large mode area fibers (original) (raw)

Acronym: LMA fiber

Definition: optical fibers with relatively large mode areas and a single transverse mode or only a few modes

Category: fiber optics and waveguides

• fiber optics
  • fibers
    * passive fibers
    * active fibers
    * step-index fibers
    * graded-index fibers
    * polarization-maintaining fibers
    * photonic crystal fibers
    * photonic bandgap fibers
    * hollow-core fibers
    * multi-core fibers
    * nanofibers
    * single-mode fibers
    * single-polarization fibers
    * few-mode fibers
    * multimode fibers
    * large-core fibers
    * large mode area fibers
    * tapered fibers
    * mid-infrared fibers
    * dispersion-engineered fibers
    * telecom fibers
    * silica fibers
    * fluoride fibers
    * single-crystal fibers
    * plastic optical fibers
    * specialty fibers
    * (more topics)

Related: large-core fiberseffective mode areadouble-clad fibersbend lossesnumerical aperturefiber coreleaky modesfiber amplifiersphotonic crystal fibersSingle-Mode Fibers with Large Mode AreasHigher-Order Modes of Fibers: a Solution for Single-Mode Guidance with Large Mode Area?Diffraction in Optical FibersDiffraction in Optical FibersContinuing Struggle for Larger Fiber Mode AreasEasier Launching into Fibers with Large Mode Area?

Page views in 12 months: 1933

DOI: 10.61835/xrf Cite the article: BibTex BibLaTex plain textHTML Link to this page! LinkedIn

Content quality and neutrality are maintained according to our editorial policy.

📦 For purchasing large mode area fibers, use the RP Photonics Buyer's Guide — an expert-curated directory for finding all relevant suppliers, which also offers advanced purchasing assistance.

Contents

What are Large Mode Area Fibers?

For some applications, it is desirable to use optical fibers with particularly large effective mode areas (LMA fibers) — but often still with single-mode guidance, or at most with few modes. In many cases, such fibers are double-clad fibers, as these are often needed for applications involving high power levels.

For a given optical power, large mode areas imply reduced optical intensities. Therefore, such fibers effectively exhibit weaker nonlinear optical effects and a higher damage threshold. That makes them suitable for, e.g., the amplification of intense pulses or single-frequency signals in fiber amplifiers, or in the case of passive fibers for delivery of such light. Whereas standard single-mode fibers have an effective mode area below 100 μm2, large mode area fibers reach values of hundreds or even thousands of μm2.

For a large mode area, one requires a large fiber core. However, large-core fibers do not necessarily have large modes, if they are strongly multimode; at least the fundamental mode may then be much smaller than the core.

Note that waveguide dispersion becomes weak for large mode areas. Therefore, there is limited scope for tailoring the chromatic dispersion of large mode area fibers.

Figure 1: Comparison of bare (uncoated) fibers with a standard core size (e.g. 8 μm diameter) and a large core (50 μm diameter).

Design Approaches and Limiting Factors

A straightforward design approach to obtain large mode areas is to decrease the numerical aperture (NA), i.e., to decrease the refractive index difference between the core and the cladding, for a step-index fiber design (see Figure 2). However, there are severe limitations: the guidance (waveguiding) then becomes weak, and significant losses can arise from small imperfections of the fiber or from bending (→ bend losses). Therefore, the numerical aperture should normally not be made smaller than approximately 0.06, although in extreme cases values as low as 0.04 have been used [39].

Figure 2: Effective mode area of a step-index fiber as a function of numerical aperture (NA) for different values of the V-number.

Large mode areas can in principle be achieved even with ($V$) = 2, i.e., with strictly single-mode guidance, but this requires the use of a very small numerical aperture, which implies a critical dependence on refractive index inhomogeneities and bending.

There are additional difficulties in applying this concept to rare-earth-doped fibers. Relatively high concentrations of additional dopants like alumina or phosphorus are often required, e.g. for reducing certain quenching effects, and these dopants often increase the numerical aperture. Even if the refractive index contrast can be reduced in some way, e.g. by also somewhat raising the refractive index around the core, the precision of refractive index control may be decreased, and this affects the ability to realize very large mode areas. Also, in high-power fiber lasers and amplifiers based on large mode area fibers, thermal lensing can lead to changes in mode properties, in particular to a reduction in effective mode area [32].

Somewhat larger mode areas can be achieved with fiber designs supporting a few propagation modes (→ few-mode fibers). It may then still be possible to guide light dominantly in the fundamental mode, so that the output e.g. of a fiber amplifier is close to diffraction-limited [2, 3, 6]. Stringent limitations arise from the more critical launch conditions and from mode mixing in the fiber, which can spoil the beam quality and lead to beam pointing fluctuations [17].

