bandwidth (original) (raw)

Author: the photonics expert (RP)

Definition: the width of some frequency or wavelength range

More specific terms: gain bandwidth, resonator bandwidth, modal bandwidth, phase-matching bandwidth

Categories: light detection and characterization, physical foundations

Units: Hz, nm

Formula symbol: <$\Delta \nu$>, <$\Delta \lambda$>

DOI: 10.61835/g6b Cite the article: BibTex plain textHTML Link to this page LinkedIn

In photonics, the term bandwidth occurs in many different cases. The following sections discuss some important cases.

Bandwidth in Terms of Optical Frequency

In the following cases, bandwidth means the width of a range of optical frequencies:

• A light source can have some optical bandwidth (or linewidth), meaning the width of the optical spectrum of the output. For narrow-linewidth lasers, the bandwidth can be extremely small – in extreme cases below 1 Hz, which is many orders of magnitude less than the mean optical frequency. On the other hand, ultrashort pulses with few-femtosecond pulse durations can have very large bandwidth – easily tens of terahertz.
• An optical bandwidth can be the width of a frequency range which can somehow be handled by an optical element or photonic device. For example, it can be the reflection bandwidth of a mirror, the optical transmission bandwidth of an optical fiber, the gain bandwidth of an optical amplifier, or the phase-matching bandwidth of a nonlinear optical device.

A common definition of spectral width is the full width at half maximum (FWHM), but other definitions are also used. For example some authors use the half width at half maximum (HWHM), which is just half the FWHM.

Figure 1: The optical spectrum of an unchirped 80-fs ultrashort light pulse. Its full width at half maximum bandwidth is 8.9 nm, corresponding to 3.9 THz.

Optical bandwidth values may be specified in terms of frequency or wavelength. Due to the inverse relationship of frequency and wavelength, the conversion factor between gigahertz and nanometers depends on the center wavelength or frequency. For converting a (small) wavelength interval into a frequency interval, the equation \Delta \nu = \frac{c}{{{\lambda ^2}}}\Delta \lambda

can be used. (It can be obtained by considering the derivative of <$\nu = c / \lambda$> with respect to <$\lambda$>.) This shows that 1 nm is worth more gigahertz if the center wavelength is shorter.

The optical bandwidth of a light source is strongly related to the temporal coherence, characterized with the coherence time.

Both for passive resonators (e.g. optical cavities) and for the output of oscillators (e.g. lasers), the Q factor is the oscillation frequency divided by the bandwidth.

Ultrashort pulses of light intrinsically have a significant optical bandwidth, even if their instantaneous optical frequency is close to constant [1].

Bandwidth of Modulations

A bandwidth can also indicate the maximum frequency with which a light source can be modulated, or at which modulated light can be detected with a photodetector.

In the area of optical fiber communications, the term bandwidth is also often inaccurately used for the data rate (e.g. in units of Gbit/s) achieved in an optical communication system. A more appropriate term would be data rate or data transmission capacity, avoiding any confusion with optical bandwidth.

Note that the data transmission capacity has only a limited relation to the optical bandwidth. Although a large data transmission rate is not possible without a large optical bandwidth, different communications devices can differ substantially in terms of spectral efficiency, i.e., concerning what data rate is achievable per megahertz of optical bandwidth.

Bandwidth of Photodetectors

A photodetector has a limited bandwidth, here meaning the frequency range in which modulations of the optical power can be detected. Typically, that frequency range would start from zero frequency, but in some cases (AC-coupled photodetectors) that is not the case. In the common case of DC-coupled photodetectors, the bandwidth is equated to the maximum detectable modulation frequency according to some criterion. Frequently, one specifies a 3-dB-bandwidth, meaning the frequency where the signal power (proportional to the square of the output voltage or current) is reduced by 3 decibels. That quantity is related to the rise and fall time. If those times are equal, they may be estimated to be 0.35 divided by the 3-dB bandwidth.

Note that when modulation frequencies reach the bandwidth limits, one does not only experience a reduction of responsivity, but also phase changes. That can be problematic, for example, in the context of feedback loops.

More to Learn

Encyclopedia articles:

• optical spectrum
• time–bandwidth product
• gain bandwidth
• coherence time
• transform limit

Blog articles:

• The Photonics Spotlight 2007-10-11: “Understanding Fourier Spectra”

Bibliography

(Suggest additional literature!)

Suppliers

Questions and Comments from Users

Here you can submit questions and comments. As far as they get accepted by the author, they will appear above this paragraph together with the author’s answer. The author will decide on acceptance based on certain criteria. Essentially, the issue must be of sufficiently broad interest.

Please do not enter personal data here. (See also our privacy declaration.) If you wish to receive personal feedback or consultancy from the author, please contact him, e.g. via e-mail.

By submitting the information, you give your consent to the potential publication of your inputs on our website according to our rules. (If you later retract your consent, we will delete those inputs.) As your inputs are first reviewed by the author, they may be published with some delay.