Preparation and Characterization of Bionanocomposites Based on Benzylated Wheat Straw and Nanoclay (original) (raw)
Related papers
Novel bionanocomposites: processing, properties and potential applications
Plastics, Rubber and Composites, 2009
The demand for environmental sustainability has resulted in a great interest in finding new materials that are biodegradable and environmentally friendly. Therefore, materials derived from natural resources are now being extensively studied. Preparation of novel biocomposites based on nanocelluloses has drawn specific attention. It is expected that cellulose nanocomposites will open new areas for applications in medicine, packaging, electronics, the automotive sector, construction and other areas. This article presents a new research field of bionanocomposites where different types of nanocelluloses are used as reinforcements in biopolymers. Isolation of cellulose nanofibres and nanowhiskers from different sources, and processing technologies for the composites, are described and discussed. The main difficulty when producing cellulose based nanocomposites is to disperse the reinforcement in the polymer matrix without degradation of the biopolymer or the reinforcing phase. This can be addressed by improving the interaction (compatibility) between nanofibres and the matrix and by using suitable processing methods. The study of alignment of the nanocelluloses by using magnetic field is discussed and the nanocomposites' mechanical properties, based on the findings from different studies, are presented. Finally, some examples of future nanocomposites are discussed.
Cellulosic bionanocomposites: A review of preparation, properties and applications
2010
Cellulose is the most abundant biomass material in nature. Extracted from natural fibers, its hierarchical and multi-level organization allows different kinds of nanoscaled cellulosic fillers-called cellulose nanocrystals or microfibrillated cellulose (MFC)-to be obtained. Recently, such cellulose nanoparticles have been the focus of an exponentially increasing number of works or reviews devoted to understanding such materials and their applications. Major studies over the last decades have shown that cellulose nanoparticles could be used as fillers to improve mechanical and barrier properties of biocomposites. Their use for industrial packaging is being investigated, with continuous studies to find innovative solutions for efficient and sustainable systems. Processing is more and more important and different systems are detailed in this paper depending on the polymer solubility, i.e., (i) hydrosoluble systems, (ii) non-hydrosoluble systems, and (iii) emulsion systems. This paper intends to give a clear overview of cellulose nanoparticles reinforced composites with more than 150 references by describing their preparation, characterization, properties and applications.
A Review: Emerging Trends in Bionanocomposites
International Journal of Pharmacy Research & Technology, 2021
In recent year's development of different type of bionanocomposites have increased their utilization in biomedical and pharmaceutical science. Bionanocomposites have huge potentional as future green materials comprised of biopolymer and their composites that prove to be a cost effective solution over petro based polymer. The present manuscript gives detail insight into components of biopolymers, preparation technique of bionanocomposites, characterization, properties and applications of bionanocomposites in pharmaceutical field.
Biobased plastics and bionanocomposites: Current status and future opportunities
Progress in Polymer Science, 2013
This paper presents a broad review on the recent advances in the research and development of biobased plastics and bionanocomposites that are used in various applications such as packaging, durable goods, electronics and biomedical uses. The development of biobased materials is driven by renewability, low carbon footprint and in certain cases biodegradability (compostability) issues and helped them in moving from niche markets to high-volume applications. The inherent drawbacks of some biobased plastics such as the narrow processing window, low heat deflection temperatures, hydrophilicity, poor barrier, and conductivity and inferior biocompatibility can be overcome by bionanocomposites. The first part of the paper reviews the recent advances in the development of biobased and biodegradable materials from renewable resources and their advantages and disadvantages. In the second part, various types of bionanocomposites based on four types of fillers i.e. nanocellulose, carbon nanotubes, nanoclays, and other functional nanofillers are discussed. This review also presents up-to-date progress in this area in terms of processing technologies, product development and applications.
