Marco Chiesa - Academia.edu (original) (raw)

Papers by Marco Chiesa

Research paper thumbnail of Light intensity, temperature, and thickness dependence of the open-circuit voltage in solid-state dye-sensitized solar cells

Physical Review B, 2006

We present an analytical and experimental investigation into the origin of the open-circuit volta... more We present an analytical and experimental investigation into the origin of the open-circuit voltage in the solid-state dye-sensitized solar cell. Through Kelvin probe microscopy, we demonstrate that a macroscopically uniform electric field exists throughout the nanocomposite between the electrodes. Considering a balance between drift and diffusion currents, and between charge generation and recombination, we develop an analytical expression for the open-circuit voltage which accurately follows experimental data. We find the open-circuit voltage increases with light intensity as 1.7kT/q , where T is absolute temperature, however it decreases with increasing temperature and device thickness. The intensity dependence arises from the charge generation rate increasing more strongly with intensity than the recombination rate constant, resulting in increased chemical potential within the device. We find that the temperature dependence arises from a reduction in the charge lifetime and not from increased charge diffusion and mobility. The thickness dependence is found to derive from two factors; first, charge recombination sites are distributed throughout the film, enabling more charges to recombine in thicker films before influencing the potential at the electrodes, and second, the average optical power density within the film reduces with increasing film thickness.

Research paper thumbnail of High stability X-ray spectroscopy system with on-chip front-end in charge amplifier configuration

Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment, 2003

Research paper thumbnail of Correlation between Surface Photovoltage and Blend Morphology in Polyfluorene-Based Photodiodes

Nano Letters, 2005

We present a microscopic study of photoinduced charge generation in polyfluorene-based photovolta... more We present a microscopic study of photoinduced charge generation in polyfluorene-based photovoltaic structures. The sub-100 nm lateral resolution of scanning Kelvin probe microscopy allows characterizing the three-dimensional structure of thin films of blends of poly-(9,9'-dioctylfluorene-co-benzothiadiazole) (F8BT) and poly-(9,9'-dioctylfluorene-co-bis-N,N'-(4-butylphenyl)-bis-N,N'-phenyl-1,4-phenylenediamine) (PFB). From the strong correlation between surface photovoltage and blend morphology, we propose a simple model for the lateral and vertical film structure identifying in particular those regions with the most efficient conduction pathway for the photocurrent.

Research paper thumbnail of Photovoltaic Performance and Morphology of Polyfluorene Blends:  The Influence of Phase Separation Evolution

Research paper thumbnail of Ultrastructural evaluation of enamel surface morphology after tooth bleaching followed by the application of protective pastes

Scanning, 2016

The aim of the present in vitro study was to evaluate the morphology of bleached enamel surface f... more The aim of the present in vitro study was to evaluate the morphology of bleached enamel surface followed by the application of different protective pastes. Specimens were prepared from 50 human incisors free of caries and defects. The bleaching procedure was performed with 35% hydrogen peroxide (Perfect Bleach Office+). For the remineralization treatment, different protective pastes (Tooth Mousse, MI Paste Plus, Remin Pro, and Profluorid Varnish) were evaluated. Specimens were randomly assigned to 10 groups of 5 specimens each. The specimens were analyzed under scanning electron microscopy. The superficial morphology of enamel was examined and scored as follows: 0, enamel with smooth surface morphology; 1, enamel with slight irregularities; 2, enamel with moderate irregularities; 3, enamel with accentuated irregularities. The photomicrographs were evaluated in a double-blind manner by three examiners, previously calibrated. Results were analyzed by a Kruskal-Wallis nonparametric test, at the significance level of 0.05. Dunn method posttest was applied for multiple comparisons. A different superficial morphology was observed among control group specimens and specimens treated with bleaching agent and protective pastes (p < 0.05). Enamel bleached showed pronounced surface changes and irregularities, significantly different from other groups except for groups 8 (enamel + Perfect Bleach Office+ + Remin Pro) and 10 (enamel + Perfect Bleach Office+ + Profluorid Varnish) (p > 0.05). The application of the tested pastes after bleaching is effective on repairing enamel surface morphology, demonstrating a higher efficacy for the CPP-ACP products compared to fluoridated ones. SCANNING 9999:1-6, 2015. © 2015 Wiley Periodicals, Inc.

