Towards the Prediction of Tensile Properties in Automotive Cast Parts Manufactured by LPDC with the A356.2 Alloy (original) (raw)
Related papers
Quantitative assessment of Aluminium cast Alloys` structural parameters to optimize ITS properties
2017
L. Kuchariková, E. Tillová, J. Belan, M. Chalupová, A. Vaško, I. Švecová, University of Žilina, Faculty of Mechanical Engineering, Slovakia The present work deals with evaluation of eutectic Si (its shape, size, and distribution), dendrite cell size and dendrite arm spacing in aluminium cast alloys which were cast into different moulds (sand and metallic). Structural parameters were evaluated using NIS-Elements image analyser software. This software is imaging analysis software for the evaluation, capture, archiving and automated measurement of structural parameters. The control of structural parameters by NIS Elements shows that optimum mechanical properties of aluminium cast alloys strongly depend on the distribution, morphology, size of eute ctic Si and matrix parameters.
Shape/Tiryakioǧlu, 2014
The microstructure and mechanical properties of an automotive component die-cast by Swirled Enthalpy Equilibration Device process are analyzed. Two secondary aluminum alloys have been used, AlSi7Cu3Mg and AlSi9Cu3(Fe) alloys. The castings have been investigated by means of computer tomography to evaluate the concentration and distribution of casting defects, especially in the regions of thick wall thickness. Microstructural investigation has been carried out by means of optical microscope and image analysis technique. The results reveal a not uniform distribution of primary α-Al globules throughout the casting, with a solid fraction ranging from 48 to 58%, and eutectic segregation phenomena. The castings have been mapped in terms of mechanical properties and quality index. The variation of the mechanical properties reflects the presence of local casting defects and alloying segregation.
International Journal of Cast Metals Research, 2018
This paper introduces a new model for prediction of tensile properties of Al A357 castings in the form of UTS (MPa) = a + b ln (G/√Ṫ) and El (%) = c + d ln (G/√Ṫ). While previous models use only SDAS for prediction of tensile properties of the castings, the present model uses G (temperature gradient at solidification front) to evaluate the difficulty of liquid metal feeding and formation of microshrinkages and Ṫ (cooling rate of solidifying alloy) to provide information about SDAS. The proposed model has been developed based on the data from a series of defect free plates and later was applied for prediction of tensile properties of new castings from A357 alloy. It was found that the model successfully predicts the tensile properties of cast Al A357 alloys.
Impact behaviour of A356 alloy for low-pressure die casting automotive wheels
Journal of Materials Processing Technology, 2009
Castings defects Microstructure Numerical simulation a b s t r a c t Instrumented impact strength tests have been carried out on KV sub-size Charpy samples drawn from A356 aluminium alloy 17-in. wheels, produced by a low-pressure die casting. The wheels show different geometry and thermal treatment. In this paper, the effects of microstructure and defects on the impact properties are studied. The results indicate that the impact energy is lower in as-cast wheel than in T6 heat-treated wheels. A finer microstructure always corresponds to higher impact strength, while a direct correlation between the resistance to crack propagation values and secondary dendrite arm spacing (SDAS) exists. Casting defects, revealed by means of X-ray and density measurements techniques, become critical when concentrated around the V-notch, where they reduce the load bearing area of Charpy specimens. The fracture profile and surface of Charpy specimens have been investigated revealing how the crack crosses the interdendritic eutectic region where a significant fraction of cracked eutectic silicon and intermetallic particles is found.
