Neutron diffraction study of the deformation behaviour of deformation processed copper–chromium composites (original) (raw)
Related papers
Elevated temperature tensile properties and failure of a copper-chromium in situ composite
Journal of Materials Science, 2003
A Cu-10 vol% Cr in situ composite was produced by melt processing and deformed by swaging to form rods with a total deformation true strain of 3.15. Scanning electron microscopy showed that the composite microstructure consisted of Cr fibres aligned with their long axes parallel to the rod axis. X-ray diffraction indicated that the Cr fibres had a strong fibre
Elastic and tensile behavior of nanocrystalline copper and palladium
Acta Materialia, 1997
The elastic and tensile behavior of high-density, high-purity nanocrystalline Cu and Pd was determined. Samples with grain sizes of 10-l 10 nm and densities of greater than 98% of theoretical were produced by inert-gas condensation and warm compaction. Small decrements from coarse-grained values observed in the Young's modulus are caused primarily by the slight amount of porosity in the samples. The yield strength of nanocrystalline Cu and Pd was 10-15 times that of the annealed, coarse-grained metal. Total elongations of 14% were observed in samples with grain sizes less than 50 nm, while a sample with a grain size of 110 nm exhibited > 8% elongation, perhaps signifying a change in deformation mechanism with grain size. Hardness measurements followed the predictions of the Hall-Petch relationship for the coarse-grained copper down to x 15 nm, and then plateaued. Hardness values (divided by 3) were 2-3 times greater than the tensile yield strengths. Processing flaws may cause premature tensile failure and lower yield strengths. The size and distribution of processing flaws was determined by small-angle neutron scattering. Tensile strength increased with decreasing porosity, and may be significantly affected by a few large processing flaws. VI 1997 Acta Metallurgica Inc.
In Situ Analysis of Deformation Mechanisms of Cu-Based fcc Materials under Uniaxial Loading
Materials Science Forum, 2008
By associating texture determinations and strains measurements by neutron diffraction, the elastoplastic behaviours of families of crystallites with the same crystallographic orientations were characterized in situ in a brass and a bronze alloys under uniaxial loading. The polycrystalline orientation analysis method proposed here allows an intermediate approach between a "local" (intragranular) and a "global" characterization, within the bulk of massive samples. Forum Vols. 571-572 (2008) pp 89-94 online at http://www.scientific.net © (2008 Trans Tech Publications, Switzerland Online available since
International Journal of Refractory Metals and Hard Materials, 2018
Cu-refractory metal composites containing Cr, Mo or W were subjected to severe plastic deformation using room temperature high-pressure torsion (HPT). A lamellar microstructure developed in each of the composites at equivalent strains of ∼75. The refractory metals developed {hkl} 111 fibre textures with a slight tilt to the tangential direction. This texture was stronger and more clearly defined in Mo and W than in Cr. By applying additional HPT deformation to these samples, perpendicular to the original shear strain, it was found that the lamellar structure of Cu30Mo70 and Cu20W80 (wt.%) composites could be retained at high equivalent strains and the refractory layer thickness could be reduced to 20-50 nm in Cu20W80 and 10-20 nm in Cu30Mo70. Although neighbouring regions of the microstructure were aligned and there was evidence of local texture in both composites, the bulk texture of Cu30Mo70 became weaker during this second step of HPT deformation. This was attributed to the refractory metal lamellae being discontinuous and imperfectly aligned. This work shows that it is possible to form ultrafine composites of Cu-group VI refractory metals via high-pressure torsion, with namolamellar structures being possible where there is a sufficient volume fraction of Mo or W.
Microstructure and properties development of copper during severe plastic deformation
Materials & Design, 2007
Annealed pure copper was subjected to equal-channel angular pressing (ECAP) to produce a nanocrystalline (NC) structure. The microstructure and the development of the mechanical properties of copper under severe plastic deformation (SPD) were studied. The structural changes and the properties due to heat treatment and the different loading methods of NC copper were analyzed and compared. The results show that the heat treatment and the hard cyclic deformation in the viscoplastic regime influence the properties of NC copper to a great extent. The ultimate tensile strength and the microhardness of NC copper decrease while heat-treated NC copper acquires enhanced true tensile properties after hard cyclic deformation in the viscoplastic regime.
“Development of Cu based metal matrix composites by mechanical alloying route”
Chapter 1 Introduction 1 1.1Motivation and Background of the Present Investigation Chapter 3 Experimental Details 3.1 Equipment used in the Present Investigation 3.2 Selection, Synthesis and Characterization of Raw Materials i. Cu Powder ii. SiCParticulates iii. E-Glass Fiber iv. Synthesis of Multiwalled Carbon Nanotubes (MWCNTs) 3.3 Synthesis and Characterization of Cu-Based Metal Matrix Composites Chapter 4 Results and Discussions 4.1 Mechanical Milling of Cu 4.2 Cu-SiCp Composite 4.3 CuE Glass fiber Composite 4.4 Cu-Multiwalled CNT Composite Chapter 5 Conclusions References Publications/Conferences Bio Data v xiii was done in order to study the fracture behaviour of the samples. The results show that the reinforcement is homogeneously distributed all over the Cu-matrix and the composites prepared show good bonding between the Cu-matrix and the reinforcement. Improvement in hardness and wear properties were observed with increase in the content of reinforcement in the composites.
Theoretical and Applied Fracture Mechanics, 2006
Tungsten/copper (W/Cu) particle reinforced composites were used to investigate the scaling effects on the deformation and fracture behaviour. The effects of the volume fraction and the particle size of the reinforcement (tungsten particles) were studied. W/Cu-80/20, 70/30 and 60/40 wt.% each with tungsten particle size of 10 lm and 30 lm were tested under compression and shear loading. Cylindrical compression specimens with different volumes (D S = H) were investigated with strain rates between 0.001 s À1 and about 5750 s À1 at temperatures from 20°C to 800°C. Axis-symmetric hat-shaped shear specimens with different shear zone widths were examined at different strain rates as well. A clear dependence of the flow stress on the deformed volume and the particle size was found under compression and shear loading. Metallographic investigation was carried out to show a relation between the deformation of the tungsten particles and the global deformation of the specimens. The size of the deformed zone under either compression or shear loading has shown a clear size effect on the fracture of the hat-shaped specimens.