Research paper thumbnail of Effect of self-assembling peptide P 11 -4 on enamel erosion: AFM and SEM studies

Scanning, 2016

The aim of the present in vitro study was to evaluate the protective effect of self-assembling pe... more The aim of the present in vitro study was to evaluate the protective effect of self-assembling peptide P11 -4 (Curodont™ Protect/Credentis) on enamel erosion produced by a soft-drink, by using Atomic Force Microscopy (AFM) and Scanning Electron Microscopy (SEM). Thirty human incisors were equally and randomly assigned to 6 groups. Group 1: intact enamel, group 2: soft drink, group 3: Curodont(™) Protect applied, group 4: Curodont(™) Protect applied + soft drink, group 5: soft drink + Curodont(™) Protect applied, group 6: soft drink + Curodont(™) Protect applied + soft drink. Specimens were observed through atomic force microscopy (AFM). The root mean-square roughness (Rrms) was obtained from the AFM images and the differences in the averaged values among the groups were analyzed by Shapiro-Wilk test in order to assess the normality of the distribution. Parametric ANOVA and post hoc Tuckey test were performed to assess the differences between the different groups. After demineralization process, enamel demonstrated a high degree of surface porosity. This morphological aspect was reflected in the increase of Rrms values. No significant differences (p > 0.05) were reported between intact enamel and enamel only treated with P11 -4 and between eroded enamel and enamel treated with P11 -4 and then demineralized. However significant differences (p < 0.05) were recorded when comparing softened enamel with softened enamel further remineralized with biomimetic self-assembling peptides and enamel treated with the protective paste between two acid attacks. The use of P11 -4 remineralizing may offer a degree of protection from enamel erosion. SCANNING 9999:1-8, 2015. © 2015 Wiley Periodicals, Inc.

Research paper thumbnail of Protective effect of casein phosphopeptide-amorphous calcium phosphate on enamel erosion: Atomic force microscopy studies

Research paper thumbnail of Biological and chemical-physical properties of root-end filling materials: A comparative study

Journal of Conservative Dentistry, 2015

Research paper thumbnail of Scattering properties of a composite resin: Influence on color perception

Contemporary Clinical Dentistry, 2014

The properties of the composite materials and the clinical expertise while layering them carry ma... more The properties of the composite materials and the clinical expertise while layering them carry many esthetic implications in restorative dentistry. The aim of the present study is to assess the influence of scattering properties of G-aenial A2 shade on color perception when used in esthetic restorations. TWO COMPOSITE RESINS WERE EVALUATED IN THIS STUDY: Gradia Direct (shade A3) and G-aenial (shade A2). A colorimetric evaluation according to the CIE L*a*b* system, relative to standard illuminant A against a white background, was performed to assess the referred chameleonic properties of G-aenial when used in simulated clinical situations. The differences in color change between the test group G-aenial and the test Group Gradia Direct were considered clinically not perceptible (ΔE* <3.3). Differently, the differences in color change were considered clinically perceptible (ΔE* >3.3) between the control group G-aenial and the control group Gradia Direct and between the test group G-aenial and the control specimens obtained with G-aenial. The CIE Lab parameters which brought to ΔE were investigated using t-test (P < 0.05). Color harmonization in simulated clinical conditions depends on different factors related to dentine and to composite resins. In this study dentine variables were dropped in order to analyze the influence of thickness and of the composition of the composite resin.