Aluminium and magnesium castings – experimental work and numerical analyses
International Journal of Crashworthiness, 2003
The long-term objective of this work is to develop design and modelling tools that allow the structural behaviour of thin-walled cast components to be predicted when subjected to static and dynamic loads such as in crash situations. The approach consists of the following ingredients: casting of generic geometry relevant for automotive design, component and materials testing, constitutive modelling and validation simulations using the finite element method. Here, HPDC components of both AM60 and AlSi7Mg have been subjected to axial crushing and 3-point bending. An existing elastoplastic constitutive equation has been calibrated and evaluated based on material tests. Next, validation analyses of the generic structural components subjected to static loading were performed. The thin-walled cast components are modelled in the explicit FE-code LS-DYNA using shell elements. So far, it has been found that an elastoplastic material model based on the isotropic yield criterion of von Mises reasonably well captures the behaviour of HPDC components subject to both axial loading and 3-point bending. In addition, the ultimate loads in the different load cases are over-predicted analytically with the use of Eurocode 9 (EC9). Figure 1 Instrument panel structure of GM van cast by Meridian Technologies Inc.
The influence of casting process on quality and performances on Al based automotive components
Aluminium alloys are more and more increasing their importance in different industries, in particular, in the automotive field, where castings represent extremely interesting solutions especially for those applications in which the necessity of high mechanical properties is combined with the need of a substantial weight saving. In this work, investigations on fatigue and microstructural characteristics were done on specimens drawn directly from production components, samples dimensions were the maximum allowed by component dimensions. The influence of different casting processes are here compared.
Materials Science and Engineering: A, 2006
The aim of the present study was to investigate the influence of solidification thermal variables on the as-cast microstructure of hypoeutectic Al-Si alloys and to establish correlations with the casting mechanical properties. Experimental results include transient metal/mold heat transfer coefficients, tip growth rate, local solidification time, secondary dendrite arm spacing, ultimate tensile strength and yield strength as a function of solidification conditions imposed by the metal/mold system. It was found that the ultimate tensile strength increases with increasing alloy solute content and with decreasing secondary dendrite arm spacing. Yield strength seems to be independent of both alloy composition and dendritic arrangement. Such results have permitted general expressions correlating dendrite spacing with transient solidification processing variables to be established. The correlation of such expressions with experimental equations relating the ultimate tensile strength and dendrite spacing provides an insight in the preprogramming of solidification in terms of mechanical strength of Al-Si castings. Predictive theoretical and experimental approaches for dendritic growth have been compared with the present experimental observations.
Progress in Ductile Aluminium High Pressure Die Casting Alloys for the Automotive Industry
2007
Today the die casting process is used to cast parts with high quality requirements such as engine cradles, cross members and nodes for space frame construction. This has presented the challenge to design alloys with superior mechanical properties. For crash relevant parts requiring high ductility (elongation > 12 %) one option to meet these properties is by heat treating a low iron Al-Si alloy to a T4 or T7 temper. However heat treatment can lead to part distortion and blistering resulting in higher costs for the producer. The second option is Al-Mg alloys type which fulfill these requirements in the as-cast state but the alloys are not easy to cast. Research was started using the easy to cast Al-Si alloy system targeting a high elongation (> 12 %) and yield-strength (> 120 MPa) already in temper F and not showing any long term aging behavior. This paper will discuss the technical progress which began in the early 1990ies, gaining in importance with the first series space f...
Materials & Design, 2009
Many studies have demonstrated a relationship between secondary dendrite arm spacing (SDAS) and the mechanical behaviour of cast aluminium-silicon alloys, both for tensile and fatigue strength. SDAS is related to the solidification time and can be predicted, with a good approximation, by finite-element simulation. However, other microstructural features can affect the tensile behaviour of cast aluminium alloys such as size and morphology of the eutectic Si particles, grain size, composition and morphology of the intermetallic compounds. The present investigation was aimed at finding valuable relationships between ultimate tensile strength and the previously mentioned microstructural parameters for the sand cast A357 aluminium alloy. The microstructural characterization was carried out by optical microscopy and image analysis on more than about 2500 micrographs. Starting from the microstructural parameters and taking into account the material hardness, a relationship able to predict the ultimate tensile strength of the alloy, with an error less than 5%, was found. This relationship can be used to evaluate the local values of the UTS in complex cast components knowing only the hardness and the microstructural parameters, even in positions where the extraction of tensile specimens is not possible.