Characterization and workplace exposure assessment of nanomaterial released from a carbon nanotube-enabled anti-corrosive coating (original) (raw)
Related papers
Characterization of Exposure to Carbon Nanotubes in an Industrial Setting
The Annals of occupational hygiene, 2014
While production and use of carbon nanotubes (CNTs) is increasing, workers exposure to CNTs is expected to increase as well, with inhalation being potentially the main pathway for uptake. However, there have been few studies reporting results about workers' personal exposure to CNTs. In this study, worker exposure to single-walled CNTs (SWCNTs) during the production of conductive films in a modern up-scaling factory was assessed. Particulate matter concentrations (2.5-10 μm) and concentrations of CO and CO2 were monitored by using real-time instruments. Workers' exposure levels to SWCNTs were qualitatively estimated by analyzing particle samples by transmission electron microscopy (TEM). TEM samples identified high aspect ratio (length/width > 500) SWCNTs in workplace air. SWCNT concentrations estimated from micrographs varied during normal operation, reactor use without local exhaust ventilation (LEV), and cleaning between 1.7×10(-3), 5.6 and 6.0×10(-3) SWCNT cm(-3), res...
Annals of Work Exposures and Health
To date there is no consensus about the most appropriate analytical method for measuring carbon nanotubes (CNTs), hampering the assessment and limiting the comparison of data. The goal of this study is to develop an approach for the assessment of the level and nature of inhalable multi-wall CNTs (MWCNTs) in an actual workplace setting by optimizing and evaluating existing analytical methods. In a company commercially producing MWCNTs, personal breathing zone samples were collected for the inhalable size fraction with IOM samplers; which were analyzed with carbon analysis, inductively coupled plasma mass spectrometry (ICP-MS) and scanning electron microscopy/ energy dispersive X-ray spectroscopy (SEM/EDX). Analytical methods were optimized for carbon analysis and SEM/EDX. More specifically, methods were applied and evaluated for background correction using carbon analyses and SEM/EDX, CNT structure count with SEM/EDX and subsequent mass conversion based on both carbon analyses and SEM/EDX. A moderate-to-high concordance correlation coefficient (R C) between carbon analyses and SEM/EDX was observed [R C = 0.81, 95% confidence interval (CI): 0.59-0.92] with an absolute mean difference of 59 µg m −3. A low R C between carbon analyses and ICP-MS (R C = 0.41, 95% CI: 0.07-0.67) with an absolute mean difference of 570 µg m −3 was observed. The large absolute difference between EC and metals is due to the presence of non-embedded inhalable catalyst particles, as a result of which MWCNT concentrations were over-This article contains public sector information licensed under the Open Government Licence v3.0(http://www.nationalarchives.gov.uk/doc/ open-government-licence/version/3/).
Exposure assessment of carbon nanotube manufacturing workplaces
Inhalation Toxicology, 2010
Seven CNT (carbon nanotube) handling workplaces were investigated for exposure assessment. Personal sampling, area sampling, and real-time monitoring using an SMPS (scanning mobility particle sizer), dust monitor, and aethalometer were performed to characterize the mass exposure, particle size distribution, and particle number exposure. No workplace was found to exceed the current ACGIH (American Conference of Governmental Industrial Hygienists) TLVs (threshold limit values) and OELs (occupational exposure levels) set by the Korean Ministry of Labor for carbon black (3.5 mg/m 3), PNOS (particles not otherwise specified; 3 mg/m 3), and asbestos (0.1 fiber/cc). Nanoparticles and fine particles were most frequently released after opening the CVD (chemical vapor deposition) cover, followed by catalyst preparation. Other work processes that prompted nanoparticle release included spraying, CNT preparation, ultrasonic dispersion, wafer heating, and opening the water bath cover. All these operation processes could be effectively controlled with the implementation of exposure mitigation, such as engineering control, except at one workplace where only natural ventilation was used.
Carbon nanotube dosimetry: from workplace exposure assessment to inhalation toxicology
Particle and Fibre Toxicology
Dosimetry for toxicology studies involving carbon nanotubes (CNT) is challenging because of a lack of detailed occupational exposure assessments. Therefore, exposure assessment findings, measuring the mass concentration of elemental carbon from personal breathing zone (PBZ) samples, from 8 U.S.-based multi-walled CNT (MWCNT) manufacturers and users were extrapolated to results of an inhalation study in mice. Upon analysis, an inhalable elemental carbon mass concentration arithmetic mean of 10.6 mug/m3 (geometric mean 4.21 mug/m3) was found among workers exposed to MWCNT. The concentration equates to a deposited dose of approximately 4.07 mug/d in a human, equivalent to 2 ng/d in the mouse. For MWCNT inhalation, mice were exposed for 19 d with daily depositions of 1970 ng (equivalent to 1000 d of a human exposure; cumulative 76 yr), 197 ng (100 d; 7.6 yr), and 19.7 ng (10 d; 0.76 yr) and harvested at 0, 3, 28, and 84 d post-exposure to assess pulmonary toxicity. The high dose showed ...