Research paper thumbnail of Decalcifying efficacy of different irrigating solutions: effect of cetrimide addition

Brazilian Oral Research, 2014

Research paper thumbnail of Ultrastructural analysis of the root canal walls after preparation with two rotary nickel-titanium endodontic instruments

Contemporary Clinical Dentistry, 2014

Root canal preparation may produce a large quantity of smear layer that covers canal walls. The a... more Root canal preparation may produce a large quantity of smear layer that covers canal walls. The aim of this study was to evaluate by Scanning Electron Microscope (SEM) the root canal dentine after instrumentation with nickel-titanium rotary files, in order to evaluate the presence/absence of smear layer and the presence/absence of open tubules on the root canal walls at the coronal, middle, and apical third of each sample. A total of 20 single-rooted freshly extracted teeth were selected and divided into two groups. For each group, root canals were shaped with Mtwo and Revo-S instruments under irrigation with Sodium hypochlorite and 17% ethylenediaminetetraacetic acid. Specimens were fractured longitudinally and SEM analyzed at standard magnification of ×1000 and ×5000. The presence/absence of smear layer and the presence/absence of open tubules at the coronal, middle, and apical third of each canal were evaluated using a three-step scale for scores. Numeric data were analyzed using the Kruskall-Wallis and Mann-Whitney U-Statistical tests and significance was pre-determined at P < 0.05. This study did not reveal differences among the two groups. Mtwo and Revo-S showed no significant difference between them and both presented very low smear layer scores and open tubules scores, with no significant difference among coronal, middle, and apical third. Mtwo and Revo-S rotary instruments seem to be effective in removing smear layer from canal walls.

Research paper thumbnail of Protective effect on enamel demineralization of a CPP–ACP paste: an AFM in vitro study

Journal of Dentistry, 2009

Research paper thumbnail of Cyclic fatigue resistance of OneShape, Reciproc, and WaveOne: An in vitro comparative study

Journal of Conservative Dentistry, 2014

Research paper thumbnail of Shear bond strength of one-step self-etch adhesives to enamel: effect of acid pretreatment

Dental Traumatology, 2014

Research paper thumbnail of Surface discoloration of composite resins: Effects of staining and bleaching

Dental Research Journal, 2012

Research paper thumbnail of Biocompatibility of a new pulp capping cement

Annali di Stomatologia, 2014

Research paper thumbnail of Remineralizzazione dello smalto esposto all’azione erosiva delle bevande acide

Prevenzione & Assistenza Dentale, 2010

Research paper thumbnail of Light intensity, temperature, and thickness dependence of the open-circuit voltage in solid-state dye-sensitized solar cells

Physical Review B, 2006

We present an analytical and experimental investigation into the origin of the open-circuit volta... more We present an analytical and experimental investigation into the origin of the open-circuit voltage in the solid-state dye-sensitized solar cell. Through Kelvin probe microscopy, we demonstrate that a macroscopically uniform electric field exists throughout the nanocomposite between the electrodes. Considering a balance between drift and diffusion currents, and between charge generation and recombination, we develop an analytical expression for the open-circuit voltage which accurately follows experimental data. We find the open-circuit voltage increases with light intensity as 1.7kT/q , where T is absolute temperature, however it decreases with increasing temperature and device thickness. The intensity dependence arises from the charge generation rate increasing more strongly with intensity than the recombination rate constant, resulting in increased chemical potential within the device. We find that the temperature dependence arises from a reduction in the charge lifetime and not from increased charge diffusion and mobility. The thickness dependence is found to derive from two factors; first, charge recombination sites are distributed throughout the film, enabling more charges to recombine in thicker films before influencing the potential at the electrodes, and second, the average optical power density within the film reduces with increasing film thickness.

Research paper thumbnail of High stability X-ray spectroscopy system with on-chip front-end in charge amplifier configuration

Nuclear Instruments and Methods in Physics Research Section A: Accelerators, Spectrometers, Detectors and Associated Equipment, 2003

Research paper thumbnail of Correlation between Surface Photovoltage and Blend Morphology in Polyfluorene-Based Photodiodes

Nano Letters, 2005

We present a microscopic study of photoinduced charge generation in polyfluorene-based photovolta... more We present a microscopic study of photoinduced charge generation in polyfluorene-based photovoltaic structures. The sub-100 nm lateral resolution of scanning Kelvin probe microscopy allows characterizing the three-dimensional structure of thin films of blends of poly-(9,9'-dioctylfluorene-co-benzothiadiazole) (F8BT) and poly-(9,9'-dioctylfluorene-co-bis-N,N'-(4-butylphenyl)-bis-N,N'-phenyl-1,4-phenylenediamine) (PFB). From the strong correlation between surface photovoltage and blend morphology, we propose a simple model for the lateral and vertical film structure identifying in particular those regions with the most efficient conduction pathway for the photocurrent.

