Fabrication and Characterization of the Micro-Heater and Temperature Sensor for PolyMUMPs-Based MEMS Gas Sensor (original) (raw)
Related papers
Electro-thermal simulations and modelling of micromachined gas sensor
2001 Microelectromechanical Systems Conference (Cat. No. 01EX521)
Reliability of the membrane structure for micromachined-gas sensors is one of the main concerns in MEMS technology. The major source of this problem is the stress on the membrane. In this study, the use of SiO 2 /Si 3 N 4 /SiO 2 stacked layers with optimized dimensions was found to reduce the stress on the membrane, hence improve the reliability. We have also used electro-thermal simulations with finite element analysis (FEA) to model the structural properties of the membrane in order to reduce the stress. The appropriate selection of materials and dimensions yielded maximum active area temperature of 530°°°°C at the center of the membrane with a polysilicon as a heater element, less than 5V supply voltage, 40mW of power consumption, membrane edge temperature of 177 °°°°C and acceptable mechanical stress of 0.097GPa. Upon realizing the structure with the modeled parameters, micromachined-gas sensors could respond to many industry/environment application demands.
Chemosensors
The design of the heater plays a decisive role in the energy consumption, sensitivity, and speed of chemical sensors. The paper analyzes various options for the topology of meander-type platinum heaters in chemical sensors fabricated on thin dielectric membranes using MEMS-silicon technology. Comprehensive studies of the heater’s current–voltage characteristics have been carried out, heating rates have been measured at various currents, experimental temperature characteristics for various meander topologies have been obtained, heater options have been determined, and optimal heat transfer processes are ensured at a low power consumption of about 20–25 mW. Sensors with an optimal heater topology based on a double dielectric membrane were fabricated according to the described technological process, and sensory responses to 0.5 vol.% CH4 and 0.2% C3H8 were studied. The obtained results showed good results and confirmed the need to choose the optimal heater topology when designing senso...
2009 6th International Conference on Electrical Engineering, Computing Science and Automatic Control (CCE), 2009
A control system to regulate the temperature of the micro hotplate in a MEMS gas sensor is presented. The controlelement, called micro hotplate, is comprised of a micro heater and a temperature sensor, both made with polysilicon, located near each other. This material has a Temperature Coefficient of Resistance (TCR) that is the basis for the design of the temperature controller of the gas sensor system. A high temperature between 250 and 400 °C is needed to produce a chemical reaction between the gas and the sensing film, hence a reliable temperature control for the micro hotplate is desired. Thermal insulation of the circuitry from the heating element, having a monolithic sensor system, and low power consumption, are the main specifications for the system. This is obtained by means of a micro pit realized with MEMS micromachining processes. The analysis of the circuit proposed to fulfill these characteristics is presented, for its future integration with a standard CMOS technology. A trade off is established between the sensor structure parameters and the circuit design.
ACCURATE EXTRACTION OF THE TEMPERATURE OF THE HEATING ELEMENT IN MICROMACHINED GAS SENSORS
The sensitivity and selectivity of micromachined gas sensors strongly depend on the temperature of the heating element; therefore an accurate determination of this temperature is required. In this paper, a simple analytical model of the thermal behavior of a heating element placed onto a thermally insulated dielectric membrane is presented. It is demonstrated that simple resistance vs. power measurements are sufficient for a precise determination of the sensor temperature. These measurements performed "once and for all" at the wafer-level on the statistically relevant number of heaters, allowed us to determine a "universal" temperature vs. power curve.
Thermal model for a microhot plate used in a MEM gas sensor
2008
A thermal analytical model for a MEM gas sensor is presented and compared with an electrical circuit equivalent model. The objective is to study the temperature performance of the microhot plate configured within a MEM structure used for gas sensing. From this, it is possible to determine the magnitude of the electrical current that must be applied to the polysilicon heater on regard of its dimensions and materials used, for instance, when the sensor structure is fabricated with a MEMS technology compatible with CMOS integrated circuits fabrication. Results are presented where the response time and temperature level, as a function of applied current, can be determined. The model presented can be used as a base for designing microhot plates operating in gas sensors, where temperatures in the order of 300 • C are needed and that will be integrated monolithically with associated electronics, with constraints as minimum power dissipation.
Characterization of an Embedded Micro-Heater for Gas Sensors Applications
The heating characteristic of a microheater element, placed onto a thermally insulated dielectric membrane, define the sensitivity and selectivity of a micromachined gas sensor. Therefore an accurate determination of its temperature is required. In this paper, we describe a new four-point probe heating element configuration together with a simple analytical model of its thermal behavior.
MEMS-based microheaters integrated gas sensors
Integrated Ferroelectrics, 2018
In the present work efforts have been made to develop microheater integrated gas sensors with low power consumption. The design and simulation of a single-cell microheater is carried out using ANSYS. Low power consumption (<35 mW) platinum micro-heater has been fabricated using bulk micromachining technique on silicon dioxide membrane (1.5 lm thin), which provided improved thermal isolation of the active area of 250 Â 250 lm 2. The micro-heater has achieved a maximum temperature of 950Catanapplieddcvoltageof2.5V.Fabricatedmircro−heaterhasbeenintegratedwithSnO2basedgassensorsfortheefficientdetectionofH2andNO2gases.Thedevelopedsensorswerefoundtoyieldthemaximumsensingresponseof950 C at an applied dc voltage of 2.5 V. Fabricated mircro-heater has been integrated with SnO 2 based gas sensors for the efficient detection of H 2 and NO 2 gases. The developed sensors were found to yield the maximum sensing response of 950Catanapplieddcvoltageof2.5V.Fabricatedmircro−heaterhasbeenintegratedwithSnO2basedgassensorsfortheefficientdetectionofH2andNO2gases.Thedevelopedsensorswerefoundtoyieldthemaximumsensingresponseof184 and $2.1 with low power consumption of 29.18 and 34.53 mW towards the detection of 1 ppm of NO 2 gas and 500 ppm of H 2 gas, respectively.
Design of the optimum microheater for smart MEMS gas sensor
Conventional Metal Oxide gas sensors commonly used for sensing inflammable hydrocarbon gases and other toxic gases. However, they suffer from the two limitations, viz. (a) their relatively high operating temperature (≥300° c) and (b) large power dissipation (≥1 Watt). Micromachined silicon based metal oxide gas sensors are being developed to overcome these limitations.The main part of power consumption in a micro-machined gas sensor consists of various thermal losses like conduction through bulk silicon substrate, convection in air from all exposed surfaces and radiation. The thermal characteristics of micro-machined metal oxide based gas sensors have to be optimized with respect to low power consumption, well controlled temperature distribution over the sensing layer and fast transient response. However microheater for the MEMS metal oxide gas sensors have not yet been optimized. In this paper we have developed a methodology (software) for designing and optimizing microheater for MEMS based gas sensor. Using this software we can estimate power requirement for achieving a particular temperature as well as the temperature distribution over the active layer.
Thermal and mechanical analysis of micromachined gas sensors
Journal of Micromechanics and Microengineering, 2003
In this paper, we present a complete thermomechanical study of a micromachined gas sensor substrate. The work has been carried out combining coupled electrothermomechanical three-dimensional finite element modelling simulations with electrical, infrared thermography and interferometric microscopy experimental measurements. The performances predicted by simulations, such as the power consumption (heating efficiency in air of 5.7 • C mW −1), the time response (19 ms), the membrane deflection during operation and the preferential failure sites in the micromachined substrate have been confirmed by experience. Their good agreement validates the model, and allows us to consider the adaptability of this design as a micromachined substrate for integrated gas sensors.