Multiphysics Simulation of Low-Amplitude Acoustic Wave Detection by Piezoelectric Wafer Active Sensors Validated by In-Situ AE-Fatigue Experiment (original) (raw)
Related papers
Fatigue crack detection in thick steel structures with piezoelectric wafer active sensors
This paper presents a set of numerical and experimental results on the use of guided waves for structural health monitoring (SHM) of crack growth during a fatigue test in a thick steel plate used for civil engineering application. The capability of embedded piezoelectric wafer active sensors (PWAS) to perform in situ nondestructive evaluation (NDE) is explored. Numerical simulation and experimental tests are used to prove that PWAS can perform active SHM using guided wave pitch-catch method and passive SHM using acoustic emission (AE). Multi-physics finite element (MP-FEM) codes are used to simulate the transmission and reception of guided waves in a 1-mm plate and their diffraction by a through hole. The MP-FEM approach permitted that the input and output variables be expressed directly in electric terms while the two-ways electromechanical conversion was done internally in the MP-FEM formulation. The analysis was repeated for several hole sizes and a damage index performances was tested. AE simulation was performed with the MP-FEM approach in a 13-mm plate in the shape of the compact tension (CT) fracture mechanics specimen. The AE event was simulated as a pulse of defined duration and amplitude. The electrical signal measured at a receiver PWAS was simulated. Daubechies wavelet transform was used to process the signal and identify its Lamb modes and FFT frequency contents. Experimental tests were performed with PWAS transducers acting as passive receivers of AE signals. The 8-mm thick flange of an I beam was instrumented on one side with PWAS transducers and on the other side with conventional AE transducers (PAC R15I) acting as comparison witnesses. An AE source was simulated using 0.5mm pencil lead breaks; the PWAS transducers were able to pick up AE signal with good strength. Subsequently, PWAS transducers and R15I sensors were applied to a 13-mm CT specimen subjected to accelerated fatigue testing. The PWAS and R15I transducers signals were collected with PAC data acquisition system using the AE-win software. Comparative results of AE hits and source localization from the PWAS and R15I sensors are given. Active sensing in pitch catch mode was applied between the PWAS transducers installed on the CT specimen and damage indexes were calculated and correlated with physical crack growth as measured optically. The paper finishes with summary, conclusion, and suggestions for further work.
Journal of Intelligent Material Systems and Structures
In this article, the effect of the acoustic emission sensor on the acoustic emission waveforms from fatigue crack growth in a thin aerospace specimen is presented. In situ acoustic emission fatigue experiments were performed on the test coupons made of aircraft grade aluminum plate. Commercial Mistras S9225 acoustic emission sensor and piezoelectric wafer active sensor were used to capture the acoustic emission waveforms from the fatigue crack. It has been shown that the piezoelectric wafer active sensor transducer successfully captured the fatigue crack–related acoustic emission waveforms in the thin plate. The piezoelectric wafer active sensor transducer seems to capture more frequency information of the acoustic emission waveform than the conventional acoustic emission sensor in this particular application. We have also shown the evolution of the acoustic emission waveforms as the fatigue crack grows. The signatures of the fatigue crack growth were captured by the evolution of th...
This paper presents numerical and experimental results on the use of guided waves for structural health monitoring (SHM) of crack growth during a fatigue test in a thick steel plate used for civil engineering application. Numerical simulation, analytical modeling, and experimental tests are used to prove that piezoelectric wafer active sensor (PWAS) can perform active SHM using guided wave pitch-catch method and passive SHM using acoustic emission (AE). AE simulation was performed with the multi-physic FEM (MP-FEM) approach. The MP-FEM approach permits that the output variables to be expressed directly in electric terms while the two-ways electromechanical conversion is done internally in the MP-FEM formulation. The AE event was simulated as a pulse of defined duration and amplitude. The electrical signal measured at a PWAS receiver was simulated. Experimental tests were performed with PWAS transducers acting as passive receivers of AE signals. An AE source was simulated using 0.5-mm pencil lead breaks. The PWAS transducers were able to pick up AE signal with good strength. Subsequently, PWAS transducers and traditional AE transducer were applied to a 12.7-mm CT specimen subjected to accelerated fatigue testing. Active sensing in pitch catch mode on the CT specimen was applied between the PWAS transducers pairs. Damage indexes were calculated and correlated with actual crack growth. The paper finishes with conclusions and suggestions for further work.
Steel bridge fatigue crack detection with piezoelectric wafer active sensors
2010
Piezoelectric wafer active sensors (PWAS) are well known for its dual capabilities in structural health monitoring, acting as either actuators or sensors. Due to the variety of deterioration sources and locations of bridge defects, there is currently no single method that can detect and address the potential sources globally. In our research, our use of the PWAS based sensing has the novelty of implementing both passive (as acoustic emission) and active (as ultrasonic transducers) sensing with a single PWAS network. The combined schematic is using acoustic emission to detect the presence of fatigue cracks in steel bridges in their early stage since methods such as ultrasonics are unable to quantify the initial condition of crack growth since most of the fatigue life for these details is consumed while the fatigue crack is too small to be detected. Hence, combing acoustic emission with ultrasonic active sensing will strengthen the damage detection process. The integration of passive acoustic emission detection with active sensing will be a technological leap forward from the current practice of periodic and subjective visual inspection, and bridge management based primarily on history of past performance.
