Development of nanoinjector devices for electrospray ionization - tandem mass spectrometry (ESI-MSn) (original) (raw)
Related papers
Electrostatic-spray ionization mass spectrometry
Analytical chemistry, 2012
An electrostatic-spray ionization (ESTASI) method has been used for mass spectrometry (MS) analysis of samples deposited in or on an insulating substrate. The ionization is induced by a capacitive coupling between an electrode and the sample. In practice, a metallic electrode is placed close to but not in direct contact with the sample. Upon application of a high voltage pulse to the electrode, an electrostatic charging of the sample occurs leading to a bipolar spray pulse. When the voltage is positive, the bipolar spray pulse consists first of cations and then of anions. This method has been applied to a wide range of geometries to emit ions from samples in a silica capillary, in a disposable pipet tip, in a polymer microchannel, or from samples deposited as droplets on a polymer plate. Fractions from capillary electrophoresis were collected on a polymer plate for ESTASI MS analysis.
ELECTROPHORESIS, 2005
A multilayer poly(dimethylsiloxane) electrospray ionization emitter for sample injection and online mass spectrometric detection An ESI emitter made of poly(dimethylsiloxane) interfaces on-chip sample preparation with MS detection. The unique multilayer design allows both the analyte and the spray solutions to reside on the device simultaneously in discrete microfluidic environments that are spatially separated by a polycarbonate track-etched, nanocapillary array membrane (NCAM). In direct spray mode, voltage is applied to the microchannel containing a spray solution delivered via a syringe pump. For injection, the spray potential is lowered and a voltage is applied that forward biases the membrane and permits the analyte to enter the spray channel. Once the injection is complete, the bias potential is switched off, and the spray voltage is increased to generate the ESI of the injected analyte plug. Consecutive injections of a 10 mM bovine insulin solution are reproducible and produce sample plugs with limited band broadening and high quality mass spectra. Peptide signals are observed following transport through the NCAM, even when the peptide is dissolved in solutions containing up to 20% seawater. The multilayer emitter shows great potential for performing multidimensional chemical manipulations on-chip, followed by direct ESI with negligible dead volume for online MS analysis.
Analytical Chemistry, 2006
We have developed a new procedure for fabricating fusedsilica emitters for electrospray ionization-mass spectrometry (ESI-MS) in which the end of a bare fused-silica capillary is immersed into aqueous hydrofluoric acid, and water is pumped through the capillary to prevent etching of the interior. Surface tension causes the etchant to climb the capillary exterior, and the etch rate in the resulting meniscus decreases as a function of distance from the bulk solution. Etching continues until the silica touching the hydrofluoric acid reservoir is completely removed, essentially stopping the etch process. The resulting emitters have no internal taper, making them much less prone to clogging compared to, e.g., pulled emitters. The high aspect ratios and extremely thin walls at the orifice facilitate very low flow rate operation; stable ESI-MS signals were obtained for model analytes from 5-µmdiameter emitters at a flow rate of 5 nL/min with a high degree of interemitter reproducibility. In extensive evaluation, the etched emitters were found to enable approximately four times as many LC-MS analyses of proteomic samples before failing compared with conventional pulled emitters. The fabrication procedure was also employed to taper the ends of polymer monolith-containing silica capillaries for use as ESI emitters. In contrast to previous work, the monolithic material protrudes beyond the fused-silica capillaries, improving the monolithassisted electrospray process.
Microfabricated polymer injector for direct mass spectrometry coupling
…, 2002
This paper demonstrates the coupling of a plasma etched polymer microfluidic system with an electrospray mass spectrometer by generation of a nanospray. Taking advantage of the microtechnology processes and polymer properties, high volume production with good reproducibility of hydrophobic interfaces could be obtained. The nanospray was directly produced from the outlet of the plastic microfabricated chip positioned in front of the capillary entrance of the mass spectrometer. No chemical background due to the polymer has been observed under standard nanospray conditions. The performances of the spray as well as its efficiency have been demonstrated by flow measurements, stability establishment and tandem mass spectrometry experiment on angiotensin II. The spray was actuated without additional flow in methanol: water:acetic acid (50:49:1%) solution. A 40 fmol/mL detection limit could be reached.
Analytical Chemistry, 2007
In this study a nano-electrospray emitter is constructed by precisely positioning entrapped octadecylsilane (ODS) particles within a photoinitiated polymer at the exit aperture of a capillary. Following poly-merization, the microsphere/polymer hybrid material is able to withstand pressures greater than 4000 psi for 1 cm length of material. Smaller microspheres (3 µm) patterned at the exit aperture of a capillary generated the most sensitive/ stable electrospray from 100 to 1000 nL/min and moderately stable signal under 100 nL/min. Constant infusion of a standard PPG solution from a batch of eleven emitters resulted in a relatively small variance in total ion current (TIC) counts (8%). The entrapped microsphere emitter design yields an emitter that minimizes clogging and eliminates dead volume between the chromatographic bed and the electrospray emitter. The entrapped ODS microspheres can also be used for sample preparation prior to mass spectrometry (MS) analysis. We show the solidphase extraction and preconcentration of 20-700 fmol of a peptide (leucine enkephalin) prior to MS analysis on an emitter with 1 cm of entrapped microspheres.
