Effect of CNTs dispersion on the thermal and mechanical properties of Cu/CNTs nanocomposites (original) (raw)
Related papers
Carbon nanotubes (CNTs) with its exceptional thermal and mechanical properties hold the promise of delivering high performance nanocomposite materials. To utilize CNTs as effective reinforcement in metal nanocomposites, appropriate dispersion and robust interfacial adhesion between individual CNT and metal matrix have to be certain. This work presents a novel combined technique of nanoscale dispersion (NSD) of functionalized multiwalled carbon nanotubes (MWCNTs) in copper (Cu) matrix composite followed by powder injection molding (PIM). MWCNTs contents were varied from 0 to 10 volume fraction. Evidences on the existence of functional groups and microstructural analysis of the fabricated nanocomposites were determined using TEM, EDX, FESEM and FTIR. Thermal conductivity and elasticity measurements were also performed. The results showed that the impurities of the pristine MWCNTs such as Fe, Ni catalyst, and the amorphous carbon have been significantly removed after sonication process. FESEM and TEM observations showed high stability of MWCNTs at elevated temperatures and uniform dispersion of MWCNTs in Cu matrix at different volume fractions and sintering temperatures (950, 1000 and 1050 C). The experimentally measured thermal conductivities of Cu/MWCNTs nanocomposites showed remarkable increase (11.25% higher than pure sintered Cu) with addition of 1 vol.% MWCNTs, while the modulus of elasticity (Young’s modulus) of Cu/MWCNTs nanocomposites sintered at 1050 C for 2 h was increased proportionally to the increment in MWCNTs contents.
Experimental Preparation and Numerical Simulation of High Thermal Conductive Cu/CNTs Nanocomposites
Due to the rapid growth of high performance electronics devices accompanied by overheating problem, heat dissipater nanocomposites material having ultra-high thermal conductivity and low coefficient of thermal expansion was proposed. In this work, a nanocomposite material made of copper (Cu) reinforced by multi-walled carbon nanotubes (CNTs) up to 10 vol. % was prepared and their thermal behaviour was measured experimentally and evaluated using numerical simulation. In order to numerically predict the thermal behaviour of Cu/CNTs composites, three different prediction methods were performed. The results showed that rules of mixture method records the highest thermal conductivity for all predicted composites. In contrast, the prediction model which takes into account the influence of the interface thermal resistance between CNTs and copper particles, has shown the lowest thermal conductivity which considered as the closest results to the experimental measurement. The experimentally measured thermal conductivities showed remarkable increase after adding 5 vol.% CNTs and higher than the thermal conductivities predicted via Nan models, indicating that the improved fabrication technique of powder injection molding that has been used to produced Cu/CNTs nanocomposites has overcome the challenges assumed in the mathematical models.
International Journal of Manufacturing Engineering, 2013
This work presents a novel fabrication approach of multiwalled carbon nanotubes (MWNTs) reinforced copper (Cu) matrix nanocomposites. A combination of nanoscale dispersion of functionalized MWNTs in low viscose media of dissolved paraffin wax under sonication treatment followed by metal injection molding (MIM) technique was adopted. MWNTs contents were varied from 0 to 10 vol.%. Information about the degree of purification and functionalization processes, evidences on the existence of the functional groups, effect of sonication time on the treated MWNTs, and microstructural analysis of the fabricated Cu/MWNTs nanocomposites were determined using TEM, EDX, FESEM, and Raman spectroscopy analysis. The results showed that the impurities of the pristine MWNTs such as Fe, Ni catalyst, and the amorphous carbon have been significantly removed after purification process. Meanwhile, FESEM and TEM observations showed high stability of MWNTs at elevated temperatures and uniform dispersion of MWNTs in Cu matrix at different volume fractions and sintering temperatures (950, 1000 & 1050 ∘ C). The experimentally measured thermal conductivities of Cu/MWNTs nanocomposites showed remarkable increase (11.25% higher than sintered pure Cu) with addition of 1 vol.% MWNTs, and slight decrease below the value of sintered Cu at 5 and 10 vol.% MWNTs.
Advances in Natural Sciences: Nanoscience and Nanotechnology, 2011
Metal matrix nanocomposites have become popular in industrial applications. Carbon nanotubes (CNTs), since theirs appearance, with their unique properties such as exceptionally small diameters and high Young's modulus, tensile strength and high chemical stability, are considered to be an attractive reinforcement material for lightweight and high-strength metallic matrix composites. The powder metallurgy method allows nanocomposite materials, notably metal-ceramic composites, to be produced by sintering a mixture of powders.
