The Effects of Parasitics on Distributed High-Pass MOSFET Filters (original) (raw)
Related papers
FDNR switched-capacitor filters insensitive to parasitic capacitances
IEEE Transactions on Circuits and Systems, 1982
Absrract-The switched-capacitor transconductance is used to simulate a new FDNR element which is relatively insensitive to parasitic capacitances and requires few components. The element is used in the switched-capacitor simulation of a fifth-order LC low-pass filter. It is shown that the influence of other switched parasitic capacitances, occurring in the filter due to the switches, can be eliminated by predistortion and that the resulting network is, except for a flat loss, equivalent to the original ideal network. Computational and experimental results, obtained on a network with discrete components, are presented. I.
A new MOSFET-C universal filter structure for VLSI
IEEE Journal of Solid-State Circuits, 1988
Alistract-A new continuous-time all-MOS universal filter structure is proposed. The new structure is based on the MOSFET-C design approach. It achieves complete MOS nonlinearity cancellation and does not require the use of fully balanced op amps. General topological requirements that are necessary for the conversion of active-RC prototypes to MOSFET-C counterparts, such that MOS nonlinearity cancellation is achieved, are established. Accordingly, a new universal active-RC prototype filter structure, which meets the necessary requirements, is presented and its MOSFET-C version is developed. Nonideal effects that may degrade the performance at high frequency are discussed and ways for improvement are proposed. Results obtained from a test chip have verified the viability of the proposed structure. The chip is an implementation of a MOSFET-C universal filter in a 3.5-pm CMOS process. The filter is successfully tuned over a wide range of pole frequencies (0 + 100 kHz) using op amps with a measured gain bandwidth (GB) of only 1.2 MHz.
Impact of MOSFET parameters on its parasitic capacitances
Proceedings of the 6th WSEAS Int. Conf. on Electronics, Hardware, Wireless and Optical Communications, Corfu Island, Greece, 2007
The aim of this paper is to calculate the MOSFET parasitic capacitances, and then based on the results obtained we can further see the impact of MOSFET physical parameters on these parasitic capacitances. These capacitances have a direct impact in the speed of operation of MOSFET circuits. Therefore, in order to increase the speed of operation, it is necessary that the parasitic capacitances are reduced to a minimum possible level that the technological process allows. We have analyzed the gate capacitance effect and junction capacitances as a function of the MOSFET dimensions.
Design of Second Order Low Pass and High Pass Filter using Double Gate MOSFET based OTA
OTA-C filters are one of the most widely used as continuous time filters. It is because they are fast active integrators, provides low-power operation and tuning of the filter characteristics at higher frequencies. At high frequencies, the OP AMP based active filters has limited performance. We cannot change the values of resistors and inductors but OTA-C filter provides ability to change their values by changing the transconductance of OTA. Second order low and high pass filter structures have widespread applications. The double gate MOSFETs show better performance in the nanometer range of operation. Because it has better control over short channel effects (SCE's) and other scaling related problems like gate leakage, sub-threshold conduction. Double gate MOSFET is four terminal device and back gate can be used for biasing which can tune the characteristics of circuit. This will provide additional advantage of low power and reduced area. This paper presents second order low pass and high pass filter based on double gate OTA for VHF and UHF frequency applications. The proposed filter consists of two OTAs and two capacitors. This filter shows low sensitivity to passive components, low component count and ease in design. The simulation results shows pass band frequency of 14MHz and power consumption of 153.4 µwatt. The simulations are done using Tanner EDA version 13.0 at 90nm technology.
Proceedings of The IEEE, 1987
This section is intended primarily for rapid dissemination of brief reports on new research results within the scope of the lEEE members. Contributions are reviewed immediately, and acceptance is determined by timeliness and importance of the subject, and brevity and clarity of the presentation. Research letters must contain a clear concise statement of the problem studied, identify new results, and make evident their utility, importance, or relevance to electrical engineering and science. Key references to related literature must be given.
Universal current-mode filters and parasitic impedance effects on the filter performances
International Journal of Circuit Theory and Applications, 2008
In this letter, two universal current-mode (CM) filters for simultaneously realizing low-pass, band-pass and high-pass characteristics are proposed. Both of the presented filters can also realize notch and all-pass responses with interconnection of the relevant output currents. They employ second-generation currentcontrolled conveyors (CCCIIs) and only grounded capacitors. They also have low active and passive element sensitivities along with electronically adjustable angular resonance frequency ( 0 ) and quality factor (Q). Based on the first developed filter, the parasitic impedance effects of the conveyors on the filter performances are investigated in detail. Simulation results using SPICE simulation program are included to verify the theory. Some CM filter topologies using OAs have been reported . Also, a large number of CM single-input three-output (SITO) second-order filters have been presented in the literature . The proposed filter in [4] employs only grounded passive elements but they need seven secondgeneration CCs (CCIIs). It is also possible to decrease the number of active components in cost of using floating passive elements as presented in . However, the use of only one or two single-output CCs in SITO filters prevents to obtain high-output impedance for all output currents . Another approach for the design of CM filters is to use multi-output CCs and two identical input currents . However, such filters require an extra active device for implementing identical input currents.
Circuits Systems and Signal Processing, 2001
A new CMOS realization of the differential current voltage conveyor (DCVC) is introduced. The properties of the DCVC are shown to be suitable for very large-scale integration applications employing metal oxide semiconductor transistors operating in an ohmic region. A novel voltage-mode integrator is introduced. Detailed analysis of the parasitic capacitances is included. Voltage-mode continuous-time filters that benefit from the current processing capabilities at the input terminals of the DCVC are presented. Selfcompensation of the proposed circuits is also presented. The effectiveness of the proposed circuits is demonstrated through HSPICE simulations based on the AMI 1.2/_~m N-well level 3 parameters.
Analysis of simple two-capacitor low-pass filters
2003
Abstract The performance of typical low-pass capacitor filters is limited by the mutual inductance between the input and output sides of the filter. This paper describes how two appropriately spaced capacitors can be used to construct a low-pass filter with significantly better high-frequency performance than a one-capacitor filter. Laboratory measurements and numerical simulations are used to quantify the mutual inductance and compare the performance of one-and two-capacitor low-pass filters.
Design and Analytical Study of Strays-Insensitive Switched-Capacitor Filters
Active and Passive Electronic Components, 1996
Use of analog circuit elements in active networks have become very common and the demand for their miniaturization is increasing day by day. Though several methods are available for the miniaturization of these elements through large scale integration on single chips, the performance is not very satisfactory in low-frequency applications, due to the presence of parasitic capacitance that is comparable to the capacitance of active elements. As a result, the desired response gets deviated and also noise is involved. In this paper, an attempt has been made to devise methods for the elimination or reduction of the influence of these parasitic capacitances on filter circuits.