Various more sophisticated fiber designs (partly based on photonic crystal fibers) and techniques have been developed for addressing these challenges. In many cases, one attempts to introduce substantial propagation losses for any higher-order modes, making it easier to maintain robust single-mode propagation in a multimode fiber. Another important aspect is to minimize unwanted mode coupling, basically by achieving a large enough difference in the propagation constants between the fundamental and higher-order modes.

Some examples of possible design strategies of large mode areas are:

• One may strongly bend the fiber; depending on the fiber design, the induced bend losses may be substantial for higher-order modes at a point where they are not yet significant for the fundamental mode. Fiber designs can be optimized in that respect. Note that bending not only introduces losses, but also can reduce the effective mode area. This is particularly true for large mode area step-index fibers. For a fair comparison of fiber types, this effect definitely has to be taken into account [9]. It turns out that some fiber designs have a large mode area without bending, but a much reduced mode area with bending, whereas there are other designs (e.g. with a parabolic index profile) where the mode area starts with a somewhat smaller value but is much less sensitive to bending.
• So-called chirally coupled core fibers [13, 22, 34] have a straight central core in which the signal propagates, plus another core which is helically wound around the central core. It is possible to obtain strongly selective coupling of the helical core only to higher-order modes of the central core, while leaving the fundamental mode essentially unaffected. The principle of this selective coupling is that the helicity affects the propagation constant in such a way that at least in some limited wavelength range phase matching occurs only for coupling to higher-order modes but not to the fundamental mode.
• Other fiber designs work with other kinds of shunt cores, to which unwanted higher-order guided modes are resonantly coupled if they have a similar effective refractive index.
• In leakage channel fibers [8, 12], the core is surrounded by a small number of large holes, making all propagation modes leaky in a very selective way, such that all higher-order modes but not the fundamental mode experience substantial propagation losses. While earlier versions of such fibers have been made as photonic crystal fibers with air holes, solid all-glass designs are also possible [24].
• Pixelated Bragg fibers are modified versions of so-called Bragg fibers, i.e., fibers with a sequence of high-index rings fulfilling a half-wave stack condition. Here, the high-index rings are made discontinuous (pixelated) such that the propagation losses become high for higher-order modes while remaining low for the fundamental mode [36, 38]. Such fibers can be fabricated with stack-and-draw techniques.
• The problem of refractive index control can in some situations be mitigated by using a multifilament core, where the fiber core is realized as a two-dimensional array of filaments [20]. As each single filament exhibits only weak guidance, the overall structure can exhibit single-mode guidance. This concept is particularly interesting for erbium-ytterbium-doped fibers.
• A relatively novel concept is that of the gain-guided, index-antiguided single-mode fiber [7, 15, 23, 27], which is a type of active fiber. Here, the unpumped fiber is not guiding (even antiguiding), as the refractive index of its core is lower than that of the cladding. For sufficiently strong pumping, however, gain guiding can stabilize a leaky mode with high beam quality. As the losses of such a mode rapidly decrease for increasing core size, a fairly moderate laser gain can be sufficient to achieve propagation with positive net gain if the core is large. Higher-order modes also exist, but would require a significantly higher gain. That level of gain is not reached when the lower-order mode saturates the gain, as it easily happens in a laser, but not necessarily in a high-gain amplifier. The greatest challenge of this concept is efficient pumping. Note that the pump light is not guided and even expelled from the doped core by the index structure and the absorption. A diode-pumped fiber laser has been demonstrated with this concept [23], but novel pump arrangements will have to be developed to allow for efficient operation.

The best fiber designs reach an effective mode area of several thousand μm2. There is no strict limit, but designs with larger mode areas exhibit less robust single-mode propagation and often can tolerate only very slight bending. It appears that no kind of design can offer a further substantial expansion of the mode area with robust single-mode propagation. The reason for this is essentially that a mode involves some balance of diffraction and waveguiding, and as diffraction inevitably becomes weaker at larger mode areas, this balance becomes more and more sensitive to any disturbances.

For high-power operation, significant thermo-optic problems can occur in large mode area fibers. In particular, the effective mode area may shrink due to thermal lensing, and additional spatial modes may be supported.

Difficulties with Interfacing

A general problem with the use of large mode are fibers is that these fibers are not compatible with standard fiber components. (Many fiber-optic components are only available with standard mode sizes.) When a large mode area fiber is spliced to a standard fiber, the large mismatch in mode areas leads to an excessive power loss at the joint (see the article on fiber joints). There are two solutions to this problem, which however are both not fully satisfying:

• One can use a tapered fiber as a mode converter between the two fibers. The tapered fiber must be made such that the mode size matches that of the large mode area fiber on one end and that of the standard fiber on the other hand. One then has to do two splices instead of one, but each one can have very low losses. The main difficulty with that method is that a tapered fiber is needed, which may not be easy to obtain.
• A frequently used solution for laboratory experiments is to use free-space coupling from and to the large mode area fiber. A laser resonator may then be made with bulk components only, apart from the active fiber. This leads to flexible laboratory setups, which however are not very suitable for commercial use, as they involve sensitive alignment and are sensitive to dust, particularly to dust deposited on the fiber endfaces.

