Design, Simulation and Modeling of a Micromachined High Temperature Microhotplate for Application in Trace Gas Detection (original) (raw)
Related papers
Thermal model for a microhot plate used in a MEM gas sensor
2008
A thermal analytical model for a MEM gas sensor is presented and compared with an electrical circuit equivalent model. The objective is to study the temperature performance of the microhot plate configured within a MEM structure used for gas sensing. From this, it is possible to determine the magnitude of the electrical current that must be applied to the polysilicon heater on regard of its dimensions and materials used, for instance, when the sensor structure is fabricated with a MEMS technology compatible with CMOS integrated circuits fabrication. Results are presented where the response time and temperature level, as a function of applied current, can be determined. The model presented can be used as a base for designing microhot plates operating in gas sensors, where temperatures in the order of 300 • C are needed and that will be integrated monolithically with associated electronics, with constraints as minimum power dissipation.
Thermal simulation and optimization of micromachined gas sensor structure
2010
This work is concerned on analysing of the thermal parameters of suspended micromachined structure based on GaAs for gas detection. The main attention was dedicated to minimazin of sensor power consumption. Electro-thermal simulation confirmed the achievement of required operating temperatures (200-320°C) with the heating power less than 25 mW. Avarage temperature gradient in the active area did not exceed 0.6 K/µm.
Electro-thermal simulations and modelling of micromachined gas sensor
2001 Microelectromechanical Systems Conference (Cat. No. 01EX521)
Reliability of the membrane structure for micromachined-gas sensors is one of the main concerns in MEMS technology. The major source of this problem is the stress on the membrane. In this study, the use of SiO 2 /Si 3 N 4 /SiO 2 stacked layers with optimized dimensions was found to reduce the stress on the membrane, hence improve the reliability. We have also used electro-thermal simulations with finite element analysis (FEA) to model the structural properties of the membrane in order to reduce the stress. The appropriate selection of materials and dimensions yielded maximum active area temperature of 530°°°°C at the center of the membrane with a polysilicon as a heater element, less than 5V supply voltage, 40mW of power consumption, membrane edge temperature of 177 °°°°C and acceptable mechanical stress of 0.097GPa. Upon realizing the structure with the modeled parameters, micromachined-gas sensors could respond to many industry/environment application demands.
High performances of new microhotplate for gas sensors
2008
The main goal of this work is to improve significantly performances of microhotplate for gas sensors. This article describes technological optimizations (materials and design) used to reach high and stable operating temperature, in reducing intrinsic drift problems (linked to standard polySilicon heater). Our heating platforms present low buckling effect, low consumption and good thermal homogeneity all over the active area.
An industrializable Silicon-based microhotplate for metal oxides gas sensors
2014
This article presents an industrializable silicon-based microhotplate for metal oxide gas sensors. It introduces an interesting approach and describes the technological optimizations used to reach high and stable operating temperature, in reducing intrinsic drift problems (due to commercial polysilicon heater). The microhotplate present low consumption of 70 mW for 600°C, good thermal homogeneity over the active area and a good mechanical stability.
Design, Simulation, and Optimization of a Meander Micro Hotplate for Gas Sensors
Transactions on Electrical and Electronic Materials, 2016
Micro Hotplate (MHP) is the key component in micro-sensors, particularly gas sensors. Indeed, in metal oxide gas sensors MOX, micro-heater is used as a hotplate in order to control the temperature of the sensing layer which should be in the requisite temperature range over the heater area, so as to detect the resistive changes as a function of varying concentration of different gases. Hence, their design is a very important aspect. In this paper, we have presented the design and simulation results of a meander micro heater based on three different materials-platinum, titanium and tungsten. The dielectric membrane size is 1.4 mm × 1.6 mm with a thickness of 1.4 μm. Above the membrane, a meander heating film was deposed with a thickness of 100 nm. In order to optimize the geometry, a comparative study by simulating two different heater thicknesses, then two inter track widths has also been presented. Power consumption and temperature distribution were determined in the micro heater´s structure over a supply voltage of 5,
Sensors and Actuators B: Chemical, 2006
Micromachined gas sensors that work at high temperatures, namely 700 • C or more, are necessary for some specific applications but they present a thermal cross-talk when they are integrated with other micromachined devices. In this paper we describe the fabrication steps and the implementation of a suspended micro-hotplate device for high temperature gas sensing applications, which presents a very low-power consumption. Simulations with the finite element model tool show that its integration with other micromachined devices is appropriate. The sensor device has been tested with BaSnO 3 under oxygen and CO atmospheres.
2009 6th International Conference on Electrical Engineering, Computing Science and Automatic Control (CCE), 2009
A control system to regulate the temperature of the micro hotplate in a MEMS gas sensor is presented. The controlelement, called micro hotplate, is comprised of a micro heater and a temperature sensor, both made with polysilicon, located near each other. This material has a Temperature Coefficient of Resistance (TCR) that is the basis for the design of the temperature controller of the gas sensor system. A high temperature between 250 and 400 °C is needed to produce a chemical reaction between the gas and the sensing film, hence a reliable temperature control for the micro hotplate is desired. Thermal insulation of the circuitry from the heating element, having a monolithic sensor system, and low power consumption, are the main specifications for the system. This is obtained by means of a micro pit realized with MEMS micromachining processes. The analysis of the circuit proposed to fulfill these characteristics is presented, for its future integration with a standard CMOS technology. A trade off is established between the sensor structure parameters and the circuit design.
Low-cost surface micromachined microhotplates for chemiresistive gas sensors
Microsystem Technologies, 2018
Microhotplate (MHP) based gas sensors have gained significant attention recently due to their small size, low power and feasibility for integration of electronics on the same chip. This study presents the detailed work on design, fabrication and complete characterization of microhotplates based on a standard multi user MEMS process (MUMPs). Suspendedmembrane type MHPs were designed using the available layer combinations of MUMPs. FEM simulations were carried out to optimize the heater design by spatially varying the heater current density to achieve uniform temperature distribution over the sensing area. Topography measurements confirmed that the X-Y-Z dimensions of the fabricated MHPs were in accordance with the design. From electro-thermal characterization, the thermal efficiency of the MHPs was evaluated as * 10°C/mW. The suspended membrane showed a homogeneous temperature of * 450°C at 35-40 mW heater power, which was well above the typical operating temperature of chemiresistive gas sensors. The results presented in this paper provide a pathway for realizing cost effective MHPs for gas sensors based on MUMPs.