Laser Peening on Aluminum Alloy 7049 Using Black Paint Surface Coating (original) (raw)
Related papers
Nd-YAG Laser surface hardening of a PM-M3 steel
A powder metallurgy (PM) M3, class 2, high-speed steel was subjected to surface hardening with a Nd-YAG laser. A variety of laser operating conditions, including beam size, power and travel speed, and various starting microstructural conditions, including as-annealed, as-quenched and tempered, were evaluated. Surface hardening and melting were sensitive to operating and starting conditions, but higher laser heat input into quench and tempered specimens produced significantly higher hardness, HV100, than that of bulk treated specimesn, HV860, in the as-quenched condition or HV760 in the quenched and triple tempered condition. The effects of laser surface heating on hardness and microstructure changes of the tool steel are discussed with the aid of X-Ray diffraction and Mossbauer Effect Spectroscopy (MES) data from selected specimens. Increased surface roughness marked the transition from surface hardening to surface melting.
Striation laser de matériaux métalliques
2005
L'objet du travail présenté est de montrer les conditions de réalisation et d'obtention de stries déterministes calibrées dans un matériau métallique hétérogène (fonte à graphite lamellaire) à l'aide d'un laser YAG. En particulier, seront décrites les stratégies d'usinage associées à la réalisation des profondeurs et des répartitions de stries désirées.
Le Journal de Physique Colloques, 1987
Nous présentons une étude d é t a i l l é e , par microscopie électronique, de l a microstructure d'un alliage Fe-Cr-P-C-Si, refondu superficiellenent par laser. Des échantillons sont prélevés par ultramicrotomie, à diverses profondeurs dans l a zone t r a i t é e . La s t r u c t u r e obtenue l o r s de l a s o l i d i f i c a t i o n rapide e s t complexe e t que partiellement amorphe: une solution t r è s riche en métalloïdes e s t observée entre l e s dendrites; c e t t e solution se présente sous forme de lamelles à l ' i n t é r i e u r desquelles des zones amorphes sont détectées.
Influence d'un traitement laser sur les propriétés d'adhésion de surfaces métalliques
Journal de Physique IV (Proceedings), 2005
Nous avons mis enévidence une nanostructuration de la surface dueà la formation de nanoparticules d'oxydes métalliques dans le plasma et une modification de propriétés chimiques de la surface permettant l'établissement de liaisons acide-base. Les tests mécaniques d'adhérence ont révélé une qualité d'adhésion toutà fait satisfaisante. Le procédé laser apparaît donc comme une technique « propre » de préparation de surface.
2011
Ni47Ti44Nb9 SMA is usually adopted in tightening applications thanks to its large hysteresis. In order to improve understanding its behavior, several experimental tests have been conducted. DSC tests ; SEM observations coupled with chemical analysis. Tensile tests on wires at various temperatures and recovery stress tests on several kinds of samples (rings with circular and rectangular section) were also conducted. A Representative Volume Element (RVE) is also characterised. A thermomechanical model describing the Ni47Ti44Nb9 particular behavior is proposed. Rich-niobium precipitates are considered as ductile inclusions embedded in a NiTi matrix. The macro homogeneous constitutive law depends on matrix’s and inclusions’ constitutive laws and the Mori-Tanaka transition scale technique. The Ni47Ti44Nb9 model is implemented in the ABAQUS. Finally, model was validated by comparisons with recovery stress tests on rings. This validation allows the use of the developed routine as design to...
Effect of multiple laser shock processing on nano-scale microstructure of an aluminum alloy
Characterization and Application of Nanomaterials
In this study, nano-scale microstructural evolution in 6061-T6 alloy after laser shock processing (LSP) was studied. 6061-T6 alloy plate was subjected to multiple LSP. The LSP treated area was characterized by X-ray diffraction and the microstructure of the samples was analyzed by transmission electron microscopy. Focused Ion Beam (FIB) tools were used to prepare TEM samples in precise areas. It was found that even though aluminum had high stacking fault energy, LSP yielded to formation of ultrafine grains and deformation faults such as dislocation cells, stacking faults. The stacking fault probability (PSF) was obtained in LSP-treated alloy using X-Ray diffraction. Deformation induced stacking faults lead to the peak position shifts, broadening and asymmetry of diffraction. XRD analysis and TEM observations revealed significant densities of stacking faults in LSP-treated 6061-T6 alloy. And mechanical properties of LSP-treated alloy were also determined to understand the hardening b...