Approach of Dynamic Modelling of a Hydraulic System (original) (raw)
Related papers
Applied Sciences
Energy storage is essential if net zero emissions are to be achieved. In fact, energy storage is a leading solution for reducing curtailment in an energy system that relies heavily on intermittent renewables. This paper presents a comparison between two numerical models which simulate the energy conversion unit performance of a hydro-pneumatic energy storage system. Numerical modelling is performed in PythonTM (Alpha Model) and Mathworks® Simulink® and SimscapeTM (Beta Model). The modelling aims to compare the time-series predictions for the simplified model (Alpha Model) with the more physically representative model (Beta Model). The Alpha Model provides a quasi-steady-state solution, while the Beta Model accounts for machinery inertias and friction within hydraulic flow circuits. Results show that the energy conversion performance simulations between the two models compare well, with a notable difference during system start-up due to the inclusion of transients in the Beta Model. ...
Modeling of Hydro-Pneumatic Energy Storage Using Pump Turbines
2011
Modelling of a hydro-pneumatic energy storage system is the main aim of this paper. The project aims to model a prototype that uses a rotodynamic multi-stage pump-turbine to displace a virtual liquid piston for air compression. A dynamic model of the storage system is developed using the block diagram methodology. Two driving strategies are also developed in order to manage the constant variation of operating point due to pressure variation: maximum efficiency strategy and power demand response strategy.
Development And Evaluation Of A Simplified Modeling Approach For Hydraulic Systems
2012
This paper presents how a hydraulic system can be properly modeled for hydraulic balancing, knowledge of flow distribution, coupled simulation, and evaluation of control, etc. It focuses on water-based heating and cooling systems, which generally have high energy efficiency in design but could perform poorly in reality due to the undersensing condition and strong thermal-hydraulic coupling. The study introduces the motivation, presents the simplified modeling methodology, and illustrates the model and simulating structure. A preliminary evaluation of the method is conducted with two simple simulations. The proposed "node-branch-state" modeling approach could be easily modified, expanded and integrated into a detailed thermal model. The paper concludes with some discussions on future work.
Modeling and control of a novel compressed air energy storage system for offshore wind turbine
A novel compressed air energy storage system for wind turbine is proposed. It captures excess power prior to electricity generation so that electrical components can be downsized for demand instead of supply. Energy is stored in a high pressure dual chamber liquid-compressed air storage vessel. It takes advantage of the power density of hydraulics and the energy density of pneumatics in the "open accumulator" architecture. A liquid piston air compressor/expander is utilized to achieve near-isothermal compression/expansion for efficient operation. A dynamic system model as well as control laws for optimizing the turbine power, delivering required electrical power and maintaining system pressure are developed. A set of simulation case studies demonstrate the operation of the system.
MODELING AND SIMULATION OF HYDRAULIC-ENERGY SAVING SYSTEM: AN OVERVIEW
Based on the systematic of the well-known closed circuit mobile transmissions, a new hydrostatic transmission system, to be applied in power hydraulics, is introduced in this paper. There are multiple ways of conserving the energy of a vehicle to improve efficiency. The use of flywheel technology or hydraulic accumulator or both, an effective means of conserving energy in hybrid vehicles. This paper presents the introduction, mathematical modeling and review of the engineering and mechanics of the flywheel, and will clarify how flywheel and hydraulic accumulator energy storage work and how they can be applied to hybrid vehicles.
Modelling and experimental studies on hydro-pneumatic energy storage using pump-turbines
2013
Studies on a hydro-pneumatic energy storage system are the main goal of this paper. Firstly a functional modelling of a closed cycle storage structure (Figure 1) is introduced. The paper first introduces the model based on the dynamic behaviour of the mechanical, hydraulic and thermodynamic domains. The key points of the system are introduced: 1the analysis of the accumulation efficiency led us to favour an isothermal cycle in the future; 2power rate management optimization requires the study of alternative storage structures. To finish, a comparison between a storage/recovery cycle measurements and modelling results shows that observations were quite correctly predicted.
Analysis and Optimization of a Compressed Air Energy Storage Systems in Aquifer
American Society of Mechanical Engineers (Paper), 1986
This paper discusses the thermo-economic analysis and optimization of a constant pressure Compressed Air Energy Storage system, in aquifer, subjected to an exogenous periodic electricity price function of the interconnection. The target function considered is the net benefit of the plant. It is related to the fundamental planning parameters of the system like the compressor pressure ratio, the maximum temperature ratio, the charging-discharging duration ratio and the plant capacity factor. The results of the analysis permit to obtain the optimal values of the fundamental parameters to be used in the planning process. NOMENCLATURE c-constant pressure specific heat, P h ch-charging duration, (hr/yr),
Energy, 2011
Energy storage systems are becoming more important for load leveling, especially because of the widespread use of intermittent renewable energy. Compressed air energy storage (CAES) is a very promising method for energy storage because CAES relies on existing technologies, is less expensive, and easier to site and permit, as compared to pumped hydro storage. But, in the case of CAES employing hard rock caverns or man-made air vessels, although the smallest possible cavern volume is desirable in order to minimize the construction cost and optimize utilization of the given space, the operating pressure range in the cavern must be limited in order to reduce the deterioration in efficiency of the CAES system at off-design conditions. In this paper, a new constant-pressure CAES system combined with pumped hydro storage was studied to address the current problem associated with the conventional CAES systems. An energy and exergy analysis of the novel CAES system was performed in order to understand the operation characteristics of the system according to several different compression and expansion processes; we then examined the effects of the height of the storage cavern and heat transfer between two media (air, water) and the cavern on the performance of the novel CAES system.
Analysis and Optimization of a Compressed Air Energy Storage System in Aquifer
1986
This paper discusses the thermo-economic analysis and optimization of a constant pressure Compressed Air Energy Storage system, in aquifer, subjected to an exogenous periodic electricity price function of the interconnection. The target function considered is the net benefit of the plant. It is related to the fundamental planning parameters of the system like the compressor pressure ratio, the maximum temperature ratio, the charging-discharging duration ratio and the plant capacity factor. The results of the analysis permit to obtain the optimal values of the fundamental parameters to be used in the planning process. NOMENCLATURE c-constant pressure specific heat, P h ch-charging duration, (hr/yr),
Transient-Flow Induced Compressed Air Energy Storage (TI-CAES) System towards New Energy Concept
Water, 2020
In recent years, interest has increased in new renewable energy solutions for climate change mitigation and increasing the efficiency and sustainability of water systems. Hydropower still has the biggest share due to its compatibility, reliability and flexibility. This study presents one such technology recently examined at Instituto Superior Técnico based on a transient-flow induced compressed air energy storage (TI-CAES) system, which takes advantage of a compressed air vessel (CAV). The CAV can produce extra required pressure head, by compressing air, to be used for either hydropower generation using a water turbine in a gravity system or to be exploited in a pumping system. The results show a controlled behaviour of the system in storing the pressure surge as compressed air inside a vessel. Considerable power values are achieved as well, while the input work is practically neglected. Higher power values are attained for bigger air volumes. The TI-CAES offers an efficient and fle...