Alternative Solution: Using Higher-order Modes

Normally, a large mode area fiber is understood to be a fiber which has a single guided mode per polarization direction or only very few modes. However, one can also obtain a large mode area by utilizing a high-order mode of a multimode fiber [11, 21, 35]. In practice, one can first couple light from the fundamental mode to a particular higher-order mode, using a long-period fiber Bragg grating. Thereafter, light can propagate in that mode e.g. in an amplifying fiber, and finally it can be converted back to the fundamental mode with another fiber Bragg grating.

The advantage of using a higher-order mode is twofold: such modes have larger effective mode areas, and they exhibit a weaker coupling to other modes. The power losses associated with coupling to and from this higher-order mode can be small, and the fiber design can be optimized for a broad bandwidth for this coupling.

However, difficulties with that HOM fiber technique might arise from the very uneven intensity distribution. This can lead to fiber damage even in a regime where the overall nonlinearity is moderately strong, so the approach may solve problems with nonlinearities but not those with damage. Also, the mode field significantly extends into the cladding (the inner cladding in the case of a double-clad fiber), which is not ideal for amplification.

Frequently Asked Questions

What is a large mode area (LMA) fiber?

A large mode area (LMA) fiber is an optical fiber designed to have a particularly large effective mode area, often in the hundreds or thousands of μm2, while maintaining single-mode or few-mode guidance.

Why are large mode areas in fibers often desirable?

A large mode area reduces the optical intensity for a given power level. This mitigates unwanted nonlinear optical effects and increases the damage threshold, which is crucial for high-power fiber amplifiers and delivering intense light pulses.

What is the simplest way to design an LMA fiber, and what is its limitation?

The most straightforward approach for a step-index fiber is to use a large fiber core and a small numerical aperture (NA). The main limitation is that a very small NA leads to weak light guidance, making the fiber highly sensitive to bend losses and imperfections.

How can robust single-mode operation be achieved in a large mode area fiber?

Various advanced designs introduce high propagation losses for higher-order modes while keeping losses low for the fundamental mode. Examples include leakage channel fibers, chirally coupled core fibers, and careful bending of the fiber.

What are the challenges when connecting LMA fibers to standard optical fibers?

Splicing an LMA fiber to a standard fiber results in a large mode area mismatch, causing significant power loss at the joint. This can be addressed by using a tapered mode converter or by using free-space optical coupling.

What are the challenges with rare-earth-doped LMA fibers?

Is it possible to use higher-order modes to get a large effective area?

Yes, one can use a higher-order mode (HOM) of a multimode fiber, which can have a very large area. Special components like long-period fiber Bragg gratings are needed to couple light into and out of the desired HOM.

Suppliers

Sponsored content: The RP Photonics Buyer's Guide contains eight suppliers for large mode area fibers. Among them:

⚙ hardware

Exail (formerly iXblue) offers a wide range of specialty optical fibers for lasers and amplifiers. We master erbium, erbium/ytterbium, ytterbium, thulium, holmium, thulium/holmium, neodymium, dysprosium, and phosphorous gain media. PM version are available, and Large Mode Area (LMA) or Very Large Mode Area (VLMA) versions as well. Depending of the requirement, single clad fibers are available for core pumping, double clad fibers for clad pumping. Triple clad and all glass structures are also available.

⚙ hardware

Our large mode area photonic crystal fibers are designed for diffraction-limited high-power delivery. The large mode area prevents nonlinear effects and material damage. With standard fibers, you trade large mode areas for single-mode operation. With our large mode area fibers, you get single-mode operation in a wide range of wavelengths. Also available in a polarization-maintaining version.

Bibliography

(Suggest additional literature!)

Questions and Comments from Users

Here you can submit questions and comments. As far as they get accepted by the author, they will appear above this paragraph together with the author’s answer. The author will decide on acceptance based on certain criteria. Essentially, the issue must be of sufficiently broad interest.

Please do not enter personal data here. (See also our privacy declaration.) If you wish to receive personal feedback or consultancy from the author, please contact him, e.g. via e-mail.

By submitting the information, you give your consent to the potential publication of your inputs on our website according to our rules. (If you later retract your consent, we will delete those inputs.) As your inputs are first reviewed by the author, they may be published with some delay.