Preparation and characterization of polyvinyl alcohol based nanocomposite membrane for direct methanol fuel cell (original) (raw)
Related papers
Journal of Applied Polymer Science, 2008
Layered silicate nanocomposite membranes to be used as electrolyte polymeric membranes in a direct methanol fuel cell were prepared through the mixing of poly(vinyl alcohol) (PVA) with various amounts (2, 4, and 5% w/w) of sodium montmorillonite layered silicate nanoclay. The proton conductivity of the polymer was induced by the reaction of the polymer with sulfosuccinic acid. After that, a solution of the sulfonated PVA-layered silicate nanocomposite was cast into membranes. The proton conductivity and methanol permeability of the membranes were determined with a four-point probe technique and a gas chromatography technique, respectively. In addition, structures of the nanocomposite membranes were characterized with X-ray diffraction, differential scanning calorimetry, and Fourier transform infrared techniques. The mechanical properties of the nanocomposite membranes were also determined with a universal testing machine. From the results, it was found that the water uptake, proton conductivity, and methanol permeability of the membranes initially decreased after a 2% (w/w) concentration of the layered silicate was added. Above this nanoclay loading, the water uptake of the membranes increased again. The results were examined in the light of the interaction between the clay and sulfonated polymer, and the steric effect provided the exfoliation of the nanoclay.
Asia-Pacific Journal of Chemical Engineering, 2017
Sulfonated polyvinylalcohol‐mordenite (SPVA‐MOR) membranes for direct methanol fuel cell use were synthesized and characterized. It had earlier been found out that polyvinylalcohol‐mordenite (PVA‐MOR) membranes, while having excellent methanol permeability and modest proton conductivity values, had inferior direct methanol fuel cell performances than Nafion™. Sulfonating the polyvinylalcohol matrix had been suggested to improve the proton conductivity. In this work, polyvinylalcohol powder was sulfonated by using propane sultone as the sulfonating agent prior to the membrane synthesis. Morphological analyses revealed that the zeolite particles mixed homogeneously within the polymer matrix. Sulfonating the polymer slightly decreased both water and methanol uptakes. Both in PVA‐MOR and SPVA‐MOR membranes, water uptake turned out to be higher than the methanol uptake. SPVA‐MOR membranes were found to have an average proton conductivity of 0.052 S·cm−1 when compared with the 0.036 S·cm−...
Polyvinylalcohol–mordenite (PVA–MOR) mixed matrix membranes were synthesized for direct methanol fuel cell (DMFC) use. For the structural and the morphological characterization, Scanning Electron Microscopy and Thermal Gravimetric Analysis methods were used. Zeolite distribution within the polymer matrix was found to be homogeneous. An impedance spectroscope was used to measure the proton conductivity. In order to obtain information about methanol permeation characteristics, swelling tests and a series of pervaporation experiments were carried out. 60–40 wt% PVA–MOR membranes were found to give the optimum transport properties. Proton conductivity of these membranes was found to be slightly lower than that of Nafion117 TM whereas their methanol permeability was at least two orders of magnitude lower than Nafion117 TM. DMFC performance of the PVA–MOR membranes was also measured. The inferior DMFC performance of PVA–MOR membranes was linked to drying in the fuel cell medium and the consequent proton conductivity loss. Their performance was improved by adding a dilute solution of sulfuric acid into the feed methanol solution. Future studies on the improvement of the proton conductivity of PVA–MOR membranes, especially via sulfonation of the polymer matrix, can overcome the low-performance problem associated with insufficient proton conductivity.
Materials Science-Poland
Proton exchange membranes have been synthesized from polyimide (PI) doped with different contents of montmorillonite (MMT) which was obtained by solution casting technique. The enhancement of conductivity was achieved through modification with the MMT. Prepared membranes were systematically characterized in terms of ion exchange capacity, water uptake, methanol uptake, swelling behavior and proton conductivity. Fourier transform infrared spectroscopy and X-ray diffraction measurements were used to confirm the structures of the PI/MMT composite electrolyte membranes. SEM surface morphological images of the composite membranes showed that the MMT nanoclay particles were dispersed uniformly within the membrane what was also reflected in XRD results which indicated a good compatibility of MMT particles with the polymer complex. The TGA spectra showed that the thermal stability of the membrane was reduced by adding MMT into the polymer network. The prepared membrane with 10 wt.% of modif...
Journal of Applied Polymer Science, 2007
Sulfonated poly(vinyl alcohol) (PVA) for use as a proton conductive membrane in a direct methanol fuel cell (DMFC) was prepared by reacting the PVA with sulfoacetic acid and poly(acrylic acid). The effects of the amount of sulfoacetic acid and poly(acrylic acid) on proton conductivity, methanol permeability, water uptake, and ion exchange capacity (IEC) of the sulfonated PVA membranes were investigated by using impedance analysis, gas chromatography, gravimetric analysis, and titration techniques, respectively. The water uptake of the membranes decreased with the amount of the sulfoacetic acid and the amount of poly(acrylic acid) used. The proton conductivity and the IEC values of the membranes initially increased and then decreased with the amount of the sulfoacetic acid. The methanol permeability of the sulfonated PVA membranes decreased continuously with the amount of the sulfoacetic acid.
