A high-efficiency HBT-based class-E power amplifier for 2 GHz (original) (raw)
Related papers
Design of a 2 GHz GaAs HBT-based Class-E power amplifier
This paper presents a design procedure for the GaAs HBT-based Class-E power amplifier for 2 GHz. An empirical approach, based on load-pull and source-pull sim- ulations has been used to find an optimal impedance point for high efficiency operation. The simulation results show that a single-stage single-ended Class-E PA can achieve PAE higher than 70 %, output power of 24 dBm and transducer power gain of 15 dB when driven from a standard 50 Ohm signal generator. Three different solutions for the imple- mentation of the load network are discussed, including both lumped and distributed components. designed and implemented in various technologies and in different frequency bands. In many papers it is shown how the circuit deviates from its nominal operation when dif- ferent kinds of non-ideal effects are taken into account. These effects include finite-inductance DC-feeding coil, finite Q-factor of the load network, non-zero fall time of the collector/drain current, variations in duty c...
A 1.8 GHz Power Amplifier Class-E with Good Average Power Added Efficiency
Circuits and Systems, 2013
This paper presents a 1.8 GHz class-E controlled power amplifier (PA). The proposed power amplifier is designed with two-stage architecture. The main advantage of the proposed technique for output control power is a high 37 dB output power dynamic range with good average power adding efficiency. The measurement results show that the PA achieves a high power gain of 23 dBm and power added efficiency (PAE) by 38%. The circuit was post layout simulated in a standard 0.18 μm CMOS technology.
A 1GHZ CLASS E POWER AMPLIFIER FOR WIRELESS APPLICATIONS
In this paper, a class E power Amplifier (PA) suitable for wireless applications (Wi-Max, cellular phones, cordless phones etc,) is proposed by using the device of RF3931GaN HEMT (Gallium Nitrate High Electron Mobility Transistor).The proposed class E power Amplifier for achieving high output power and increasing gain up to 14.327dB and operates in the frequency range of 1GHz. The designed Power Added Efficiency (PAE) is 64% after optimization and the maximum source power achieved is 32dBw.
TURKISH JOURNAL OF ELECTRICAL ENGINEERING & COMPUTER SCIENCES, 2014
A linearization technique for improving the class-E power amplifier (PA)'s adjacent channel power ratio (ACPR) is proposed. The design is simulated in a 2-µ m InGaP/GaAs heterojunction bipolar transistor process. The integration of a passive predistorter at the input of the PA linearizes the proposed architecture. At a 29-dBm output power, the PA's ACPR is indicated to be-51 dBc, meeting the stringent code division multiple access regulation. At this exact output power, the simulated power added efficiency is 55% with the collector voltage headroom consumption of 3.4 V. The input return loss, S11, of the PA is simulated as-12.5 dB. With an active finger print dimension of 1000 µ m × 750 µ m, the proposed PA is well suited for the application of mobile wireless communication.
Analysis and Design a 2.5 GHz Class-E Power Amplifier in Two Configurations
There are two circuit configurations that commonly used for Class-E power amplifiers, the Infinite DC-feed or Shunt capacitor configuration and the Finite DC-feed or Shunt inductor. Albeit these circuit configurations are not essentially different, however they show different behavior and performance. In this paper we have compared these Class-E configurations at 2.5 GHz. For this purpose, we have designed two class-E circuits, one with Infinite DC-feed configuration and the other with Shunt inductor configuration. We have used the GaN High Electron Mobility Transistor (HEMT) in both designs. Optimized simulations showed 69% drain efficiency, 64% PAE, and 21.46 dBm load power, in the case of Infinite DC-feed design and 71% efficiency, 64.5% PAE, and 15.93 dBm load power in the case of Shunt inductor design. It is obvious that we should consider the importance of PAE inhigh power circuits and the importance of DE in low power circuits. The results propose that Infinite DC-feed design...
A 20 dBm Q-band SiGe Class-E power amplifier with 31% peak PAE
Proceedings of the IEEE 2012 Custom Integrated Circuits Conference, 2012
A Q-band two-stage Class-E power amplifier is designed and fabricated in a 0.13 µm SiGe HBT BiCMOS process. A mm-wave Class-E architecture considering the effect of various interconnect parasitics is adopted to achieve high power efficiency. Proper input and output networks have been designed to enable efficient switching of the HBT at large voltage swings without causing unwanted impact ionization-induced negative base current and instability. The measured performance of the fabricated chip show 20.2 dBm maximum output power, 31.5% peak power added efficiency, and 10.5 dB power gain across 4 GHz centered around 45 GHz for a supply voltage of 2.5 V. The total chip area including the pads is 0.74 mm × 1.7 mm.
A 2.45 GHz 30dBm differential 0.18 μm CMOS class-E power amplifier with 42% PAE
This paper presents a 30dBm (1W) class-E power amplifier projected in a standard 0.18-μm CMOS technology. The power amplifier (PA) consists in two differentials stages. The main stage employs a cascode class-E RF power amplifier with a self-biasing circuit. The driver stage uses the technique of Injection-Locking to substantially reduce the input power signal, maintaining a high gain. At 2.45 GHz, the power amplifier achieves power added efficiency (PAE) of 42% at an output power of 30 dBm, with a total gain of 28 dB.
A Monolithic X-band Class-E Power Amplifier
Low cost, highly efficient, high power, microwave and RF amplifiers are required for many commercial and defense system applications, including WLANs, cellular phones, and advanced air-borne active phased array radar systems. This paper describes what is believed to be the first successful design and fabrication of a broadband monolithic high efficiency class-E driver amplifier that operates at X-band, and employs a 0.3 um x 600 um pseudo high electron mobility transistor (pHEMT) device. L ow cost, highly efficient, high power, microwave and RF amplifiers are required for many commercial and defense system applications. These include WLANs, wireless cable broadcast transmitters, cellular phones, and telecommunication systems, as well as advanced air-borne active phased array radar systems.
Design of high efficiency class e power amplifier in l band
International Journal for Scientific Research and Development, 2015
In Modern Base station, at the transmitter side, a power amplifier is used to increase the signal power and allow longer distance transmission. The rapid growth in wireless communications and radar applications creates many challenges in performance of power amplifiers. Microwave L band is very useful in Long Distance Radar, Private Radio, Navigation system and Mobile communication so it is desirable to use high efficiency Power amplifier at transmitter side because most of power dissipation take place at active devices used in amplifier. In this paper Class E Switched mode topology is discussed because of high efficiency and low switching loss.
Investigation on technological aspects of class E RF power amplifiers for umts applications
This paper presents results of investigation on the effects of technology on the performance of the class E power amplifier circuit. A typical class E circuit has been designed and simulated, for a typical UMTS Tx frequency (1.95 GHz) and output power ( 27dBm). Three different technologies have been used (silicon BJT, CMOS and GaAs HBT) and several important parameters (output efficiency, power added efficiency, stress put on the device) have been monitored and put in table form for comparison. Care has been taken to adapt the design in such a way to provide a maximum performance with each technology, for a fair comparison. The results are then analyzed and different tradeoffs are discussed. Possibilities for the linearization of the amplifier are considered.