laser rods (original) (raw)

Author: the photonics expert (RP)

Definition: laser crystals (or glasses) in the form of (usually cylindrical) rods

Categories: article belongs to category optical materials optical materials, article belongs to category laser devices and laser physics laser devices and laser physics

Related: laser crystalsrod lasersdoping concentration

Page views in 12 months: 537

DOI: 10.61835/53m Cite the article: BibTex BibLaTex plain textHTML Link to this page! LinkedIn

Content quality and neutrality are maintained according to our editorial policy.

Contents

What are Laser Rods?

Laser crystals are used with various geometric shapes. One of the common shapes is that of a rod. Most frequently, this means a crystal where the length is substantially longer than the diameter — often several centimeters or even a few tens of centimeters –, and the cross-section is cylindrical. Such long laser rods are required for lamp-pumped lasers; their length is similar to that of the arc lamps or flash lamps. Much shorter rods (normally with a length of only a few millimeters) are used in diode-pumped lasers.

Lasers containing one or more laser rods are called rod lasers.

See the article on laser crystals for more details.

Features of Laser Rods

Dimensions

Rod dimensions can vary substantially between different applications, but should generally be met with good accuracy, since problems with accurate mounting may otherwise result.

Often, relevant parameters are only the length and diameter (for cylindrical rods with flat end surfaces perpendicular to the axis). In addition, one may have slightly tilted outer faces with a specified tilt angle, and ideally indications on the crystals concerning the orientation. Some rods have one or two slightly curved endfaces, but flat ends are more common.

Materials

Most laser rods consist of a crystalline host medium (e.g. YAG = yttrium aluminum garnet) which is doped with some laser-active rare-earth ion such as Nd3+ (neodymium), Yb3+ (ytterbium) or Er3+ (erbium). However, there are also transition-metal-doped rods, e.g. with Ti3+ doping. Also, the host medium is sometimes not monocrystalline, but polycrystalline with a fine grain structure (→ ceramic laser gain media) or a glass.

For long rods, the choice of materials is somewhat more limited than for short ones. For example, it is hard to make large YVO4 (vanadate) crystals, which are therefore normally available only with quite small sizes. Also, long Ti:sapphire rods can be made but are not common, since one could hardly apply the required high pumping intensity with that format.

An important parameter is the doping concentration, i.e., the concentration of laser-active ions. Higher doping can improve the pump absorption efficiency and/or allow the use of a shorter or thinner rod, but may also favor parasitic processes such as energy transfers which degrade the power conversion efficiency.

Unfortunately, specifications for the doping concentration are not always precisely met. (They could be checked with absorption spectroscopy.) Another potential problem is that the doping may not be perfectly homogeneous (particularly for rods with high doping concentrations). That can lead to variations not only of the laser gain, but also of the refractive index, which leads to beam distortions. A high optical homogeneity is usually desirable, particularly when high laser beam quality is required.

Although in most cases nominally homogeneous doping is used, there are laser rods with an intentionally introduced doping gradient, and composite laser crystals obtained by bonding of different materials, e.g. Nd-doped and undoped YAG.

While usually one uses only one type of laser-active ions and no other optically relevant dopant, there are also co-doped rods, typically for exploiting some useful energy transfer processes. Some examples:

The laser-active dopants often absorb visible light in certain wavelength ranges, and that causes a color appearance, which is well visible at least for large (thick) rods. For example, neodymium-doped rods appear pink, and erbium-doped rods can have a similar color.

Surface Finish and Coatings

High-quality surface finish (with precise orientation, high flatness, good scratch/dig specifications) is generally required for the two endfaces, through which the laser beam is usually sent. The optical quality of the outer surface (mantle) is usually much less critical, although it often serves for the entry of pump light (for side-pumped lasers). That surface is also used for cooling.

The endfaces are usually equipped with anti-reflection coatings for the relevant laser [wavelength|wavelength(s)] to minimize power losses and interference effects. In some cases, reflecting coatings are applied to laser rods.

The quality of the interface polish and the coatings can have a substantial impact on the threshold intensity (or fluence) for laser-induced damage. That damage threshold is relevant for pulsed lasers, particularly those with high peak power.

Frequently Asked Questions

This FAQ section was generated with AI based on the article content and has been reviewed by the article’s author (RP).

What is a laser rod?

A laser rod is a common form of laser crystal, typically a cylinder with a length substantially greater than its diameter. Lasers built using these components are known as rod lasers.

What materials are laser rods typically made of?

Most laser rods consist of a crystalline host like YAG doped with laser-active rare-earth ions (e.g., Nd3+, Yb3+). Other host materials include glass and polycrystalline ceramics.

How does the pump source affect the size of a laser rod?

The pump source has a significant impact on rod dimensions. Lamp-pumped lasers require long rods, often several centimeters in length, whereas diode-pumped lasers typically use much shorter rods of only a few millimeters.

Why is a high-quality surface finish important for laser rods?

A high-quality finish on the end faces is crucial for applying effective anti-reflection coatings to minimize power loss. It also increases the threshold for laser-induced damage, which is particularly important for high-power pulsed lasers.

What are the consequences of non-uniform doping in a laser rod?

Non-uniform doping can cause spatial variations in both the laser gain and the refractive index. These inhomogeneities can lead to significant distortions of the laser beam, degrading the beam quality.

What are composite laser rods?

Composite rods are made by bonding different materials together. A common example is bonding a doped section (e.g., Nd:YAG) to an undoped section of the same host crystal.

Questions and Comments from Users

Here you can submit questions and comments. As far as they get accepted by the author, they will appear above this paragraph together with the author’s answer. The author will decide on acceptance based on certain criteria. Essentially, the issue must be of sufficiently broad interest.

Please do not enter personal data here. (See also our privacy declaration.) If you wish to receive personal feedback or consultancy from the author, please contact him, e.g. via e-mail.

By submitting the information, you give your consent to the potential publication of your inputs on our website according to our rules. (If you later retract your consent, we will delete those inputs.) As your inputs are first reviewed by the author, they may be published with some delay.