Biodegradable Nanocomposites from Wheat Straw
2006
We investigate the mechanical and thermal properties of cellulose nanofiber reinforced starch based thermoplastic composites. Cellulose nanofibers were isolated from wheat straw by a chemi-mechanical technique. Their morphology, physicochemical and thermal properties were investigated to examine potential applications as reinforcement fibers in biocomposites. Transmission electron microscopy results showed that almost 60% of them have a diameter within a range of 30-40 nm and lengths of several thousand nanometers. Their average aspect ratio was found to be 95. Chemical characterization of the nanofibers confirmed that an applied alkali and acid treatment resulted in increased cellulose content from 43% to 85%. FT-IR spectroscopic analysis of the fibers demonstrated that this chemical treatment also led to partial removal of hemicelluloses and lignin from the nanofibers' structure. PXRD measurements revealed that this resulted in an improved crystallinity of the fibers. After mechanical treatments, thermal properties of the nanofibers were studied by the TGA technique and found to increase dramatically. The nanocomposites were prepared by a solution casting method. The tensile strength and modulus of the reinforced starch films were compared with those of pure starch and were found to have considerably improved, even at 5% nanofiber loading.
European Polymer Journal, 2013
In the aim of producing fully organic bionanocomposite based on poly(lactide) (PLA), cellulose nanowhiskers (CNW) were grafted by n-octadecyl-isocyanate (CNW-ICN) applying an in situ surface grafting method. The compatibilizing effect of the long aliphatic grafted chain was investigated by thermal, mechanical and permeability analysis of solvent cast nanocomposite films. The grafted CNW-ICN could be successfully dispersed in the polymer matrix. The gained compatibility brought about a nucleating effect, decreasing the half time of isothermal crystallization from 25 min for the neat PLA to 8.4 min for the nanocomposite including 2.5 wt% CNW-ICN, e.g., tensile strength was improved by 10 MPa for the same 2.5 wt% CNW-ICN/PLA composite. Mechanical reinforcement was also effective in the rubbery state of PLA and increased the tensile modulus of the rubbery plateau providing thereby thermal resistance to the polymer. Oxygen barrier properties did not change significantly upon the inclusion of CNW-ICN, even when the quantity of CNW-ICN was increased to 15 wt%. More interestingly, the water vapour permeability of the CNW-ICN nanocomposite was always lower than the one of ungrafted CNW composites, which led to the conclusion that the hydrophobic surface graft and improved compatibility could counteract the effect of inclusion of hydrophilic structures in the matrix on water vapour transport. In conclusion, the surface grafting of CNW with isocyanates might be an easy and versatile tool for designing fully organic bionanocomposites with tailored properties. Ó
2017
Bionanocomposites of poly(lactic acid) (PLA) and nanocrystalline cellulose (NCC) have the potentials to be used in various applications because of their biodegradability and renewability. However, due to their significant differences in hydrophobicity, it creates dispersibility and compatibility problems. To reduce these shortcomings, the NCC is modified via the silylation reaction using 3-aminopropyltriethoxysilane (APS). The NCC used in this research was isolated from unbleached OPEFB pulp using a combination of TEMPO oxidation and ultrasonic treatment, with solvent casting using chloroform employed for the preparation of the PLA-NCC bionanocomposite
Synthesis And Characterization Of Cellulose Nanocrystals/PVA Based Bionanocomposite
Advanced Materials Letters, 2013
Sugarcane bagasse based cellulose nanocrystals (CNCs) and poly (vinyl alcohol) (PVA) were used to fabricate biodegradable porous foam bionanocomposites for application in biomedical applications by thermally-induced phase separation (TIPS) (freeze drying) technique. Aqueous suspension of cellulose nanocrystals and poly (vinyl alcohol) (PVA) solution in water were mixed to prepare (20/80) (v/v) composition of these polymers. For the comparative study 3D porous PVA foam was also prepared. Samples were characterized by FE-SEM, FTIR, X-ray diffraction analysis, porosity and pore size by ImageJ software. FE-SEM showed the surface morphology of pores distribution of the foam samples. The porosity of 3D porous PVA foam and 3D porous CNCs/PVA bionanocomposite was calculated as 90.8% and 89.0% respectively. The functional groups and crystallinity of the samples were determined by FTIR and X-ray diffraction spectra, respectively. The diameter of CNCs was in the range from 29 nm to 65 nm and the average diameter was calculated as 43± 3 nm by image analysis using ImageJ software. Thus produced porous composite in the present study might find potential applications to be used in biomedical applications.