fiber core (original) (raw)

Author: the photonics expert (RP)

Definition: the region in an optical fiber which guides light

Category: article belongs to category fiber optics and waveguides fiber optics and waveguides

Related: Tutorial on Passive Fiber Opticsfibersrare-earth-doped fibersdouble-clad fibersphotonic bandgap fibershollow-core fibersdoping concentration

Page views in 12 months: 949

DOI: 10.61835/748 Cite the article: BibTex BibLaTex plain textHTML Link to this page! LinkedIn

Content quality and neutrality are maintained according to our editorial policy.

Contents

What is a Fiber Core?

The core of a fiber is the region in which the light is guided, i.e., it is primarily responsible for the waveguiding effect. (The articles on fibers and waveguides explain more about the guiding properties.) In the case of active fibers, it also provides amplification of light.

The article focuses on cores for glass fibers, although there are also plastic optical fibers.

Refractive Index Control

core of single-mode and multimode fiber

Figure 1: A single-mode fiber has a core which is very small compared with the cladding, whereas a multimode fiber can have a large core.

The waveguiding properties are determined by the refractive index profile, i.e., the increase in refractive index in the core relative to that of the cladding. For step-index profiles, the numerical aperture and the V-number are frequently used parameters. Many fibers, however, are based on non-step-index designs, where those parameters are not well defined and thus of limited utility. For example, there are graded-index fibers with an approximately parabolic index profile, and single-mode fibers with a pronounced fabrication-related index dip at the center.

Usually, the core is a region of slightly increased refractive index, obtained not by using an entirely different glass, but by doping the glass with some index-raising material. In the case of silica fibers, typical index-raising dopants are

Alternatively or in addition, the index of the fiber cladding (or only of a limited trench around the core) may be lowered e.g. by fluorine doping. Index-lowering agents can also be used in the core if other required dopants (particularly for active fibers, see below) would make the refractive index difference too high. Alternatively, one may then produce a ring with slightly increased refractive index around the core.

Particularly for large mode area single-mode fibers with low numerical aperture, the exact refractive index profile can be important. For example, the frequently encountered effect that the center of the core exhibits a dip in the refractive index can be detrimental.

In conventional all-glass fibers, one usually has only a quite limited refractive index contrast, and the guided modes can be calculated using the scalar approximation, which very much simplifies the mathematical analysis.

In photonic crystal fibers, however, the waveguide function can be realized in different ways:

Typically, the waveguiding in photonic crystal fibers is not achieved with index-raising or index-lowering dopants, but essentially by a proper placement of tiny air holes.

Tutorials

Tutorial on Passive Fiber Optics

Passive Fiber Optics

This is a comprehensive introduction to fiber optics, focusing on passive (non-amplifying) fibers. It explains basic principles as well as practical aspects.

Hollow-core Fibers

Photonic crystal fibers can even have a hollow core, i.e., an air hole with a diameter of typically a few microns. Waveguiding is then achieved with a kind of photonic bandgap. See the article on hollow-core fibers for details.

Cores for Active Fibers

Additional laser-active dopants are required for active fibers, i.e., for fibers which can be used for fiber amplifiers or lasers. In almost all cases, the fiber core contains rare earth ions such as Er3+ (erbium), Yb3+ (ytterbium) or Nd3+ (neodymium) — and normally some additional dopants, for example for improving the solubility of the rare earth ions, which is quite low for pure fused silica. One often uses aluminosilicate or phosphosilicate glasses.

The maximum phonon energy of the core glass material determines the potential for multi-phonon transitions and thus can have a strong influence on the lifetime of energy levels.

The glass composition also influences the possibility of efficient energy transfer between different ions, e.g. in erbium-ytterbium-doped fibers.

For details, see the article on rare-earth-doped fibers.

Birefringent Fibers

Although the fiber core is rotationally symmetrical for most fibers, there are methods to break this symmetry e.g. by using an elliptical core and/or by introducing asymmetric structures around the core. This can lead to strong birefringence (→ polarization-maintaining fibers) and even to polarization-dependent guidance (→ single-polarization fibers).

Various Relevant Fiber Core Properties

In addition to the waveguiding, the details of the core also influence other properties of a fiber:

Non-centered Fiber Cores

In most cases, the fiber core is located at the center of the fiber's cross-section because this facilitates splicing, launching light, the use of fiber connectors and other fiber joints, etc. However, for double-clad fibers it can be advantageous to use an off-centered core because this can substantially improve the pump absorption. In rare cases, helical core fibers are used where the core winds around the fiber axis.

There are also multi-core fibers, containing multiple cores, where obviously at most one of those can be centered on the fiber cross-section.

Frequently Asked Questions

What is the core of an optical fiber?

The core is the central region of an optical fiber that guides light. This waveguiding effect is typically achieved because the core has a higher refractive index than the surrounding fiber cladding.

How is the refractive index of a fiber core controlled?

The core's refractive index is usually increased by doping the host glass (e.g., silica) with index-raising materials like germania (GeO2) or alumina (Al2O3).

What makes a fiber core 'active'?

An active fiber core is doped with rare earth ions, such as erbium or ytterbium. This enables the fiber to amplify light and function as a gain medium in a fiber amplifier or fiber laser.

What defines a step-index fiber core?

A step-index fiber has a core with a uniform refractive index that is slightly higher than that of the surrounding cladding. This creates a sharp, step-like change in the refractive index profile at the core-cladding boundary.

Can a fiber core be hollow?

Why are some fiber cores deliberately placed off-center?

In double-clad fibers, an off-centered core can substantially improve pump absorption by increasing its overlap with the pump light in the inner cladding. Multi-core fibers also inherently contain off-center cores.

Questions and Comments from Users

Here you can submit questions and comments. As far as they get accepted by the author, they will appear above this paragraph together with the author’s answer. The author will decide on acceptance based on certain criteria. Essentially, the issue must be of sufficiently broad interest.

Please do not enter personal data here. (See also our privacy declaration.) If you wish to receive personal feedback or consultancy from the author, please contact him, e.g. via e-mail.

By submitting the information, you give your consent to the potential publication of your inputs on our website according to our rules. (If you later retract your consent, we will delete those inputs.) As your inputs are first reviewed by the author, they may be published with some delay.