Transformer Frequency Response Modeling Using Genetic Algorithm (original) (raw)
Related papers
Identification of transient model parameters of transformer using genetic algorithm
2010
In this paper, a black box model has been proposed in order to analyze transformer transient behaviors. This model is capable to reveal the transformer impedance (or admittance) characteristics up to 1.2 MHz observed from transformer terminals under various connections. Also, this model is powerful to display the characteristic of traveling wave toward consumer. In this contribution, a 6300/420V, 2500KVA transformer is used to investigate. The parameters of represented model have been computed by use of the practical measurements and also genetic algorithm method. Comparisons between the calculated and the measured results are satisfactory and confirm the good precision of the represented method in order to estimate model parameters.
Extraction of Parameters of Planar Transformers Using Genetic Algorithms
2007
The planar inductors and transformers are widely used passive components in RF circuits. The precise RF model development of inductor and transformer elements is an important step in the design of microelectronic circuits for RF applications. The models can be extracted and optimized using Genetic Algorithms (GA). A general approach for parameter extraction of the model parameters for planar transformers is proposed and compared with the results, obtained via similar methods [1,2,3,4,5]. The presented extraction approach is applicable and with a good accuracy. It is based on computer models, developed using the possibilities of MATLAB and GA toolbox [6]. GA programs are designed using the MATLAB GA toolbox for parameter extraction of the model parameters of planar transformers. A verification of the obtained results for the extracted model parameters is done by comparison of the simulation results obtained using PSpice of the corresponding model and measurement data in [4].
Estimation of the Equivalent Circuit Parameters in Transformers Using Evolutionary Algorithms
Mathematical and Computational Applications
The conventional methods of parameter estimation in transformers, such as the open-circuit and short-circuit tests, are not always available, especially when the transformer is already in operation and its disconnection is impossible. Therefore, alternative (non-interruptive) methods of parameter estimation have become of great importance. In this work, no-interruption, transformer equivalent circuit parameter estimation is presented using the following metaheuristic optimization methods: the genetic algorithm (GA), particle swarm optimization (PSO) and the gravitational search algorithm (GSA). These algorithms provide a maximum average error of 12%, which is twice as better as results found in the literature for estimation of the equivalent circuit parameters in transformers at a frequency of 50 Hz. This demonstrates that the proposed GA, PSO and GSA metaheuristic optimization methods can be applied to estimate the equivalent circuit parameters of single-phase distribution and powe...
An Evolutionary Computation Solution to Transformer Design Optimization Problem
7th International Conference on Electrical and Electronics Engineering Research (CIIIEE), 2010
The transformer design optimization (TDO) is a complex constrained mixed-integer non-linear programming problem with discontinuous objective function. This paper proposes an innovative method combining genetic algorithm (GA) and finite element method (FEM) for the solution of TDO problem. The main contributions of the proposed method are: (i) introduction of an innovative recursive GA with a novel external elitism strategy associated with variable crossover and mutation rates resulting in an improved GA, (ii) adoption of two particular finite element models of increased accuracy and high computational speed for the validation of the optimal design by computing the no-load loss and impedance, and (iii) combination of the innovative recursive GA with the two particular finite element models resulting in a proposed GAFEM model that finds the global optimum, as concluded after several tests on actual transformer designs, while other existing methods provided suboptimal solutions that are 3.1% to 5.8% more expensive than the optimal solution.
Transformer Core Parameter Identification Using Frequency Response Analysis
2010
Abstract We present a novel model-based approach for parameter identification of a laminated core, such as magnetic permeability and electrical conductivity, of power transformers on the basis of frequency response analysis (FRA) measurements. The method establishes a transformer core model using the duality principle between magnetic and electrical circuits for parameter identification with genetic algorithms.
PCB-planar transformers equivalent circuit model identification using genetic algorithm
International Journal of Modelling, Identification and Control, 2018
Planar passive components are interesting solutions for the design of integrated power converters. Models of planar magnetic devices are still not available in simulator tools. There is, thus, a specific limitation during the design process of integrated power systems. In this paper, an equivalent circuit model for a planar transformer is proposed. This physics-based model includes the magnetising and leakage inductance, the parasitic capacitance and the ohmic loss effects. The skin and proximity effects in primary and secondary windings are modelled by the ladder R-L network. The ladder parameters are identified by minimising the function between experimental and simulation results using the genetic algorithm. The planar transformer simulation results have been tested and favourably compared with practical measurements and 3D finite element method simulation of a large number of transformer designs. A comparative study between experimental data and simulation results is established and found excellent agreement.