Polymers, 2021
In this study, chemically cross-linked PVA/PAMPS membranes have been prepared to be used in direct methanol fuel cells (DMFCs). The structural properties of the resultant membrane were characterized by use FTIR and SEM. Additionally, their thermal stability was assessed using TGA. Moreover, the mechanical properties and methanol and water uptake of membrane was studied. The obtained FTIR of PVA/PAMPS membranes revealed a noticeable increase in the intensity of adsorption peaks appearing at 1062 and 1220 cm−1, which correspond to sulfonic groups with the increasing proportion of PAMPS. The thermograms of these polyelectrolyte membranes showed that their thermal stability was lower than that of PVA membrane, and total weight loss gradually decreased with increasing the PAMPS. Additionally, the functional properties and efficiency of these polyelectrolyte membranes were significantly improved with increasing PAMPS proportion in these blends. The IEC of polymer blend membrane prepared u...
IOP Conference Series: Materials Science and Engineering, 2015
Different concentrations of Poly (vinyl alcohol)/Montmorillonite (PVA/MMT) based proton exchange membranes (PEMs) have been prepared by solution casting method. The structural and electrical properties of these composite membranes have been characterized by using X-ray diffraction (XRD), Fourier transform infrared spectroscopic (FTIR) and AC impedance spectroscopic methods. The conductivity of the PEMs has been estimated for the different concentration of MMT. Water/Methanol uptake measurement were also analyzed for the prepared PEMs and presented. The proton conductivity studies were carried out at room temperature with 100% of humidity.
Polymer Testing, 2020
Proton-conducting and methanol barrier properties of the proton exchange membrane (PEM), as well as the high cost of direct methanol fuel cell (DMFC) components, are the key determinants of the performance and commercialization of DMFCs. Therefore, this study aimed to develop cost-and performance-effective membranes based on sulphonated poly (vinyl chloride) (SPVC)/poly (2-acrylamido-2-methyl-1-propane sulphonic acid) (PAMPS) blends. Such membranes have been simply prepared by blending SPVC and PAMPS solutions, followed by solvent evaporation via casting. Interaction of SPVC with PAMPS was confirmed by different characterization techniques such as Fourier Transform Infra-red (FTIR) and Raman scattering spectroscopy in which the two characteristic absorption bands of sulfonic groups appeared at 1093 and 1219 cm À 1 additionally, strong peaks at around 1656 cm À 1 attributed to vibration of amide groups of PAMPS portion in the polymer blend. Furthermore, the interaction of SPVC with PAMPS improves the thermal properties along with ion exchange capacity in turn decreasing the methanol permeability through the membrane in comparison with the SPVC membrane. The IEC of PVC and Nafion 117 membranes were 1.25, 0.91 meq/g; respectively. And the maximum water uptake of PVC and Nafion 117 membranes were 75 and 65.44%; respectively. Methanol permeability value of 7.7 � 10 À 7 cm 2 /s which was noticeably lower than the corresponding value recorded for Nafion® (3.39 � 10 À 6 cm 2 /s). Therefore, these fabricated membranes can be considered a low-cost efficient candidate for use in DMFC, especially for its capability to resolve the methanol cross-over issue.
Journal of Applied Membrane Science & Technology, 2022
The development of potential and novel proton exchange membrane (PEMs) is imperative for further commercialization of Direct Methanol Fuel Cell (DMFC). In this study, flat sheet hybrid membrane as an alternative PEM made up of polyvinyl alcohol (PVA) and mesoporous phosphotungstic acid-Silica (mPTA-Si) at various loadings of 0.5, 1.0, 1.5 and 2.0 wt% was prepared to examine the desirable properties for DMFC application. The characteristic test such as water uptake and proton conductivity were conducted. As the mPTA-Si loading increases, the proton conductivity of PVA/mPTA-Si membrane increased up to 1.81 x 10-3 Scm-1 with 68% of water uptakes. The obtained results could reflect the enhance performance of mPTA-Si membrane and high potential alternative membrane for DMFC. Scanning Electron Microscopy (SEM) and Fourier Transform Infrared Spectroscopy (FTIR) results proved a good dispersion and the existence of Keggin anion from mPTA-Si particles formed a strong interfacial bonding betw...
2007
Sulfonated poly(ether ether ketone) (SPEEK) membranes have been prepared as a potential polymer electrolyte membrane (PEM) for direct methanol fuel cell (DMFC) application. The SPEEK polymer was dissolved into N, N-dimethylacetamide (DMAc) in a subsequent step after sulfonating the raw polymer with concentrated sulfuric acid. The polymer solutions were then cast by pneumatic casting machine. The influence of sulfonation reaction temperature on ion exchange capacity (IEC) and degree of sulfonation (DS) have been investigated. The results showed that the IEC and DS are increased with the temperature. The resulting membranes were then characterized by evaluating their physicochemical properties such as methanol permeability and proton conductivity as a function of DS. The overall results showed that sulfonation process successfully enhanced the proton conductivity of the membrane and the values were comparable with commercial membrane, Nafion ® 117, at room temperature. Although the methanol permeability of membrane also increased after sulfonation process and proportional with DS, the value was still lower than Nafion ® 117.