Metallurgical characterization of natural aging effects on pre-deformed Al 7075/T651 alloy during retrogression and re-aging heat treatment (original) (raw)
Related papers
High-Temperature Deformation of Naturally Aged 7010 Aluminum Alloy
2021
This study is focused on the deformation mechanism and behavior of naturally aged 7010 aluminum alloy at elevated temperatures. The specimens were naturally aged for 60 days to reach a saturated hardness state. High-temperature tensile tests for the naturally aged sample were conducted at different temperatures of 573, 623, 673, and 723 K at various strain rates ranging from 5 × 10−5 to 10−2 s−1. The dependency of stress on the strain rate showed a stress exponent, n, of ~6.5 for the low two temperatures and ~4.5 for the high two temperatures. The apparent activation energies of 290 and 165 kJ/mol are observed at the low, and high-temperature range, respectively. These values of activation energies are greater than those of solute/solvent self-diffusion. The stress exponents, n, and activation energy observed are rather high and this indicates the presence of threshold stress. This behavior occurred as a result of the dislocation interaction with the second phase particles that are ...
METALLOFIZIKA I NOVEISHIE TEKHNOLOGII, 2019
In this study, the effect of the aging time on microstructure and mechanical properties of the AA7075 alloy after T6 heat treatment is investigated. The AA7075 alloys are quenched after solid solution treatment at 485°C for 2 hours and artificially aged at 120°C using five different aging times. Hardness measurements, microstructure examinations (SEM + EDS, XRD), and tensile tests are performed for the aged alloys. Fractured surfaces are also examined using SEM images after the tensile testing. The results of the studies conducted show that the hardness value of the alloys can be increased by increasing aging time, and the maximum hardness value of 192 HV is obtained for the alloy aged for 25 hours. Tensile tests also show that the tensile strength of the alloy can be increased by increasing aging time, and the maximum tensile strength value of 580 MPa is obtained for the alloy aged for 25 hours. Fractured surface examinations revealed that the ductile fracture mechanism is mostly dominant, while the planar fracture mechanism is observed as well.
Effect of T6 and Re-Aging Heat Treatment on Mechanical Properties of 7055 Aluminum Alloy
World Academy of Science, Engineering and Technology, International Journal of Chemical, Molecular, Nuclear, Materials and Metallurgical Engineering, 2015
Heat treatable aluminum alloys such as 7075 and 7055, because of high strength and low density, are used widely in aircraft industry. For best mechanical properties, T6 heat treatment has recommended for this regards, but this temper treatment is sensitive to corrosion induced and Stress Corrosion Cracking (SCC) damage. For improving this property, the over-aging treatment (T7) applies to this alloy, but it decreases the mechanical properties up to 30 percent. Hence, to increase the mechanical properties, without any remarkable decrease in SCC resistant, Retrogression and Re-Aging (RRA) heat treatment is used. This treatment performs in a relatively short time. In this paper, the RRA heat treatment was applied to 7055 aluminum alloy and then effect of RRA time on the mechanical properties of 7055 has been investigated. The results show that the 40-minute time is suitable time for retrogression of 7055 aluminum alloy and ultimate strength increases up to 625MPa. Keywords—7055 Aluminu...
Materials Science and Engineering: A
The results of detailed microstructural analyses of the commercial aluminum alloy 7075 in several tempers, combined with consideration of similar data on pure Al-Zn-Mg alloys, are shown to provide a sound basis for the interpretation of various calorimetric studies reported in the literature. Particular emphasis is placed on the analysis of differential scanning calorimetry (DSC) data on the peak-aged microstructure of both types of alloy, and of the effect of retrogression and reaging (RRA) treatments on the aluminum alloy 7075. It is demonstrated that all the salient features of the DSC curves can be rationalized with the precipitate microstructures produced by the various heat treatments, specifically rl' precipitates in the peak-aged alloys and mixtures of rf and r 1 precipitates in the slightly overaged and RRA alloys.
Microstructural characterization of interrupted aging on an AA7050 aluminum alloy
Materials Characterization, 2019
Interrupted aging heat treatments are used to maximize the gain in mechanical properties in 7xxx aluminum alloys through the production of a microstructure with a high density of fine precipitates, which are homogeneously dispersed in the aluminum matrix. In an interrupted aging heat treatment, the first stage, at higher temperature, aims at creating sites for subsequent nucleation of precipitate particles, while the second stage, at lower temperature, aims at the nucleation and growth of precipitate particles. The Interrupted aging heat treatment has been increasingly studied because it confers resistance levels similar to, or even higher than conventional heat treatments (e.g T6), in addition to producing a more stable microstructure. In this study, a microstructural characterization was carried out using differential scanning calorimetry (DSC), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD) in an AA7050 aluminum alloys that was submitted to aging heat treatments T7451, T6 and T6I4-65, seeking a better understanding of the microstructure produced in each heat treatment and the reasons of the gain in mechanical properties. The results indicated that the T6I4-65 interrupted aging heat treatment was the most efficient in creating sites for nucleation of phases in the aluminum matrix, when compared with other conditions, due to the higher density of particles of the phases η',η and T, in addition to being the only condition to have GPII zones and S phase in its microstructure.