Inhalation Toxicity of Multiwall Carbon Nanotubes in Rats Exposed for 3 Months
Toxicological Sciences, 2009
Carbon nanotubes (CNT) are of great commercial interest. Theoretically, during processing and handling of CNT and in abrasion processes on composites containing CNT, inhalable CNT particles might be set free. For hazard assessment, we performed a 90-day inhalation toxicity study with a multiwall CNT (MWCNT) material (Nanocyl NC 7000) according to Organisation for Economic Co-operation and Development test guideline 413. Wistar rats were head-nose exposed for 6 h/day, 5 days/week, 13 weeks, total 65 exposures, to MWCNT concentrations of 0 (control), 0.1, 0.5, or 2.5 mg/m 3 . Highly respirable dust aerosols were produced with a proprietary brush generator which neither damaged the tube structure nor increased reactive oxygen species on the surface. Inhalation exposure to MWCNT produced no systemic toxicity. However, increased lung weights, pronounced multifocal granulomatous inflammation, diffuse histiocytic and neutrophilic inflammation, and intra-alveolar lipoproteinosis were observed in lung and lung-associated lymph nodes at 0.5 and 2.5 mg/m 3 . These effects were accompanied by slight blood neutrophilia at 2.5 mg/m 3 . Incidence and severity of the effects were concentration related. At 0.1 mg/m 3 , there was still minimal granulomatous inflammation in the lung and in lung-associated lymph nodes; a no observed effect concentration was therefore not established in this study. The test substance has low dust-forming potential, as demonstrated by dustiness measurements, but nonetheless strict industrial hygiene measures must be taken during handling and processing. Toxicity and dustiness data such as these can be used to compare different MWCNT materials and to select the material with the lowest risk potential for a given application.
Annals of Occupational Hygiene, 2015
Background: The industrial use of novel manufactured nanomaterials such as carbon nanotubes and carbon nanodiscs is increasing globally. Occupational exposure can occur during production, downstream use, and disposal. The health effects of many nanomaterials are not yet fully characterised and to handle nano-objects, their aggregates and agglomerates > 100 nm (NOAA), a high degree of control measures and personal protective equipment are required. The emission of airborne NOAA during production and handling can contaminate workplace surfaces with dust, which can be resuspended resulting in secondary inhalation exposures and dermal exposures. This study surveys the presence of carbon-based nanomaterials, such as multi-walled carbon nanotubes (MWCNTs) and carbon nanodiscs, as surface contamination at a small-scale producer using a novel tape sampling method. Methods: Eighteen different surfaces at a small-scale producer were sampled with an adhesive tape sampling method. The surfaces selected were associated with the production and handling of MWCNT powder in the near-field zone. Surfaces in the far-field zone were also sampled. In addition, tape stripping of the skin was performed on one worker. The tape samples were analysed with scanning electron microscopy to detect the carbon-based NOAA. Air sampling with a personal impactor was also performed on a worker who was producing MWCNTs the same day as the tape samples were collected. Results: MWCNTs were detected in 50% of the collected tape samples and carbon nanodiscs in 16%. MWCNTs and carbon nanodiscs were identified in all parts of the workplace, thus, increasing the risk for secondary inhalation and dermal exposure of the workers. Both airborne MWCNTs and carbon nanodiscs were detected in the personal impactor samples. The tape-strip samples from the worker showed no presence of carbon-containing nanoparticles. 3 Conclusions: Tape sampling is a functional method for detecting surface contamination of carbon-based NOAA and for exposure control during production at potentially any workplace that produces or handles such manufactured nanomaterials. With the tape method it is possible to monitor if a potential for secondary inhalation exposure or dermal exposure exists through resuspension of dust deposited on workplace surfaces. By means of air sampling we could confirm that carbon nanodiscs were resuspended into the air at the workplace even though they were not handled during that particular work shift. MWCNTs were detected in the air samples, but can have been derived from either resuspension or from the work tasks with MWCNTs that were performed during the air sampling. Tape sampling is a complementary method to air sampling and together these two methods provide a better view of the hygienic situation in workplaces where NOAA can be emitted into work environments.
