Extremely Sensitive Microwave Microfluidic Dielectric Sensor Using a Transmission Line Loaded with Shunt LC Resonators (original) (raw)
Related papers
Ultrahigh-Sensitivity Microwave Sensor for Microfluidic Complex Permittivity Measurement
IEEE Transactions on Microwave Theory and Techniques, 2019
The conventional resonant-type microwave microfluidic sensors made of planar resonators suffer from limited sensitivities. This is due to the existence of several distributed capacitors in their structure, where just one of them acts as a sensing element. This article proposes a very high-sensitivity microwave sensor made of a microstrip transmission line loaded with a shunt-connected series LC resonator. A large sensitivity for dielectric loadings is achieved by incorporating just one capacitor in the resonator structure. Applying sample liquids to the microfluidic channel implemented in the capacitive gap area of the sensor modifies the capacitor value. This is translated to a resonance frequency shift from which the liquid sample is characterized. The sensor performance and working principle are described through a circuit model analysis. Finally, a device prototype is fabricated, and experimental measurements using water/ethanol solutions are presented for verification of the sensing principle. Index Terms-Dielectric measurement, microfluidic sensor, microwave sensor, planar resonators.
Integrated microwave resonant device for dielectric analysis of microfluidic systems
Journal of Physics: Conference Series, 2011
Herein we present a device for performing non-contact dielectric spectroscopy upon liquids in a microfluidic environment. The device is comprised of a compression-sealed polytetrafluoroethylene (PTFE) chip with an embedded coaxial resonator, which is overmoded for dielectric measurements at six discrete frequencies between 1 and 8 GHz. A novel capacitive coupling structure allows transmission measurements to be taken from one end of the resonator, and an optimised microchannel design maximises sensitivity and repeatability. The use of a PTFE substrate and a non-contact measurement gives excellent chemical and biological compatibility. A simple 'fingerprint' method for identifying solvents is demonstrated, whereby a sample is characterised by air-referenced changes in complex frequency. Complex permittivity values are also obtained via a perturbation theory-based inversion. A combination of experimental and simulated results is used to characterise the device behaviour, limits of operation and measurement uncertainty. The high stability of temporal measurements, coupled with the robustness of the design, make this device ideal for analytical chemistry and industrial process control.
Al-Furat Journal of Innovations in Electronics and Computer Engineering, 2020
a microwave microfluidic microstrip spilt ring resonator is presented in this paper for liquid sensing and characterization. The sensor is designed to operate at frequency of 1.4 GHz and quality factor of 360. The sensor has been tested with several solvents to verify its sensitivity where the resonant frequency and losses vary with each solvent. The shift in the resonant frequency and the change in the insertion loss have been used to extract the values of the complex permittivity of the solvent. The measured complex permittivities of the solvents have been compared with the theoretical values with very good agreement. This sensor can be utilized in many industrial and medical application where the characterization of liquids are needed.
High Sensitive Microwave Micro-Fluidic Sensor Using Split Ring Resonator
2020
Microwave resonators are commonly used as precise instruments for the measurements of dielectric and electromagnetic properties of materials such as the complex permeability and complex permittivity and surface resistance at microwave frequencies. Many medical and pharmaceutical applications, food industries, and chemical applications require accuracy in calculating complex permittivity of sample under test. In this work, the design and fabrication of high sensitive microwave microfluidic sensors are based on a split ring resonator for liquid permittivity characterization. A microwave microfluidic microstrip SRR is presented in this thesis for liquid sensing and characterization. The 3-D simulations of the sensor are implemented using COMSOL Multiphysics 5.4 to reach a good agreement between simulated and experimental results. The sensor is designed to operate at a frequency of 1.4 GHz and a quality factor of 360. The sensor has been tested with several solvents (water, ethanol, and chloroform) to verify its sensitivity where the resonant frequency and quality factor vary with each solvent. The shift in the resonant frequency and the change in the losses have been used to get the values of the complex permittivity of the solvents. The measured complex permittivity of the solvents has been compared with the theoretical values as there was a very good compatibility between them. Furthermore, we present a new approach for microfluidic sensing using an active split ring resonator (ASRR). ASRR with high sensitivity is presented for measure characterization of liquid with a very small liquid volume approximately 0.4 nL operations at L band. The 3-D simulations of the ASRR are implemented using Advanced Design System 2016.01 (ADS). RF amplifier LNA assists a passive planer microwave sensor inside an aluminum cylindrical cavity to be active SRR. This study consists of two parts; the first part is a calculation of the quality factor and losses of some common fluids (water,ethanol, chloroform, and petroleum ether) using both passive and active SRR to increase Q- factor from 250 to 814 with reducing the loss from 19.6 dB to 6.6 dB when passive SRR is loaded with an empty tube due to RF amplifier generate negative resistance and compensating energy and loss in the passive sensor. As the resolution of the sensor increases with the increase in the quality factor. The second part, via using an active SRR, sensing the high concentrations of sodium sulfite (1 - 3.17) M at 25°C and thus sensor can be used to measure salt concentrations in water. Microstrip stopband split ring resonator (SSRR) for microwave microfluidic is presented for measuring complex permittivity of liquid with different positions of microfluidic channel that operates at resonant frequency of 1 GHz. The sensor was fabricated and microfluidic channel is located in the gap groove with two different positions of the carrier where the electric field is as large as possible. The sensor has been tested with several solvents to verify its sensitivity where the electric field interacts with the liquid filled in a quartz tube and hence alter the SRR behavior. The electromagnetic properties (complex permittivity) of the solutions can be extracted from the change in the resonant frequency of the resonator due to the perturbation phenomenon.
