Carbon Nanomaterials Based Saturable Absorbers for Ultrafast Passive Mode-Locking of Fiber Lasers (original) (raw)
Related papers
Mode-locked fiber lasers based on a saturable absorber incorporating carbon nanotubes
OFC 2003 Optical Fiber Communications Conference, 2003., 2003
This paper presents the first demonstration of passively mode-locked lasers based on a novel saturable absorber incorporating carbon nanotubes (SAINT). This device offers several key advantages over the conventional semiconductor saturable absorber mirror (SESAM) such as : ultra-fast recovery time ( <1ps), polarization insensitivity, exceptionally high optical damage threshold, mechanical and environmental robustness, chemical stability, and the ability to operate both in transmission, reflection and bi-directional modes. Moreover, the fabrication cost and complexity of SAINT devices are potentially much lower than that of the conventional SESAM devices. Therefore, we expect that SAINT will greatly impact future pulsed laser design and development, revolutionizing this industry.
Mode-locked 2 μm fiber laser with a multi-walled carbon nanotube as a saturable absorber
Chinese Optics Letters, 2015
We propose and demonstrate a passively mode-locked fiber laser operating at 1951.8 nm using a commercial thulium-doped fiber (TDF) laser, a homemade double-clad thulium-ytterbium co-doped fiber (TYDF) as the gain media, and a multi-walled carbon nanotube (MWCNT) based saturable absorber (SA). We prepare the MWCNT composite by mixing a homogeneous solution of MWCNTs with a diluted polyvinyl alcohol (PVA) polymer solution and then drying it at room temperature to form a film. The film is placed between two fiber connectors as a SA before it is integrated into a laser ring cavity. The cavity consists of a 2 m long TDF pumped by a 800 nm laser diode and a 15 m long homemade TYDF pumped by a 905 nm multimode laser diode. A stable mode-locking pulse with a repetition rate of 34.6 MHz and a pulse width of 10.79 ps is obtained when the 905 nm multimode pump power reaches 1.8-2.2 W, while the single-mode 800 nm pump power is fixed at 141.5 mW at all times. To the best of our knowledge, this is the first reported mode-locked fiber laser using a MWCNT-based SA. OCIS codes: 060.3510, 320.7090.
Mode-locked 2 \mu m fiber laser with a multi-walled carbon nanotube as a saturable absorber
Chinese Optics Letters, 2015
We propose and demonstrate a passively mode-locked fiber laser operating at 1951.8 nm using a commercial thulium-doped fiber (TDF) laser, a homemade double-clad thulium-ytterbium co-doped fiber (TYDF) as the gain media, and a multi-walled carbon nanotube (MWCNT) based saturable absorber (SA). We prepare the MWCNT composite by mixing a homogeneous solution of MWCNTs with a diluted polyvinyl alcohol (PVA) polymer solution and then drying it at room temperature to form a film. The film is placed between two fiber connectors as a SA before it is integrated into a laser ring cavity. The cavity consists of a 2 m long TDF pumped by a 800 nm laser diode and a 15 m long homemade TYDF pumped by a 905 nm multimode laser diode. A stable mode-locking pulse with a repetition rate of 34.6 MHz and a pulse width of 10.79 ps is obtained when the 905 nm multimode pump power reaches 1.8-2.2 W, while the single-mode 800 nm pump power is fixed at 141.5 mW at all times. To the best of our knowledge, this is the first reported mode-locked fiber laser using a MWCNT-based SA. OCIS codes: 060.3510, 320.7090.
Proceedings - Electronic Components and Technology Conference, 2009
Passively mode-locked lasers using saturable absorber incorporating dispersed single-wall carbon nanotubes (SWCNTs) is demonstrated. The peak absorption wavelength of saturable absorber can be engineered within the gain bandwidth of erbium-doped fiber (EDF) centered at 1550 nm. The mean diameter of SWCNTs and the linear optical absorption of SWCNTs-polyvinyl alcohol (PVA) film are verified by Raman spectroscopy and UV-Visible-NIR spectrophotometer. By integrating the SWCNTs-PVA film into EDF ring laser (EDFL) centered at 1550 nm, we observed three pulse mode operations, Q-switching, mode-locking, and 5 th-order harmonic mode-locking. The measured pulsewidths of the mode-locking and 5 th harmonic mode-locking EDFL are 4.2 ps and 2.7 ps, respectively.
