GEOMETRIC QUALITY ANALYSIS AND PROCESS CONTROL FOR ULTRA-PRECISION LASER MICROMACHINING (original) (raw)
Related papers
Theoretical aspects of Laser micro machining and its role in new industrial revolution
CETMIE-2017, 2017
A laser micro machining is becoming popular in the industrial world due to its unique characteristics. Miniaturization has changed the path of machining of various materials. The various properties such as high peak intensity, precision, non-thermal interaction and flexibility make micro-laser machining a well accepted tool of machining. The major advantage of laser micro machining is lower aspect ratio, precise laser cutting zone, flexibility and fast processing. The objective of this review article is to analyze the various laser micromachining techniques, challenges in application, research carried out and their characteristics. This article also depicts the comparison between different laser micro-machining sources which have direct impact on the quality of machined surfaces. A comparison between pico-second, micro-second and nano-second laser has been explained with respect to fluence ablation in the machining zone.
Statistical and Numerical Approaches for Modeling and Optimizing Laser Micromachining Process-Review
Reference Module in Materials Science and Materials Engineering, 2019
This chapter presents the modelling and optimization techniques commonly used in engineering applications especially in Laser Micromachining process. Design of Experiment DOE (Response Surface Method and Taguchi), Artificial Neural Network (ANN), Genetic Algorithm (GA), and Particle swarm optimization (PSO) and mixed techniques are explained briefly. Furthermore, a review of laser micromachining processes parameters optimization was studied. Recent researches which used different approaches for modelling and optimization was presented.
Development and Modeling of Laser Micromachining Techniques
Laser micromachining has great potential as a MEMS (micro-electromechanical systems) fabrication technique because of its materials flexibility and 3D capabilities. The machining of deep polymer structures with complex, well-defined surface profiles is particularly relevant to micro-fluidics and micro-optics. This paper presents the use of projection ablation methods to fabricate structures and devices aimed at these application areas. A better understanding of the mechanisms of thermodynamics and heat transfer in MEMS is desired to improve the thermal performance of MEMS due to the importance of these physical processes. Ablation rate of the laser depends on temperature, the material properties and accumulation of heat in the work material. In consequence, to control the laser processing, thermal distribution of the sample has to be determined, which can be made by modeling of laser ablation. By using such modeling tool, proper laser parameters can be determined easier and faster. Geometry of the domain under investigation varies during the simulation, because laser pulses remove material from the sample, thermal effects, photochemical and other phenomena still exist and so the modeling of laser ablation is a specialised problem. A two dimensional finite element model is developed in this work for laser ablation of polymers. Model has been further modified for fabrication of curved sufaces utilized in MEMS applications.
This paper focuses on modelling and optimizing process parameters in pulsed laser micro-machining. Use of continuous wave or pulsed lasers to perform micro-machining of 3-D geometrical features on difficult-to-cut metals is a feasible option due the advantages offered such as tool-free and high precision material removal over conventional machining processes. Despite these advantages, pulsed laser micro-machining is complex, highly dependent upon material absorption reflectivity, and ablation characteristics. Selection of process operational parameters is highly critical for successful laser micro-machining. For this reason, it is necessary to clearly understand the process parameter influence on material removal in complex 3-D geometrical features. A set of designed experiments are carried in a pulsed Nd:YAG laser system using H13 hardened tool steel as work material. Several T-shaped deep features with straight and tapered walls have been machining as representative mold cavities ...
2021
Laser beam micromachining (LBMM) and micro electro-discharge machining (µEDM) based sequential micromachining technique, LBMM-µEDM has drawn signi cant research attention to utilizing the advantages of both methods, i.e. LBMM and µEDM. In this process, a pilot hole is machined by the LBMM and subsequently nishing operation of the hole is carried out by the µEDM. This paper presents an experimental investigation on the stainless steel (type SS304) to observe the effects of laser input parameters (namely laser power, scanning speed, and pulse frequency) on the performance of the nishing technique that is the µEDM in this case. The scope of the work is limited to 1-D machining, i.e. drilling micro holes. It was found that laser input parameters mainly scanning speed and power in uenced the output performance of µEDM signi cantly. Our study suggests that if an increased scanning speed at a lower laser power is used for the pilot hole drilling by the LBMM process, it could result in signi cantly slower µEDM machining time. On the contrary, if the higher laser power is used with even the highest scanning speed for the pilot hole drilling, then µEDM processing time was faster than the previous case. Similarly, µEDM time was also quicker for LBMMed pilot holes machined at low laser power and slow scanning speed. Our study con rms that LBMM-µEDM based sequential machining technique reduces the machining time, tool wear and instability (in terms of short circuit count) by a margin of 2.5 x, 9 x and 40 x respectively in contrast to the pure µEDM process without compromising the quality of the holes.