Microstructures and tensile behavior of carbon nanotube reinforced Cu matrix nanocomposites
Materials Science and Engineering: A, 2006
Carbon nanotubes (CNTs) have been considered as an ideal reinforcement to improve the mechanical performance of monolithic materials. However, the CNT/metal nanocomposites have shown lower strength than expected. In this study, the CNT reinforced Cu matrix nanocomposites were fabricated by spark plasma sintering (SPS) of high energy ball-milled nano-sized Cu powders with multi-wall CNTs, and followed by cold rolling process. The microstructure of CNT/Cu nanocomposites consists of two regions including CNT/Cu composite region, where most CNTs are distributed, and CNT free Cu matrix region. The stress-strain curves of CNT/Cu nanocomposites show a two-step yielding behavior, which is caused from the microstructural characteristics consisting of two regions and the load transfer between these regions. The CNT/Cu nanocomposites show a tensile strength of 281 MPa, which is approximately 1.6 times higher than that of monolithic Cu. It is confirmed that the key issue to enhance the strength of CNT/metal nanocomposite is homogeneous distribution of CNTs.
2013
Uniform dispersion of carbon nanotubes (CNTs) in metal composites has been by far the most significant challenge in the field of CNT-reinforced metal matrices. This work presents a new dispersion and fabrication technique of Carbon nanotubes (CNTs) reinforced copper (Cu) matrix nanocomposites. A combination of nanoscale dispersion of functionalized CNTs in low viscose media of dissolved paraffin wax under ultrasonication treatment followed by powder injection molding (PIM) technique was adopted. CNTs contents were varied from 0 to 10 vol.%. TEM, EDX, FESEM and Raman spectroscopy analysis were used for materials characterization. Information about the degree of purification and functionalization processes, evidences on the existence of the functional groups, effects of ultrasonication time on the treated CNTs, and microstructural analysis of the fabricated Cu/CNTs nanocomposites were determined. The results showed that the impurities of the pristine CNTs such as Fe, Ni catalyst and the amorphous carbon have been significantly removed after purification process. Meanwhile, FESEM and TEM observations showed high stability of CNTs at elevated temperatures. It also showed an excellent homogeneous dispersion of CNTs in Cu matrix and led to a strong interfacial bonding between Cu particles and individual CNTs.
Carbon nanotubes (CNTs) reinforced copper (Cu) matrix nanocomposites prepared via advanced fabrication method is presented. Functionalization and ultrasonication processes have been applied to enhance the dispersion of purified CNTs and creates sidewalls groups that have the potential to bond CNTs to the metal matrix. The main part of this approach was metal injection molding (MIM) technique, which is a combination of powder metallurgy and plastic injection molding technique. Preparation of MIM feedstock required a melting and mixing process of binder system (polymers) with the solid loading, which has been carried out using a twin screw rotor machine. This machine provides a viscous media of the molten binder with high shear forces that allow the additives (carbon nanotubes/copper powder) to be mixed properly and exfoliate the CNTs clusters with uniformdispersion inside the Cu matrix. Subsequently, to prove our expected results, observation tests of TEM, SEM, FESEM and CNTS were employed and discussed literally.
The effect of sintering temperature on Cu-CNTs nano composites properties produced by PM method
Science of Sintering
In this research work, copper and CNTs have been processed using high energy milling in different milling times (5, 10 and 15 hours). FESEM and XRD have been used to characterize the milled powders. The FESEM micrographs of the milled powders indicated that the morphology of powders changed from spherical shape to flake as milling time increased. The effect of sintering temperature as well as CNTs content on the properties of Cu-CNTs nanocomposite has been investigated. The optimum sintering temperature to produce Cu-CNTs nanocomposites is determined to be 900 oC. The microstructure and phase analysis of Cu-CNTs nanocomposites were studied by field emission scanning electron microscopy and X-ray diffraction. Mechanical properties of nanocomposite samples at various sintering temperatures were investigated. Cu-CNTs nanocomposite with 4 vol.% CNTs fabricated by powder metallurgy method indicated the highest value of the micro-hardness and bending strength as compared to pure copper.
Advanced Powder Technology, 2018
Copper (Cu) gained its importance in several applications due to its attractive thermal characteristics. However, its applications are limited, wherever high strength and high thermal conductivity are desirable. Thus, an attempt was made to develop Cu/CNT composites having the improved mechanical and thermal properties. Initially, Cu/CNT composite powder was synthesized through molecular level mixing technique, where the functionalized 20-40 nm and 40-60 nm diameter CNT with varying concentrations from 0.25 to 1.0 wt.% with an increment of 0.25 wt.% were used. The powder was uniaxially compacted at 800 MPa and sintered in the range of 2-8 hr at 900°C. The best characteristics of Cu/CNT composites obtained from the present study are as follows: Relative density (RD)-89.1%, Hardness-61.2 ± 0.58 VHN, Thermal conductivity-343 W/mK and these characteristics obtained their maximum value at 0.25 wt.% CNT concentration and started to decrease irrespective of CNT diameter.