Optics express, 2011
The dependence of thickness and concentration product (TCP) of single-wall carbon nanotubes saturable absorber (SWCNTs SA) on stabilizing and shortening pulsewidth in mode-locked fiber lasers (MLFLs) was investigated. We found that an optimized TCP for pulse energy and nonlinear self-phase modulation (SPM) enabled to determine the shorter pulsewidth and broader 3-dB spectral linewidth of the MLFLs. The shortest MLFL pulsewidth of 418 fs and broad spectral linewidth of 6 nm were obtained as the optimized TCP was 70.93 (μm•wt%), which was in good agreement with the area theorem prediction. This significant effect of TCP on pulse energy, SPM, pulsewidth, and spectral linewidth of MLFLs suggests that the TCP represents the total amount of SWCNTs in SA, which can be used as one of important and key parameters for characterizing the passive MLFL pulsewidth.
1300-NM Pulsed Fiber Lasers Mode-Locked by Purified Carbon Nanotubes
IEEE Photonics Technology Letters, 2000
For the first time, we demonstrate a novel passively mode-locked fiber laser operating at 1300 nm using purified singlewalled carbon nanotubes (CNTs) as a saturable absorber. The saturable absorber incorporates diameter-controlled CNTs with peak absorption 1300 nm, guaranteeing mode-locking over the same wavelength region. The ring laser uses praseodymium-doped fiber as a gain medium. The pulse repetition rate is 3.18 MHz, and the spectral half-width is 0.15 nm. Dual-wavelength mode-locking is also demonstrated with a channel spacing of 1.1 nm.
Laser Mode Locking Using a Saturable Absorber Incorporating Carbon Nanotubes
Journal of Lightwave Technology, 2004
This paper describes a new class of saturable absorber device based on single-wall carbon nanotube (SWNT)-the saturable absorber incorporating nano tube (SAINT). The device possesses ultrafast optical properties comparable to that of the industrial standard semiconductor saturable absorber mirror (SESAM). Passively mode-locked picosecond fiber lasers in different configurations are demonstrated using SAINTs as mode lockers. This is the first demonstration of optical pulsed lasers based on the carbon nanotube technology, and the first practical application of carbon nanotubes in the field of applied optics.
Laser Physics, 2013
The passive mode-locking of an erbium-doped fiber laser (EDFL) with a medium gain is demonstrated and compared by using three different types of carbon nanotubes (CNTs) doped in polyvinyl alcohol (PVA) films. Nano-scale clay is used to disperse the CNTs doped in the PVA polymer aqueous solution to serve as a fast saturable absorber to initiate passive mode-locking. The three types of CNT based saturable absorbers, namely single-walled (SW), double-walled (DW) and multi-walled (MW), are characterized by Raman scattering and optical absorption spectroscopy. The SW-CNTs with a diameter of 1.26 nm have two absorption peaks located around 1550 ± 70 and 860 ± 50 nm. In contrast, the DW-CNTs with a diameter of 1.33 nm reveal two absorption peaks located at 1580 ± 40 and 920 ± 50 nm. By using the SW-CNT based saturable absorber, the passively mode-locked EDFL exhibits a pulsewidth of 1.28 ps and a spectral linewidth of 1.99 nm. Due to the increased linear absorption of the DW-CNT based saturable absorber, the intra-cavity net gain of the EDFL is significantly attenuated to deliver an incompletely mode-locked pulsewidth of 6.8 ps and a spectral linewidth of 0.62 nm. No distinct pulse-train is produced by using the MW-CNT film as the saturable absorber, which is attributed to the significant insertion loss of the EDFL induced by the large linear absorption of the MW-CNT film.
Passive mode locking in erbium-doped fibre laser by carbon nanotubes
2011 Conference on Lasers and Electro-Optics Europe and 12th European Quantum Electronics Conference (CLEO EUROPE/EQEC), 2011
A C-band mode-locked fibre laser incorporating a boron nitride-doped graphene oxide (BN-GO)based saturable absorber (SA) is proposed and demonstrated. The SA is fabricated by depositing multiple layers of synthesized BN-GO nanoparticles onto the polished surface of a side-polished fibre, which is then inserted into an erbium-doped fibre laser cavity to generate the desired pulsed output. The strong nonlinear optical response and light absorption of the BN-GO nanoparticles induces the generation of a highly stable mode-locked pulse at 1567.32 nm with visible Kelly's sidebands. The pulses have a measured repetition rate of 13.56 MHz and a pulse width of 1.18 ps at the maximum pump power of 280.5 mW. The pulses have a frequency signal-to-noise ratio of ∼ 53 dB, indicating a highly stable output. The proposed laser would find significant telecommunications applications, particularly for dense wavelength division multiplexing systems.