tapered laser diodes (original) (raw)

Author: the photonics expert

Definition: laser diodes containing a tapered region for achieving a higher beam quality

Category: laser devices and laser physics

DOI: 10.61835/8uz [Cite the article](encyclopedia%5Fcite.html?article=tapered laser diodes&doi=10.61835/8uz): BibTex plain textHTML Link to this page LinkedIn

Single-mode laser diodes can produce laser light with high beam quality, but only with a modest optical power of e.g. some tens of milliwatts. For much higher output powers, one can use broad area laser diodes, having a broad emitting region; these, however, typically have a much reduced beam quality and therefore only a moderate amount of radiance (brightness). For achieving the combination of high output power and high beam quality, tapered laser diodes have been developed. They may be called high brightness laser diodes. While their output powers are similar to those of broad area laser diodes (tentatively somewhat lower), their _M_2 factor is typically of the order of 2, i.e., not very far from diffraction-limited.

Operation Principle

Figure 1: Simplified setup of a tapered semiconductor laser diode. The blue area is the active area, which also acts as a waveguide at least in the vertical dimension.

A tapered laser diode has a semiconductor chip design which is similar to that of a tapered amplifier diode. The most essential difference is that while laser operation is suppressed in a tapered amplifier by minimizing reflections from the end faces, a tapered laser diode exhibits such end reflections, so that it can lase without external optical feedback. The back side is typically equipped with a high reflectivity, while the reflectivity of the front face is relatively small. One may also integrate a Bragg grating into the small waveguide region for selecting the emission wavelength and reducing the emission linewidth.

In contrast to an ordinary broad area laser diode, where the width of the active region is constant along the whole length, a tapered laser diode exhibits substantial additional power losses for light getting back from the output side into the small waveguide. This is associated with the spatial filtering action which improves the beam quality. Some of the returning light might cause optical pumping of regions outside the small waveguide, which is unwanted; in order to prevent that, one may make that region absorbing with additional means (e.g. by applying a reverse bias voltage in that region), or include some additional trenches for eliminating such light. The mentioned additional filter loss does not necessarily have a strong impact on the power conversion efficiency, particularly if the front face reflectivity is small. The details of laser operation with mode filtering are complicated, and one requires sophisticated simulation models to analyze the details and optimize the device design.

In the horizontal direction, the laser resonator of a tapered laser diode can be considered as an unstable resonator, having the characteristic property of high diffraction losses.

Tapered Diode Bars

Some diode bars are made from tapered laser diodes instead of ordinary broad area laser diodes. That results in substantially improved beam quality and an accordingly higher radiance (brightness). While the emission of different emitters is still normally mutually incoherent, the beam divergence in the horizontal direction is substantially reduced.

Further substantial increases of radiance are possible with techniques of beam combining – for example, spectral beam combining, where the different emitters operate at slightly different wavelengths.

External-cavity Diode Lasers with Tapered Amplifiers

It is also possible to fabricate external-cavity diode lasers where the gain medium is a tapered amplifier. See the article on tapered amplifiers for more details.

More to Learn

Encyclopedia articles:

• tapered amplifiers
• broad area laser diodes
• diode bars
• high brightness laser diodes

Suppliers

Bibliography

(Suggest additional literature!)

Questions and Comments from Users

Here you can submit questions and comments. As far as they get accepted by the author, they will appear above this paragraph together with the author’s answer. The author will decide on acceptance based on certain criteria. Essentially, the issue must be of sufficiently broad interest.

Please do not enter personal data here. (See also our privacy declaration.) If you wish to receive personal feedback or consultancy from the author, please contact him, e.g. via e-mail.

By submitting the information, you give your consent to the potential publication of your inputs on our website according to our rules. (If you later retract your consent, we will delete those inputs.) As your inputs are first reviewed by the author, they may be published with some delay.