettability on electrical properties of silver inks on different paper substrates were studied. Another objective of this work was to prepare and study polyaniline synthesized in the presence of different lignosulfonates.
Gravure Printability From Laser and Electromechanically Engraved Cylinder
Gravure printability comparison of laser engraved and electromechanically engraved cylinders was done on five different substrates. Ink transfer was less reduced on laser print than electromechnaical when printed without electrostatic assist. Print mottle was significantly lower and yellow, magenta and black laser engraved images, while cyan print from laser engraved cylinder had higher mottle on some substrates (SCB, SCA and freesheet). Overall, the print quality than that from the electromechanically engraved one.