Non-destructive evaluation of sandwich plates by an ultrasonic IR thermographic method (original) (raw)
Related papers
Ultrasonic and IR Thermographic Detection of a Defect in a Multilayered Composite Plate
Procedia Engineering, 2016
Multi-layered composites are frequently used in many applications as constructional materials. Such materials represent a difficult inspection task for some traditional techniques of non-destructive testing (NDT). Typical defects of composite materials are delaminations, lack of adhesion and crumpling, just to name a few. IR thermography and ultrasonics are typically considered as candidate techniques to detect different types of defects. In order to assess the potential usefulness of both methods, a composite laminate with a polytetrafluoroethylene disk inserted between two layers to simulate a delamination is investigated. Experimental evidences resulting from the two technologies are discussed.
Energies
Ceramic-coated materials used in different engineering sectors are the focus of world-wide interest and have generated a need for inspection techniques that detect very small structural anomalies. Non-destructive testing is increasingly being used to evaluate coating thickness and to test for coating flaws. The main pros of non-destructive testing is that the tested object remains intact and available for continued use afterward. This paper reports on an integrated, non-destructive testing approach that combines infrared thermography and acousto-ultrasonics to evaluate advanced aerospace sandwich structure materials with the aim of exploring any potential for detecting defects of more than one type. Combined, these two techniques successfully detected fabrication defects, including inclusions and material loss.
Thermographic investigation of sandwich structure made of composite material
NDT & E International, 2001
In this paper an experimental procedure, by means of thermographic technique, was set up in order to detect some typical defects, which could be found in composite material sandwich structures. The material thermal response was investigated for different arti®cially defects inserted in some specimens; every kind of defect was listed. Then the experimental procedure was applied to study a wind-turbine blade made of sandwich composite structure. The results ful®lled the expectations and con®rmed the reliability of the thermographic technique to be used both in laboratory and in service. q
Geometrical Limitations to Detection of Defects in Composites by Means of Infrared Thermography
Journal of Nondestructive Evaluation, 2004
The aim of the present experimental study is to gain information about limits in detection of defects in composites by infrared thermography. Specimens are manufactured of either carbon/epoxy, or glass/epoxy, and with inclusions of foreign materials to simulate defects of different size and positioned at different depths. Tests are carried out by using both pulse and lockin techniques. Results are presented in terms of difference of temperature (pulse), or difference of phase angle (lockin), between damaged zones and sound material. It seems that, apart from diameter and depth, the thickness is very crucial for defects visibility.
Composites Part A: Applied Science and Manufacturing, 2015
The damage phenomenon occurring in glass fiber reinforced polymer (GFRP) laminate is very complex; it is inherently an anisotropic, multi-source and multi-scale process. In the present work, a new non destructive testing (NDT) approach is suggested using, simultaneously, multiple techniques. These are bulk and guided ultrasonic waves, acoustic emission, passive and active infrared thermography, for evaluating mechanical damage occurring in GFRP laminate under uniaxial tensile tests. The principal result of this work, other than the success of each applied technique to evaluate the created damage in the material, is the possibility to effectively combine multiple NDT techniques in order to validate or to complete the diagnosis of the structural health of the materials.
IR Thermography Nondestructive Testing Methods of Composite Materials Used in Aerospace Applications
Proceedings of the 2015 Asia International Conference on Quantitative InfraRed Thermography, 2015
In case of composite materials we have to deal with the presence of both high mechanical resistance parameters and low specific gravity. Hence in recent years their use rapidly grows in structures for which these characteristics are of paramount importance. There are mainly aerospace structures. Typical defects of composite materials are: delaminating, lack of adhesion, cracks, concentrations and deformations. These defects can come into being both in manufacturing processes and during exploitation. With the development of technology for producing composite materials the requirements are growing for assessment of their quality. For this purpose nondestructive testing (NDT) is used. NDT procedures using IR thermography can be divided into passive and active. For the diagnosis of defects in composite materials of aerospace applications the active IR thermography methods are used in many cases. The paper presents examples of selected results of defects detection and description of used methods.
Non-destructive Methods for Damage Assessment of Composite Sandwich Structures
MATEC Web of Conferences, 2018
Sandwich structures are capable of absorbing large amounts of energy under impact loads which results in high structural crashworthiness. Comparison of detection capabilities of selected C-scan NDT methods applicable for inspections of sandwich structures was performed using water-squirt, air-coupled and pitch-catch ultrasonic techniques, supplemented by laser shearography. Test results have shown that water-squirt and pitch-catch techniques are the most suitable methods for the core damage evaluation. Air-coupled method showed lower sensitive for detection of some artificial defects and impact damages in honeycomb sandwiches when unfocused transducers were used. The combination of the presented methods was able to reveal most of the defects.
Core-Skin Disbond Detection in a Composite Sandwich Panel Using Guided Ultrasonic Waves
Journal of Nondestructive Evaluation, Diagnostics and Prognostics of Engineering Systems
Advanced composite materials are being increasingly used in state-of-the-art aircraft and aerospace structures due to their many desirable properties. However, such composite materials are highly susceptible to developing internal damage. Thus, safe operation of such structures requires a comprehensive program of effective nondestructive inspection and maintenance of their critical load bearing components before the defects grow and become unstable, resulting in failure of the entire structure. Ultrasonic guided wave-based methods have the potential to significantly improve current inspection techniques for large plate-like structural components due to the waves' large propagation range and sensitivity to defects in their propagation path. The application of guided waves for nondestructive evaluation (NDE) of real structures, however, requires a thorough understanding of the characteristics of guided waves in composite structures in the presence and absence of any defects. In th...
Experimental Mechanics, 2015
An experimental method is proposed for obtaining the fracture toughness of an interfacial crack in sandwich structures. The method relates the interfacial fracture toughness with temperature change developed at the crack front. The focus of the paper is the development of an experimental approach that uses high speed infrared (IR) thermography to capture the temperature evolution during the crack growth. The feasibility of using IR thermography is demonstrated on sandwich structure specimens with E-glass/epoxy face sheets and cross-linked PVC H100 foam core loaded in mixed-mode bending. Different crack propagation paths, in the foam core and at the face sheet/core interface are considered. It is shown that IR thermography with 15 kHz frame rate is able to make a quantitative measurement of the crack front temperature associated with the crack growth. A constant of proportionality ψ is derived between the temperature change per unit area at the crack front and the fracture toughness provided by a validated FE model. It is shown that ψ obtained from specimens with the same crack propagation path is identical, even though the specimen dimensions and loading mode-mixities are different. Thus, it is demonstrated that for a particular interface, once ψ is obtained from a known loading condition, the interfacial fracture toughness from any loading configuration can be determined from a direct temperature measurement.
A study of two Non-destructive Testing methods (NDT) was carried out in specimens with different kinds of simulated defects. Ultrasonics test (US) and Infrared Thermography (IRT) were applied with the aim to evaluate the detectability and the accuracy of each method. These techniques have acquired great importance in the aeronautics industry because they allow to control the aerostructures without intervening in their physical and mechanical integrity. In the second part of the study, a comparison of both techniques was achieved in order to analyse their limits and advantages. It appeared that detectability of defects was much better in a sample with flat-bottomed holes defects in the case of Ultrasonic Test. However it was found that Infrared Thermography is much more limited to the thickness of the specimen than the ultrasonic waves. On the other hand, defects were all revealed with IRT in a sandwich composite including Teflon inserts, which was not the case for US.