Research paper thumbnail of Photovoltaic Performance and Morphology of Polyfluorene Blends:  The Influence of Phase Separation Evolution

Research paper thumbnail of Ultrastructural evaluation of enamel surface morphology after tooth bleaching followed by the application of protective pastes

Scanning, 2016

The aim of the present in vitro study was to evaluate the morphology of bleached enamel surface f... more The aim of the present in vitro study was to evaluate the morphology of bleached enamel surface followed by the application of different protective pastes. Specimens were prepared from 50 human incisors free of caries and defects. The bleaching procedure was performed with 35% hydrogen peroxide (Perfect Bleach Office+). For the remineralization treatment, different protective pastes (Tooth Mousse, MI Paste Plus, Remin Pro, and Profluorid Varnish) were evaluated. Specimens were randomly assigned to 10 groups of 5 specimens each. The specimens were analyzed under scanning electron microscopy. The superficial morphology of enamel was examined and scored as follows: 0, enamel with smooth surface morphology; 1, enamel with slight irregularities; 2, enamel with moderate irregularities; 3, enamel with accentuated irregularities. The photomicrographs were evaluated in a double-blind manner by three examiners, previously calibrated. Results were analyzed by a Kruskal-Wallis nonparametric test, at the significance level of 0.05. Dunn method posttest was applied for multiple comparisons. A different superficial morphology was observed among control group specimens and specimens treated with bleaching agent and protective pastes (p < 0.05). Enamel bleached showed pronounced surface changes and irregularities, significantly different from other groups except for groups 8 (enamel + Perfect Bleach Office+ + Remin Pro) and 10 (enamel + Perfect Bleach Office+ + Profluorid Varnish) (p > 0.05). The application of the tested pastes after bleaching is effective on repairing enamel surface morphology, demonstrating a higher efficacy for the CPP-ACP products compared to fluoridated ones. SCANNING 9999:1-6, 2015. © 2015 Wiley Periodicals, Inc.

Research paper thumbnail of Effect of self-assembling peptide P 11 -4 on enamel erosion: AFM and SEM studies

Scanning, 2016

The aim of the present in vitro study was to evaluate the protective effect of self-assembling pe... more The aim of the present in vitro study was to evaluate the protective effect of self-assembling peptide P11 -4 (Curodont™ Protect/Credentis) on enamel erosion produced by a soft-drink, by using Atomic Force Microscopy (AFM) and Scanning Electron Microscopy (SEM). Thirty human incisors were equally and randomly assigned to 6 groups. Group 1: intact enamel, group 2: soft drink, group 3: Curodont(™) Protect applied, group 4: Curodont(™) Protect applied + soft drink, group 5: soft drink + Curodont(™) Protect applied, group 6: soft drink + Curodont(™) Protect applied + soft drink. Specimens were observed through atomic force microscopy (AFM). The root mean-square roughness (Rrms) was obtained from the AFM images and the differences in the averaged values among the groups were analyzed by Shapiro-Wilk test in order to assess the normality of the distribution. Parametric ANOVA and post hoc Tuckey test were performed to assess the differences between the different groups. After demineralization process, enamel demonstrated a high degree of surface porosity. This morphological aspect was reflected in the increase of Rrms values. No significant differences (p > 0.05) were reported between intact enamel and enamel only treated with P11 -4 and between eroded enamel and enamel treated with P11 -4 and then demineralized. However significant differences (p < 0.05) were recorded when comparing softened enamel with softened enamel further remineralized with biomimetic self-assembling peptides and enamel treated with the protective paste between two acid attacks. The use of P11 -4 remineralizing may offer a degree of protection from enamel erosion. SCANNING 9999:1-8, 2015. © 2015 Wiley Periodicals, Inc.

