Stone Age - African Tools, Artifacts, Culture | Britannica (original) (raw)

News •

Paleolithic

The Paleolithic of Africa is characterized by a variety of stone-tool assemblages, some of which represent purely local developments while others are practically identical with materials from corresponding horizons in Europe. Geological investigations of the Late Cenozoic deposits of this continent indicate that, as the result of fluctuations in rainfall, the Pleistocene Epoch throughout most of Africa can be subdivided on the basis of a succession of pluvial and interpluvial stages. The pluvials, known as Kageran, Kamasian, Kanjeran, and Gamblian, are believed to represent the tropical and subtropical equivalents of the four major glacial stages of the Northern Hemisphere. The archaeological succession is well established in certain areas, although not in the continent as a whole.

North Africa

In this area, pebble tools have been reported from one site in Algeria in direct association with a Lower Pleistocene (Villafranchian) mammalian assemblage. Throughout Tunisia, Algeria, Morocco, and the Sahara region, Lower Paleolithic hand axes of both Abbevillian and Acheulean type, together with flake tools, have been found in great numbers. The geological evidence shows that the Sahara region was far less arid during Pleistocene times than it is at present. The Middle Paleolithic of both Levalloisian and Mousterian facies is very widespread in North Africa, and it apparently persisted as late as the second maximum of the Würm glaciation in terms of the European sequence. A specialized Middle Paleolithic development, known as the Aterian, occurred there; it is characterized by tanged points made on flakes and flake blades. This was succeeded by two distinctive blade-tool complexes—the Capsian and Oranian—which are more or less contemporary. Their main development took place during the time span of the European Mesolithic. The Capsian sites are all inland, whereas the Oranian has a coastal distribution. Both are microlithic tool complexes that persisted after the introduction of Neolithic traits into the area.

Egypt

The Pleistocene terrace gravels of the Nile Valley in Egypt have produced a wealth of Paleolithic materials. The 30-meter (98-foot) terrace contains typical Abbevillian and early Acheulean hand axes, including a special form with a triangular section known as the Chalossian type. These are associated with early flake implements. In the 15-meter (49-foot) terrace, developed Acheulean has been recorded, while the nine-meter (29.5-foot) terrace yields large flakes and cores of Levalloisian type. In the low terrace, which occurs at a height of three meters (10 feet) above river level, developed Levalloisian (originally called Mousterian) has been reported. Overlying the low terrace, a local development known as the Sebilian is found. It contains very highly evolved flake implements of Levallois type and, in its later phases, a definite microlithic industry. Of approximately the same age as the Sebilian are several Epi-Levalloisian sites in the Lower Nile drainage, including the Fayyūm Depression and the al-Khārijah (Kharga) Oasis. In the latter area, where the specialized Levalloisian development is called the Khargan, an Egyptian version of the Aterian has been discovered.

East Africa

In Kenya, the oldest known tools—consisting of early hammers, anvils, and cutting tools—date to the Middle Pliocene Epoch and predate the emergence of the oldest confirmed specimens of Homo by almost one million years. The tools were discovered in a dry riverbed near Kenya’s Lake Turkana.

See a researcher making an Oldowan flint flake from obsidian through a technique known as knappingA researcher shapes obsidian through a technique known as knapping, which was used during the Stone Age to make sharp-edged tools.

See all videos for this article

Also in Kenya, Tanzania, and Uganda, types of pebble tools, roughly chipped to an edge on one side only, occur in deposits of Lower Pleistocene age. This development, known as the Kafuan, apparently evolved into an industry characterized by implements made on pebbles chipped to an edge on both sides, called the Oldowan. Overlying the latter are beds containing true Lower Paleolithic hand axes of Abbevillian and Acheulean type, together with flake tools. Associated with the Middle and Late Acheulean are cleavers made on flakes, as well as evidence of the use of the prepared striking-platform–tortoise-core (Levallois) technique in the production of flakes. In the next-younger horizon, two distinct toolmaking traditions are found: the Kenya Stillbay, a Levalloisian derivative characterized by small- to medium-sized, bifacially flaked points or minute hand axes; and the Kenya Fauresmith, basically of Acheulean inspiration and very similar to the true Fauresmith of Southern Africa. Carefully shaped round stone balls, believed to have been used as bola weights in hunting, constitute part of the Fauresmith assemblage. In the post-Gamblian dry phase, microlithic tools appear for the first time in an assemblage known as the Magosian. This was followed by the introduction into the area of a true blade technique, called the Kenya Capsian, together with the art of pottery making. More or less contemporary with the localities where the earliest pottery is found in East Africa, a series of sites has been discovered yielding typical microlithic assemblages and referable to the Kenya Wilton, also found in South Africa, Zimbabwe, and Zambia.