The transformer manufacturing cost minimisation (TMCM), also known as transformer design optimisation, is a complex constrained mixed-integer non-linear programming problem with discontinuous objective function. This paper proposes an innovative method combining genetic algorithm (GA) and finite element method (FEM) for the solution of TMCM problem. The main contributions of the proposed method are: (a) introduction of an innovative recursive GA with a novel external elitism strategy associated with variable crossover and mutation rates resulting in an improved GA, (b) adoption of two particular finite element models of increased accuracy and high computational speed for the validation of the optimal design by computing the no-load loss and impedance and (c) combination of the innovative recursive GA with the two particular finite element models resulting in a proposed GA-FEM model that finds the global optimum, as concluded after several tests on actual transformer designs, while other existing methods provided suboptimal solutions that are 3.1 – 5.8% more expensive than the optimal solution.
The aim of this paper is to present an alternative methodology for obtaining rational functions that suitably approximate the frequency response of power system networks. Through this methodology, part of the system under analysis can be replaced by a Frequency Dependant Network Equivalent (FDNE), which simplifies system representation and makes possible the accurate evaluation of large power networks. The methodology is based on Evolutionary Algorithms (EAs). Basically, different set of values for the rational function parameters are simultaneously assessed. The EA suitably changes the values for the function parameters, decreasing the RMS error between the system's original frequency response and the response provided by the rational function. The results obtained through the proposed methodology were compared with the ones obtained through the Vector Fitting methodology, which is the common approach used for solving similar problems.
A synergetic neural network-genetic scheme for optimal transformer construction
2002
In this paper, a combined neural network and an evolutionary programming scheme is proposed to improve the quality of wound core distribution transformers in an industrial environment by exploiting information derived from both the construction and transformer design phase. In particular, the neural network architecture is responsible for predicting transformer iron losses prior to their assembly, based on several actual core measurements, transformer design parameters and the specific core assembling. A genetic algorithm is applied to estimate the optimal core arrangement, (i.e. the way of core assembling) that yields a set of three-phase transformers of minimal iron losses. The minimization is performed by exploiting information derived from the neural network model resulting in a synergetic neural network-genetic algorithm scheme. After the transformer construction, the prediction accuracy of the neural network model is evaluated. If accuracy is poor, a weight adaptation algorithm is applied to improve the prediction performance. For the weight updating, both the current and the previous network knowledge are taken into account. Application of the proposed neural network-genetic algorithm scheme to our industrial environment indicates a significant reduction in the variation between the actual and the designed transformer iron losses.
Design Optimization of High-Frequency Power Transformer by Genetic Algorithm and Simulated Annealing
International Journal of Electrical and Computer Engineering (IJECE), 2011
This paper highlights the transformer design optimization using genetic algorithm (GA) and simulated annealing (SA). Any optimization problem, a given objective function is to be minimized keeping in view the constraints. Similarly, transformer design optimization problem involves minimizing the total mass (or cost) of the core and wire material by satisfying constraints imposed by international standards and transformer user specification. The constraints include appropriate limits on efficiency, voltage regulation, temperature rise, no-load current and winding fill factor. The design optimizations seek a constrained minimum mass (or cost) solution by optimally setting the transformer geometry parameters and require magnetic properties. This paper solves the said design problem by using genetic algorithm (GA) and simulated annealing (SA) techniques. The results of geometric programming (GP) technique have been compared with the results obtained by applying GA and SA techniques. It is quite evident from the results that the dimensions as well as mass of copper and core have been reduced in comparison to GP using same set of constraints. Therefore, the paper presents improved design of power transformer by these two techniques. The results of GA and SA have been obtained using optimization tool box MATLAB Release 9.1 which have not been applied for power transformer design so far. First it provides efficient and reliable solution for the design optimization problem with several variables. Second, it guaranteed that the obtained solution is global optimum. Hence paper demonstrates a better and efficient solution to high frequency power transformer design.