Research paper thumbnail of Protective effect of casein phosphopeptide-amorphous calcium phosphate on enamel erosion: Atomic force microscopy studies

Research paper thumbnail of Biological and chemical-physical properties of root-end filling materials: A comparative study

Journal of Conservative Dentistry, 2015

Research paper thumbnail of Scattering properties of a composite resin: Influence on color perception

Contemporary Clinical Dentistry, 2014

The properties of the composite materials and the clinical expertise while layering them carry ma... more The properties of the composite materials and the clinical expertise while layering them carry many esthetic implications in restorative dentistry. The aim of the present study is to assess the influence of scattering properties of G-aenial A2 shade on color perception when used in esthetic restorations. TWO COMPOSITE RESINS WERE EVALUATED IN THIS STUDY: Gradia Direct (shade A3) and G-aenial (shade A2). A colorimetric evaluation according to the CIE L*a*b* system, relative to standard illuminant A against a white background, was performed to assess the referred chameleonic properties of G-aenial when used in simulated clinical situations. The differences in color change between the test group G-aenial and the test Group Gradia Direct were considered clinically not perceptible (ΔE* <3.3). Differently, the differences in color change were considered clinically perceptible (ΔE* >3.3) between the control group G-aenial and the control group Gradia Direct and between the test group G-aenial and the control specimens obtained with G-aenial. The CIE Lab parameters which brought to ΔE were investigated using t-test (P < 0.05). Color harmonization in simulated clinical conditions depends on different factors related to dentine and to composite resins. In this study dentine variables were dropped in order to analyze the influence of thickness and of the composition of the composite resin.

Research paper thumbnail of Decalcifying efficacy of different irrigating solutions: effect of cetrimide addition

Brazilian Oral Research, 2014

Research paper thumbnail of Ultrastructural analysis of the root canal walls after preparation with two rotary nickel-titanium endodontic instruments

Contemporary Clinical Dentistry, 2014

Root canal preparation may produce a large quantity of smear layer that covers canal walls. The a... more Root canal preparation may produce a large quantity of smear layer that covers canal walls. The aim of this study was to evaluate by Scanning Electron Microscope (SEM) the root canal dentine after instrumentation with nickel-titanium rotary files, in order to evaluate the presence/absence of smear layer and the presence/absence of open tubules on the root canal walls at the coronal, middle, and apical third of each sample. A total of 20 single-rooted freshly extracted teeth were selected and divided into two groups. For each group, root canals were shaped with Mtwo and Revo-S instruments under irrigation with Sodium hypochlorite and 17% ethylenediaminetetraacetic acid. Specimens were fractured longitudinally and SEM analyzed at standard magnification of ×1000 and ×5000. The presence/absence of smear layer and the presence/absence of open tubules at the coronal, middle, and apical third of each canal were evaluated using a three-step scale for scores. Numeric data were analyzed using the Kruskall-Wallis and Mann-Whitney U-Statistical tests and significance was pre-determined at P < 0.05. This study did not reveal differences among the two groups. Mtwo and Revo-S showed no significant difference between them and both presented very low smear layer scores and open tubules scores, with no significant difference among coronal, middle, and apical third. Mtwo and Revo-S rotary instruments seem to be effective in removing smear layer from canal walls.

Research paper thumbnail of Protective effect on enamel demineralization of a CPP–ACP paste: an AFM in vitro study

Journal of Dentistry, 2009

Research paper thumbnail of Cyclic fatigue resistance of OneShape, Reciproc, and WaveOne: An in vitro comparative study

Journal of Conservative Dentistry, 2014

Research paper thumbnail of Shear bond strength of one-step self-etch adhesives to enamel: effect of acid pretreatment

Dental Traumatology, 2014

Research paper thumbnail of Surface discoloration of composite resins: Effects of staining and bleaching

Dental Research Journal, 2012

Research paper thumbnail of Biocompatibility of a new pulp capping cement

Annali di Stomatologia, 2014

Research paper thumbnail of Remineralizzazione dello smalto esposto all’azione erosiva delle bevande acide

Prevenzione & Assistenza Dentale, 2010