Some Results of Finite Element Modelling of Laser Beam Micro-Machining Aided by Ultrasonics
The paper deals with some preliminary results from modelling through finite element analysis of material removal mechanism of laser beam micro-machining at drilling and contouring of hardened tool steel X210Cr12. A comparison is achieved between laser beam machining with and without ultrasonics aiding in terms of material volume removal. Different cases were studied: micro-drilling, linear contouring, trepanning, and spiral contouring. The influence of initial roughness and laser spot path on material removal mechanism is analyzed. The finite element analysis results are compared to experimental data. A 2D and 3D modelling was approached for micro-drilling and respective micro-contouring, in agreement to available reference data.
Model for ultrafast laser micromachining
Laser-based Micro- and Nanoprocessing XII
Ablation by ultrafast lasers results from a series of complex nonlinear phenomena of absorption and transfer of energy that take place in the surfaces of materials upon irradiation. Provided that a good window of processing parameters is chosen, the resulting thermal effects are in general negligible, making ultrafast lasers excellent micromachining tools applicable to most types of materials. It is thus beneficial to understand how ablation is affected by the laser processing parameters and the material properties, in order to optimize the micromachining processes. We propose an engineering model to estimate the dimensions of ablation, taking into account on the one hand the material properties such as the ablation threshold, penetration depth and the refractive index and, on the other hand, the processing parameters namely the pulse energy and beam diameter, scanning speed, repetition rate and angle of incidence. The model considers as well the effects of incubation, changes of topography during multi-pulse irradiation, surface reflectivity and Gaussian beam diameter variation with the distance to the focal plane. The model is able to simulate the profiles of ablation surfaces produced by normal or tilted laser beam, either for spot, line and area processing. The results obtained are validated by comparison to the ones obtained experimentally. Both the model and the experiments focus on stainless steel. The predictions of the model also allow for the optimization of the micromachining process, both energy and time wise.
Dynamic Process Behavior in Laser Chemical Micro Machining of Metals
Journal of Manufacturing and Materials Processing, 2018
Laser chemical machining (LCM) is a non-conventional processing method that enables a smooth and precise micro structuring of metallic surfaces. However, a high-quality removal is limited to a laser power window of some 100 mW. This is due to the high sensibility to removal disturbances, such as the deposition of metallic salts and oxides. In this work, the dynamic process behavior around the transition from a disturbance-free to a disturbed removal is investigated for the laser chemical machining of titanium (3.7024) and stainless steel (AISI 304) in different phosphoric acid solutions. Therefore, the removal cavities are recorded using confocal scanning microscopy and characterized regarding width, depth and quality in dependence of the laser power, feed velocity and electrolyte concentration. While the removal characteristics within the disturbance-free regime are found to be material-independent, the disturbed regime is strongly dependent on the tendency of the material to gas b...
New Method for Nanosecond Laser Machining
Journal of Laser Micro/Nanoengineering, 2012
The technique of micro-machining assisted by laser is the most recent and flexible process for the design of complex devices. To be able to micro-machine hard materials with precision it is necessary to study the parameters that control and limit the capabilities of this laser process. Several articles have shown that if it applies a lot of energy in a localized area there are hot-affected zones (HAZ), even when a femtosecond laser is used. Hence, the challenge in the laserbased micromachining is to improve the quality of machining, i.e. depleting the HAZ in the prototypes. In this work, changing the optical properties of the substrate, good quality silicon micro-machining has been obtained with a nanosecond Q-switched laser.