High-Sensitivity Metamaterial-Inspired Sensor for Microfluidic Dielectric Characterization
IEEE Sensors Journal, 2000
A new metamaterial-inspired microwave microfluidic sensor is proposed in this paper. The main part of the device is a microstrip coupled complementary split-ring resonator (CSRR). At resonance, a strong electric field will be established along the sides of CSRR producing a very sensitive area to a change in the nearby dielectric material. A micro-channel is positioned over this area for microfluidic sensing. The liquid sample flowing inside the channel modifies the resonance frequency and peak attenuation of the CSRR resonance. The dielectric properties of the liquid sample can be estimated by establishing an empirical relation between the resonance characteristics and the sample complex permittivity. The designed microfluidic sensor requires a very small amount of sample for testing since the cross-sectional area of the sensing channel is over five orders of magnitude smaller than the square of the wavelength. The proposed microfluidic sensing concept is compatible with lab-on-a-chip platforms owing to its compactness.
Microwave Sensor within a Microfluidic Chip for Biological Applications
Proceedings, 2017
A miniaturized sensor operating in Radio Frequency region (RF) is proposed to address the need in picoliter liquid characterization. The sensor is based on a coplanar waveguide (CPW) combined with a microfluidic channel dedicated to microliter liquid characterization with perspectives for biology and single cell characterization. Using microtechnology process, the sensor has been designed on a 0.5 mm thick quartz wafer with Cr/Au electrodes. A prototype of the sensor has been fabricated and evaluated with ethanol/water mixtures at different molar fractions of ethanol. A good agreement between theoretical and measured electrical response of the sensor is observed.
Design of miniaturized highly sensitive liquid sensor at microwave frequency
International Journal of RF and Microwave Computer-Aided Engineering, 2020
In this paper, we have presented a simple, miniaturized, and highly sensitive liquid sensor, which determines the dielectric properties of liquids at microwave frequency. In the proposed design, the concept of interdigital capacitor (IDC) is employed to construct the sensor. The proposed IDC based sensor responds differently depending on the liquids' dielectric property. The proposed structure utilizes the shift in resonance frequency and peak attenuation as the sensing parameter to determine the complex dielectric permittivity of the unknown liquids. The advantage of the proposed sensor structure lies in its compactness (0.08λ 0 × 0.08λ 0 × 0.003λ 0) and high sensitivity, 0.42%. The designed sensor can also be used in the biomedical field for noninvasive bioliquid characterization.
Microwave frequency sensor for detection of biological cells in microfluidic channels
Biomicrofluidics, 2009
We present details of an apparatus for capacitive detection of biomaterials in microfluidic channels operating at microwave frequencies where dielectric effects due to interfacial polarization are minimal. A circuit model is presented, which can be used to adapt this detection system for use in other microfluidic applications and to identify ones where it would not be suitable. The detection system is based on a microwave coupled transmission line resonator integrated into an interferometer. At 1.5 GHz the system is capable of detecting changes in capacitance of 650 zF with a 50 Hz bandwidth. This system is well suited to the detection of biomaterials in a variety of suspending fluids, including phosphate-buffered saline. Applications involving both model particles ͑polystyrene microspheres͒ and living cells-baker's yeast ͑Saccharomyces cerevisiae͒ and Chinese hamster ovary cells-are presented.
Sensors, 2021
In this paper, we describe a low-cost microwave microfluidic system of ultrahigh sensitivity for detecting small changes in the concentration of polar solutions (liquid dielectrics) in the 2.4 GHz ISM band. Its principle of operation is based on microwave interferometry, which is implemented using planar microstrip lines and integrated microwave components. The key features of this system include small solution intake (<200 µL per measurement), short time of measurement (ca. 20 ms), ultrahigh sensitivity of concentration changes (up to 55 dB/%), and low error of measurement (below 0.1%). The ultrahigh sensitivity was proven experimentally by measurements of the fat content of milk. In addition, it is a user-friendly system due to an effortless and fast calibration procedure. Moreover, it can be made relatively compact (<20 cm2) and features low power consumption (200 mW). Thus, the proposed system is perfect for industrial applications, especially for highly integrated lab-on-...