Electrospray ionization mass spectrometry from discrete nanoliter-sized sample volumes
Rapid Communications in Mass Spectrometry, 2010
We describe a method for nanoelectrospray ionization mass spectrometry (nESI-MS) of very small sample volumes. Nanoliter-sized sample droplets were taken up by suction into a nanoelectrospray needle from a silicon microchip prior to ESI. To avoid a rapid evaporation of the small sample volumes, all manipulation steps were performed under a cover of fluorocarbon liquid. Sample volumes down to 1.5 nL were successfully analyzed, and an absolute limit of detection of 105 attomole of insulin (chain B, oxidized) was obtained. The open access to the sample droplets on the silicon chip provides the possibility to add reagents to the sample droplets and perform chemical reactions under an extended period of time. This was demonstrated in an example where we performed a tryptic digestion of cytochrome C in a nanoliter-sized sample volume for 2.5 h, followed by monitoring the outcome of the reaction with nESI-MS. The technology was also utilized for tandem mass spectrometry (MS/MS) sequencing analysis of a 2 nL solution of angiotensin I.
Ionization and transmission efficiency in an electrospray ionization—mass spectrometry interface
Journal of the American Society for Mass Spectrometry, 2007
The ionization and transmission efficiencies of an electrospray ionization (ESI) interface were investigated to advance the understanding of how these factors affect mass spectrometry (MS) sensitivity. In addition, the effects of the ES emitter distance to the inlet, solution flow rate, and inlet temperature were characterized. Quantitative measurements of ES current loss throughout the ESI interface were accomplished by electrically isolating the front surface of the interface from the inner wall of the heated inlet capillary, enabling losses on the two surfaces to be distinguished. In addition, the ES current lost to the front surface of the ESI interface was spatially profiled with a linear array of 340-m-diameter electrodes placed adjacent to the inlet capillary entrance. Current transmitted as gas-phase ions was differentiated from charged droplets and solvent clusters by measuring sensitivity with a single quadrupole mass spectrometer. The study revealed a large sampling efficiency into the inlet capillary (Ͼ90% at an emitter distance of 1 mm), a global rather than a local gas dynamic effect on the shape of the ES plume resulting from the gas flow conductance limit of the inlet capillary, a large (Ͼ80%) loss of analyte ions after transmission through the inlet arising from incomplete desolvation at a solution flow rate of 1.0 L/min, and a decrease in analyte ions peak intensity at lower temperatures, despite a large increase in ES current transmission efficiency. (J Am Soc Mass Spectrom 2007, 18, 1582-1590 E lectrospray ionization (ESI) has become a prominent ionization technique for a broad range of chemical and biological applications of mass spectrometry (MS) [1, 2] because of its ability to create intact, multiply charged gas-phase ions (from, e.g., biomolecules in solution) and its facile coupling with on-line separation techniques [such as liquid chromatography (LC)] [3-6]. The sensitivity of ESI-MS is largely determined by the effectiveness of producing gas-phase ions from analyte molecules in solution (ionization efficiency) and the ability to transfer the charged species from atmospheric pressure to the low-pressure region of the mass analyzer (transmission efficiency) [7-10].
Fabrication of enclosed SU-8 tips for electrospray ionization-mass spectrometry
ELECTROPHORESIS, 2005
We describe a novel electrospray tip design for MS which is fabricated completely out of SU-8 photoepoxy. A three-layer SU-8 fabrication process provides fully enclosed channels and tips. The tip shape and alignment of all SU-8 layers is done lithographically and is therefore very accurate. Fabrication process enables easy integration of additional fluidic functions on the same chip. Separation channels can be made with exactly the same process. Fluidic inlets are made in SU-8 during the fabrication process and no drilling or other postprocessing is needed. Channels have been fabricated and tested in the size range of 10 mm610 mm-50 mm6200 mm. Mass spectrometric performance of the tips has been demonstrated with both pressure-driven flow and EOF. SU-8 microtips have been shown to produce stable electrospray with EOF in a timescale of tens of minutes. With pressure driven flow stable spray is maintained for hours. Taylor cone was shown to be small in volume and well defined even with the largest channel cross section. The spray was also shown to be well directed with our tip design.
MEMS-Based Nanospray-Ionization Mass Spectrometer
2010
An electrospray-ionization mass spectrometer (ESI-MS) whose main components are all fabricated using silicon microelectromechanical systems (MEMS) techniques is demonstrated for the first time. The ion source consists of a microengineered alignment bench containing a V-groove mounting for a nanospray capillary, an ion-extraction electrode, and a pneumatic nebulizer. The vacuum interface consists of two plates, each carrying a 50-μm-diameter capillary, that are selectively etched and bonded together to provide a differentially pumped internal cavity. The quadrupole filter consists of a microfabricated frame that provides mountings for stainless-steel rods measuring 650 μm in diameter and 30 mm in length. Two different quadrupoles are compared: a first-generation bonded silicon device and a second-generation silicon-on-glass device with a Brubaker prefilter. Differential pumping of a MEMS component is demonstrated for the first time, atmospheric pressure ionization and ion transfer into vacuum are characterized, ESI-MS operation is demonstrated, and spectra are presented for a variety of compounds.
ELECTROPHORESIS, 2005
A soft on-column metal coating procedure for robust sheathless electrospray emitters used in capillary electrophoresis-mass spectrometry An on-column metal coating procedure was developed for sheathless electrospray emitters, based on Justus von Liebig's electroless silver mirror reaction followed by electrochemical deposition of gold onto the silver layer. The coating procedure is straightforward, mild, inexpensive, and can be performed with standard laboratory equipment. A long-term (600 h) stability investigation of the conductive coating was carried out by continuous electrospray in the positive electrospray mode, and no degradation in performance was found. The simplicity of the coating procedure and the robustness of the spray tips makes the spray tips highly suitable to couple delicate wall-coated or monolithic capillary columns to mass spectrometry. Peptide mixtures were separated by capillary electrophoresis and injected into either a Hadamardtransform time-of-flight mass analyzer or a commercial quadrupole mass analyzer using the described sheathless electrospray emitters. The performance was judged to be excellent.