Recent Advances in Piezoelectric Wafer Active Sensors for Structural Health Monitoring Applications
Sensors
In this paper, some recent piezoelectric wafer active sensors (PWAS) progress achieved in our laboratory for active materials and smart structures (LAMSS) at the University of South Carolina: http: //www.me.sc.edu/research/lamss/ group is presented. First, the characterization of the PWAS materials shows that no significant change in the microstructure after exposure to high temperature and nuclear radiation, and the PWAS transducer can be used in harsh environments for structural health monitoring (SHM) applications. Next, PWAS active sensing of various damage types in aluminum and composite structures are explored. PWAS transducers can successfully detect the simulated crack and corrosion damage in aluminum plates through the wavefield analysis, and the simulated delamination damage in composite plates through the damage imaging method. Finally, the novel use of PWAS transducers as acoustic emission (AE) sensors for in situ AE detection during fatigue crack growth is presented. Th...
Monitoring of acoustic emission activity using thin wafer piezoelectric sensors
SPIE Proceedings, 2014
Acoustic emission (AE) is a well-known technique for monitoring onset and propagation of material damage. The technique has demonstrated utility in assessment of metallic and composite materials in applications ranging from civil structures to aerospace vehicles. While over the course of few decades AE hardware has changed dramatically with the sensors experiencing little changes. A traditional acoustic emission sensor solution utilizes a thickness resonance of the internal piezoelectric element which, coupled with internal amplification circuit, results in relatively large sensor footprint. Thin wafer piezoelectric sensors are small and unobtrusive, but they have seen limited AE applications due to low signalto-noise ratio and other operation difficulties. In this contribution, issues and possible solutions pertaining to the utility of thin wafer piezoelectrics as AE sensors are discussed. Results of AE monitoring of fatigue damage using thin wafer piezoelectric and conventional AE sensors are presented
Steel bridge fatigue crack detection with piezoelectric wafer active sensors
Sensors and Smart Structures Technologies for Civil, Mechanical, and Aerospace Systems 2010, 2010
Piezoelectric wafer active sensors (PWAS) are well known for its dual capabilities in structural health monitoring, acting as either actuators or sensors. Due to the variety of deterioration sources and locations of bridge defects, there is currently no single method that can detect and address the potential sources globally. In our research, our use of the PWAS based sensing has the novelty of implementing both passive (as acoustic emission) and active (as ultrasonic transducers) sensing with a single PWAS network. The combined schematic is using acoustic emission to detect the presence of fatigue cracks in steel bridges in their early stage since methods such as ultrasonics are unable to quantify the initial condition of crack growth since most of the fatigue life for these details is consumed while the fatigue crack is too small to be detected. Hence, combing acoustic emission with ultrasonic active sensing will strengthen the damage detection process. The integration of passive acoustic emission detection with active sensing will be a technological leap forward from the current practice of periodic and subjective visual inspection, and bridge management based primarily on history of past performance. In this study, extensive laboratory investigation is performed supported by theoretical modeling analysis. A demonstration system will be presented to show how piezoelectric wafer active sensor is used for acoustic emission. Specimens representing complex structures are tested. The results will also be compared with traditional acoustic emission transducers to identify the application barriers.
Advances in Civil Engineering, 2012
Monitoring of fatigue cracking in steel bridges is of high interest to many bridge owners and agencies. Due to the variety of deterioration sources and locations of bridge defects, there is currently no single method that can detect and address the potential sources globally. In this paper, we presented a dual mode sensing methodology integrating acoustic emission and ultrasonic wave inspection based on the use of low-profile piezoelectric wafer active sensors (PWAS). After introducing the research background and piezoelectric sensing principles, PWAS crack detection in passive acoustic emission mode is first presented. Their acoustic emission detection capability has been validated through both static and compact tension fatigue tests. With the use of coaxial cable wiring, PWAS AE signal quality has been improved. The active ultrasonic inspection is conducted by the damage index and wave imaging approach. The results in the paper show that such an integration of passive acoustic emission detection with active ultrasonic sensing is a technological leap forward from the current practice of periodic and subjective visual inspection and bridge management based primarily on history of past performance.
Smart Materials and Structures, 2006
Structural damage detection is one of the major maintenance activities in a wide range of industries. A variety of different methods have been developed for detection of fatigue cracks in metallic structures over the last few decades. This includes techniques based on stress/acoustic waves propagating in monitored structures. Classical ultrasonic techniques used in nondestructive testing and evaluation are based on linear amplitude and/or phase variations of reflected, transmitted or scattered waves. In recent years a range of different techniques utilizing nonlinear phenomena in vibration and acoustic signals have been developed. It appears that these techniques are more sensitive to damage alterations than other techniques used for damage detection based on linear behaviour. The paper explores the use of low-profile piezoceramic actuators with low-frequency excitation in nonlinear acoustics. The method is used to detect a fatigue crack in an aluminium plate. The results are compared with modal/vibration excitation performed with an electromagnetic shaker. The study shows that piezoelectric excitation with surface-bonded low-profile piezoceramic transducers is suitable for crack detection based on nonlinear acoustics.
International Journal of Aerospace Engineering
Piezoelectric transducers have a long history of applications in nondestructive evaluation of material and structure integrity owing to their ability of transforming mechanical energy to electrical energy and vice versa. As condition based maintenance has emerged as a valuable approach to enhancing continued aircraft airworthiness while reducing the life cycle cost, its enabling structural health monitoring (SHM) technologies capable of providing on-demand diagnosis of the structure without interrupting the aircraft operation are attracting increasing R&D efforts. Piezoelectric transducers play an essential role in these endeavors. This paper is set forth to review a variety of ingenious ways in which piezoelectric transducers are used in today’s SHM technologies as a means of generation and/or detection of diagnostic acoustic waves.