Transactions of Nonferrous Metals Society of China, 2014
Structural features, aging behavior, precipitation kinetics and mechanical properties of a 6013 Al-Mg-Si aluminum alloy subjected to equal channel angular pressing (ECAP) at different temperatures were comparatively investigated with that in conventional static aging by quantitative X-ray diffraction (XRD) measurements, differential scanning calorimetry (DSC) and tensile tests. Average grain sizes measured by XRD are in the range of 66−112 nm while the average dislocation density is in the range of 1.20×10 14 −1.70×10 14 m −2 in the deformed alloy. The DSC analysis reveals that the precipitation kinetics in the deformed alloy is much faster as compared with the peak-aged sample due to the smaller grains and higher dislocation density developed after ECAP. Both the yield strength (YS) and ultimate tensile strength (UTS) are dramatically increased in all the ECAP samples as compared with the undeformed counterparts. The maximum strength appears in the samples ECAP treated at room temperature and the maximum YS is about 1.6 times that of the statically peak-aged sample. The very high strength in the ECAP alloy is suggested to be related to the grain size strengthening and dislocation strengthening, as well as the precipitation strengthening contributing from the dynamic precipitation during ECAP.
Influence of aging parameters on the mechanical properties of 6063 aluminium alloy
Journal of Materials Processing Technology, 2000
The 6063 aluminium alloy were given various heat treatments at under-aged, peak-aged and over-aged temperatures. The effect of precipitation on the tensile strength, yield strength, hardness, ductility and number of cycles required to fail the alloy at constant stress was investigated. The variation in time and temperature have improved the mechanical properties of the Al-alloy, whereas the ductility has decreased. The experimental work has revealed that time and temperature play a very important role in the precipitation hardening process of the Al-alloy. The initial increase in the tensile strength, yield strength, hardness and fatigue is due to vacancies assisted diffusion mechanism and formation of high volume fraction of guinier preston (GP) zones, which disturbs the regularity in the lattices. In over-aging of the alloy, the size of the individual particle increases, but the number of particles decreases. This causes few obstacles to the movement of dislocations, therefore, the mechanical properties decreases. The scanning electron microscope (SEM) study of the under-aged alloy have exhibited facet fatigue fracture surface, whereas the peak-aged and over-aged alloy show a mixed mode of fracture, i.e. facet fracture with striation and also intergranular fracture.
Influence of Plastic Deformation on the Properties of 6066 Heat Treatable Aluminum Alloys
Walailak Journal of Science and Technology (WJST), 2013
The aims of this work are to (1) study the influence of plastic deformation on the properties of 6066 aluminum alloy; (2) study the effect of deformation on the age hardening of these alloys; (3) study the recovery of these defects from the samples. These effects were investigated in terms of microstructure using positron annihilation spectroscopy (PAS) analysis and mechanical properties by hardness measurements. Dislocations facilitate nucleation of precipitates. At first sight, deformed specimens had lower hardness as compared to non-deformed ones, and as the deformation increase, the hardness decreases. Another output of the mechanical test was the increase in hardness in the specimens after artificial aging with an increase in percent deformation.
Effect of Artificial Aging Temperature on Mechanical Properties of 6061 Aluminum Alloy
January 2019
Aluminum alloys have been attracted by several engineering sectors due to their excellent strengthweight ratio and corrosion resistant properties. These are categorized into 1, 2, 3, 4, 5, 6, 7and 8xxx on the basis of alloying elements. Among these 6xxx series contains aluminum–magnesium–silicon as alloying elements and are widely used in extruded products and automotive body panels. The major advantages of these alloys are good corrosion resistance, medium strength, low cost, age hardening response no yield point phenomenon and Ludering. 6xxx series alloys generally have lower formability than other aluminum alloys which restrict their utilization for wide applications. Keeping in view of the shortcomings in the set of mechanical properties of 6xxx series the efforts were made to improve the tensile strength and toughness properties through age hardening. In present study heat treatment cycles were studied for 6061 aluminum alloy. Three different age hardening temperatures 160, 200...
The Effect of Ageing Temperature in T6 Heat Treatment on Mechanical Properties of AA7075
Acta Physica Polonica A, 2019
In this study, the effect of ageing temperatures in T6 heat treatment on the microstructural changing and mechanical properties of AA7075 were investigated. The samples were quenched after solution treatment at 485 • C for 2 h. The natural ageing was applied for 1 h, and then artificial ageing was carried out at five different temperatures (100-140 • C) for 24 h. Hardness measurements, microstructure, X-ray diffraction examinations, and tensile tests of aged samples were carried out. As a result of the study, the hardness values and ultimate tensile stress values were increased by increasing ageing temperatures up to 120 • C. Then it was decreased by increasing ageing temperature. Ultimate tensile stress values were compatible with hardness values and maximum ultimate tensile stress values were obtained in aged samples at 120 • C.