Critical Reviews in Toxicology, 2006
Nanotechnology has emerged at the forefront of science research and technology development. Carbon nanotubes (CNTs) are major building blocks of this new technology. They possess unique electrical, mechanical, and thermal properties, with potential wide applications in the electronics, computer, aerospace, and other industries. CNTs exist in two forms, single-wall (SWCNTs) and multi-wall (MWCNTs). They are manufactured predominately by electrical arc discharge, laser ablation and chemical vapor deposition processes; these processes involve thermally stripping carbon atoms off from carbon-bearing compounds. SWCNT formation requires catalytic metals. There has been a great concern that if CNTs, which are very light, enter the working environment as suspended particulate matter (PM) of respirable sizes, they could pose an occupational inhalation exposure hazard. Very recently, MWCNTs and other carbonaceous nanoparticles in fine (<2.5 µm) PM aggregates have been found in combustion streams of methane, propane, and natural-gas flames of typical stoves; indoor and outdoor fine PM samples were reported to contain significant fractions of MWCNTs. Here we review several rodent studies in which test dusts were administered intratracheally or intrapharyngeally to assess the pulmonary toxicity of manufactured CNTs, and a few in vitro studies to assess biomarkers of toxicity released in CNT-treated skin cell cultures. The results of the rodent studies collectively showed that regardless of the process by which CNTs were synthesized and the types and amounts of metals they contained, CNTs were capable of producing inflammation, epithelioid granulomas (microscopic nodules), fibrosis, and biochemical/toxicological changes in the lungs. Comparative toxicity studies in which mice were given equal weights of test materials showed that SWCNTs were more toxic than quartz, which is considered a serious occupational health hazard if it is chronically inhaled; ultrafine carbon black was shown to produce minimal lung responses. The differences in opinions of the investigators about the potential hazards of exposures to CNTs are discussed here. Presented here are also the possible mechanisms of CNT pathogenesis in the lung and the impact of residual metals and other impurities on the toxicological manifestations. The toxicological hazard assessment of potential human exposures to airborne CNTs and occupational exposure limits for these novel compounds are discussed 189 190 C.-W. LAM ET AL. in detail. Environmental fine PM is known to form mainly from combustion of fuels, and has been reported to be a major contributor to the induction of cardiopulmonary diseases by pollutants. Given that manufactured SWCNTs and MWCNTs were found to elicit pathological changes in the lungs, and SWCNTs (administered to the lungs of mice) were further shown to produce respiratory function impairments, retard bacterial clearance after bacterial inoculation, damage the mitochondrial DNA in aorta, increase the percent of aortic plaque, and induce atherosclerotic lesions in the brachiocephalic artery of the heart, it is speculated that exposure to combustion-generated MWCNTs in fine PM may play a significant role in air pollution-related cardiopulmonary diseases. Therefore, CNTs from manufactured and combustion sources in the environment could have adverse effects on human health.
Toxicological …, 2006
Carbon nanotubes (CNT) are an important new class of technological materials that have numerous novel and useful properties. The forecast increase in manufacture makes it likely that increasing human exposure will occur, and as a result, CNT are beginning to come under toxicological scrutiny. This review seeks to set out the toxicological paradigms applicable to the toxicity of inhaled CNT, building on the toxicological database on nanoparticles (NP) and fibers. Relevant workplace regulation regarding exposure is also considered in the light of our knowledge of CNT. CNT could have features of both NP and conventional fibers, and so the current paradigm for fiber toxicology, which is based on mineral fibers and synthetic vitreous fibers, is discussed. The NP toxicology paradigm is also discussed in relation to CNT. The available peer-reviewed literature suggests that CNT may have unusual toxicity properties. In particular, CNT seem to have a special ability to stimulate mesenchymal cell growth and to cause granuloma formation and fibrogenesis. In several studies, CNT have more adverse effects than the same mass of NP carbon and quartz, the latter a commonly used benchmark of particle toxicity. There is, however, no definitive inhalation study available that would avoid the potential for artifactual effects due to large mats and aggregates forming during instillation exposure procedures. Studies also show that CNT may exhibit some of their effects through oxidative stress and inflammation. CNT represent a group of particles that are growing in production and use, and therefore, research into their toxicology and safe use is warranted.
Nanotechnologies in Russia, 2015
Nanoscale size and fiber like structure of carbon nanotubes (CNTs) may determine high reactivity and penetration, as well as the pathogenicity of asbestos and other mineral fibers. Despite many in vitro and in vivo studies, the absence of full-scale data on CNT effects on human health clearly point out the necessity for epidemiological studies. Currently, several projects are initiated worldwide on studying health risks associated with the inhalation of industrial CNTs, including NIOSH-promoted research (United States), the European CANTES study, and the Russian CNT-ERA project. Studies comprising several successive steps, such as CNT exposure assessment in occupational settings, toxicological evaluation, and epidemiological observations, are critical for determining material safety and use criteria.
Current Environmental Health Reports, 2021
Purpose of review:The purpose of this review is to consolidate exposure assessment methods for occupational research on engineered nanomaterials (ENMs) published within the past five years (2015–2020).Recent findings:The three ENMs that generated the highest volume of new research include titanium dioxide, graphene, and aluminum oxide. A multi-metric approach, using both online and offline instruments and analyses has been found to be a useful method to characterize ENM workplace exposures and was commonly used in the recently published literature. Particle number concentration was the most common online exposure metric used, followed by the metrics of mass and surface area. There are currently no consensus methods for offline analyses of most ENMs. Researchers generally used gravimetric or elemental analyses for carbonaceous nanomaterials, titanium dioxide, and other nanometals, but there was little overlap between other ENM materials reviewed. Using biological markers of exposure, such as urinary oxidative stress biomarkers, as an indication of chronic exposure may also be useful for some ENMs and should be further researched.Summary:Generally, similar online instrumentation and offline electron microscopy methods were used for all ENMs. However, this consistency was not observed for offline mass analysis methods within specific ENMs. Consolidation of the most recent methods and results of exposure assessments within this broad material category can guide researchers towards future areas of study. Establishing consensus methods of exposure assessment for each individual ENM is crucial to characterizing workplace exposures, pooling data to fully understand their associated risks, and developing useful occupational exposure limits.