dispersion compensation modules (original) (raw)

Acronym: DCM

Definition: modules used for dispersion compensation

Categories: article belongs to category lightwave communications lightwave communications, light pulses

dispersion
- dispersion compensation
  * dispersion compensation modules
  * electronic dispersion compensation

Page views in 12 months: 855

DOI: 10.61835/0xe Cite the article: BibTex BibLaTex plain text HTML Link to this page! LinkedIn

Content quality and neutrality are maintained according to our editorial policy.

In optical fiber communications, dispersion compensation modules (DCM) (also called dispersion compensation units, DCU) can be used for compensating the chromatic dispersion of, e.g., a long span of transmission fiber. Typically, such a module provides a fixed amount of dispersion (e.g. normal dispersion in the 1.6-μm spectral region, with some wavelength dependence of the group delay dispersion), although tunable dispersion modules are also available. A module can easily be inserted into a fiber-optic link because it has fiber connectors for the input and output. The insertion losses may be significant, but may be compensated with a fiber amplifier, e.g. an erbium-doped fiber amplifier in a 1.5-μm telecom system. A dispersion-compensating module is often placed between two fiber amplifiers.

Dispersion compensation modules can be based on different technologies:

A simple and frequently used method employs a long piece of fiber, e.g. a dispersion-shifted fiber, wound up on a spool with a diameter of e.g. 100–200 mm. The fiber used can be optimized to provide dispersion for the compensation of e.g. a 100-km span of transmission fiber, while introducing an insertion loss of only a few decibels.
A more compact approach, also possibly presenting even lower insertion loss, is based on a chirped fiber Bragg grating. A large amount of dispersion can be compensated with relatively long fiber gratings (possibly tens of centimeters in length). By varying the device temperature (with built-in temperature gradients), the dispersion may be tuned.
For wavelength division multiplexing systems, virtually imaged phased arrays are sometimes used.

Key Performance Parameters

Various properties of dispersion compensation modules can be important:

A central aspect is of course the amount of group delay dispersion provided (e.g. in units of ps2, or ps/nm), which depends on the length of transmission fiber to be compensated, and on the type of transmission fiber. For example, dispersion-shifted transmission fibers usually require much less dispersion compensation.
The dispersion slope (higher-order dispersion) e.g. in units of ps/nm2 may strongly limit the usable bandwidth, which is important particularly in the case of wavelength division multiplexing. Depending on the type of transmission fiber, different relative dispersion slopes are required.
In some cases, tunable dispersion is desirable.
Optical insertion losses may result e.g. from absorption and scattering in a fiber, but also from splice and connector losses. Such losses should be low, since they require a high amplifier gain and lead to higher excess noise.
In some cases, the amount of optical nonlinearity (e.g. favoring four-wave mixing) can be relevant. This is minimized e.g. by using strongly dispersive fiber, where a shorter length is sufficient.
Compactness can be an important practical aspect. Tight winding of the compensating fiber can be a solution, but is limited by bend losses.

For very high single-channel data rates, compensation of polarization mode dispersion can also be required. This is substantially more complicated, since it is necessary for that purpose to monitor the state of the signal and correct the time delays accordingly.

Frequently Asked Questions

This FAQ section was generated with AI based on the article content and has been reviewed by the article’s author (RP).

What is a dispersion compensation module (DCM)?

A dispersion compensation module is a device used in optical fiber communications to counteract the chromatic dispersion from a long span of transmission fiber. It is a packaged unit with fiber connectors, allowing for easy insertion into a fiber-optic link.

What technologies are used to make dispersion compensation modules?

Common technologies for DCMs include long spools of dispersion-compensating fiber, chirped fiber Bragg gratings, and virtually imaged phased arrays for wavelength division multiplexing (WDM) systems.

Why is the insertion loss of a DCM a concern?

The insertion loss of a DCM must be overcome by a fiber amplifier. Lower losses are desirable because they reduce the required amplifier gain and the associated excess noise added to the signal.

What is the importance of the dispersion slope for a DCM?

The dispersion slope (higher-order dispersion) is critical for WDM systems, where multiple wavelength channels must be compensated simultaneously. The DCM's slope must be properly matched to that of the transmission fiber to ensure good performance across the entire bandwidth.

Can the dispersion from a DCM be adjusted?

Yes, tunable dispersion modules are available. For example, in DCMs based on fiber Bragg gratings, the dispersion can be tuned by varying the device temperature, often using built-in temperature gradients.

Questions and Comments from Users

Here you can submit questions and comments. As far as they get accepted by the author, they will appear above this paragraph together with the author’s answer. The author will decide on acceptance based on certain criteria. Essentially, the issue must be of sufficiently broad interest.

Please do not enter personal data here. (See also our privacy declaration.) If you wish to receive personal feedback or consultancy from the author, please contact him, e.g. via e-mail.

By submitting the information, you give your consent to the potential publication of your inputs on our website according to our rules. (If you later retract your consent, we will delete those inputs.) As your inputs are first reviewed by the author, they may be published with some delay.