NOVEL DESIGN OF COLLABORATIVE AUTOMATION PLATFORM USING REAL-TIME DATA DISTRIBUTION SERVICE MIDDLEWARE FOR AN OPTIMUM PROCESS CONTROL ENVIRONMENT (original) (raw)
Related papers
Oil and gas processing facilities utilize various process automation systems with proprietary controllers. As the systems age; older technologies become obsolete resulting in frequent premature capital investments to sustain their operation. This paper presents a new design of automation controller to provide inherent mechanisms for upgrades and/or partial replacement of any obsolete components without obligation for a complete system replacement throughout the expected life cycle of the processing facilities. The input/output racks are physically and logically decoupled from the controller by converting them into distributed autonomous process interface systems. The proprietary input/output communication between the conventional controller CPU and the associated input/output racks is replaced with standard real-time data distribution service middleware for providing seamless cross-vendor interoperable communication between the controller and the distributed autonomous process interface systems. The objective this change is to allow flexibility of supply for all controller's subcomponents from multiple vendors to safe guard against premature automation obsolescence challenges. Detailed performance analysis was conducted to evaluate the viability of using the standard real-time data distribution service middleware technology in the design of automation controller to replace the proprietary input/output communication. The key simulation measurements to demonstrate its performance sustainability while growing in controller's size based on the number of input/output signals, are communication latency, variation in packets delays, and communication throughput. The overall performance results confirm the viability of the new proposal as the basis for designing cost effective evergreen process automation solutions that would result in optimum total cost of ownership capital investment throughout the systems' life span. The only limiting factor is the selected network infrastructure.
Application of Distributed Control System in automation of Process Industries
2012
Abstract:The operation of modern day process plant cannot be visualized without the smart looking Distributed Control System (DCS) situated in control rooms. Process plant automation has evolved from pneumatics to electronics’ to DCS. Use of DCS leads to various advantages like the overall optimization, ease of operation and maintenance tasks, easy monitoring of more plant parameters and ensure tighter control on them. The field instrumentation and control system have to be integrated properly and must function optimally to achieve such a goal.
A Refinerys Distributed Process Control System
The paper describes the design philosophy taken into consideration for a refinery's distributed process control system. It ensures reliability, availability and maintenability. The entire DPCS incudes 9 control centers. The architecture of the field control station is discussed. The memory copy and data transfer ensures smooth transfer to the back-up controller. Redundancy is enhanced by customer additional requirements, such as communication bus redundancy, operational grouping and duplication of displays. The signals interface to the DPCS and the man-machine interface are presented. Industrial environment realistic problems are incuded.
IJERT-Real-Time Simulation Of A Networked-Process Control System For A Chemical Industry
International Journal of Engineering Research and Technology (IJERT), 2012
https://www.ijert.org/real-time-simulation-of-a-networked-process-control-system-for-a-chemical-industry https://www.ijert.org/research/real-time-simulation-of-a-networked-process-control-system-for-a-chemical-industry-IJERTV1IS10077.pdf This paper analyzes the real-time simulation of a networked-process control system for a chemical industry. The system has four Access layer servers connected to several loads via four Controller Area Networks (CANs) using Proteus software (Version 7.6). A typical industrial application used as a case study for this work is a chemical industry which produces Vinyl Chloride, a major raw material used in the production of Poly Vinyl Chloride (PVC) products. The system network was developed in a Proteus environment by interconnecting the Access layer servers, Ethernet Controller (which establishes a Local Area Network, LAN), and CAN Controllers. This study was implemented in the control of the industrial processes from the Access layer servers in a real-time environment. This was achieved by replacing the Ethernet controller with a programmed AT89C55 microcontroller to achieve the same switching logic, and this confirmed the workability of the system in a real-life situation.
Process Control Program as an Element of Distributed Control System
2014
Abstract. Monitoring and control of technological processes in many production units demands transfer of infor-mation and interaction with the process from remote distances. For this purpose, the process control systems have been designed and developed. In the first project phase, the separate production lines were covered by independent control systems. In the second phase, the individual control systems were interconnected in a large heterogeneous industrial network, forming the distributed control system (DCS). This paper presents results of development of specific hard-ware and software solutions for monitoring of technological processes, with special regards to communication systems structure.