fusion splicing of fibers (original) (raw)

Definition: a technique of making low-loss fiber joints by fusing fiber ends together

Category: fiber optics and waveguides

• fiber optics
  • fiber splices
    * fusion splicing of fibers
    * mechanical fiber splices

Related: Tutorial on Passive Fiber Optics Part 13: Fiber Accessories and Toolsfiber splicesfibersfiber jointscleaving of fibersfiber endface inspection

Page views in 12 months: 891

DOI: 10.61835/mgj Cite the article: BibTex BibLaTex plain textHTML Link to this page! LinkedIn

Content quality and neutrality are maintained according to our editorial policy.

📦 For purchasing fusion splicers, use the RP Photonics Buyer's Guide — an expert-curated directory for finding all relevant suppliers, which also offers advanced purchasing assistance.

Contents

Principle of Fusion Splicing of Fibers

The principle of fusion splicing is a common method of making fiber splices. It involves fusing the two bare fiber ends (with coatings removed) under the influence of heat. More precisely, the fiber ends are initially brought in close contact, with a small gap in between. After heating them for a short while such that the surfaces melt, they are pushed together, such that the ends fuse together.

The heating is often accomplished with a high-voltage electric discharge, but there are other methods: an electrically heated nickel-chromium wire, a CO2 laser (for a kind of laser welding), or a gas flame.

Surface tension helps to achieve a good alignment, if the fiber cores are on the fiber axes. It is also possible to precisely align the fibers before the splicing such that the cores (even when they are slightly off-center) match well, but there is a risk that surface tension will pull the fiber ends toward a position where the total areas (rather than the cores) are matched.

Splicing of multimode fibers is rather uncritical. Here, substantial transition losses are to be expected only when the fiber parameters are not well matched, e.g., if the core areas are rather different. For single-mode fibers, the process is more critical. Here, the ideal conditions for reliable low-loss splices are:

• The fibers are silica fibers. Not all other glass materials are suitable for fusion splicing.
• The parameters of the fusion splicer (in particular, the electric current and duration of the arc) are well optimized for the given fiber type (material and diameter).
• The fibers have equal cladding diameters.
• The fiber coating is fully removed with a fiber stripper.
• The fiber ends are well prepared, with exactly perpendicular cuts, no surface irregularities and no dust. A carefully done fiber cleave (done with some fiber cleaver device) should normally be good enough. Polishing leads to the highest surface quality and angular accuracy, but is more time-consuming.
• The fiber cores are exactly on the fiber axes, and the alignment is precise. (It is often observed under a microscope.) See also the article on fiber endface inspection.
• The effective mode areas are the same and not too small.
• There are no detrimental effects through a broadening of the fiber core by diffusion during the time when the fiber ends are hot. In some cases, diffusion can even be helpful, e.g. when splicing erbium-doped fibers with small mode area to passive fibers, where diffusion can create a kind of mode field adapter.

Under ideal conditions, fusion splices quite reliably exhibit very low transition losses of the order of 0.02 dB. Nearly no light will be reflected at the splice. The splice location can then hardly be seen under a microscope. Nevertheless, the mechanical strength of the splice and its surroundings may be well below that of the normal bare fiber, if the fiber surface receives some damage during handling; very small scratches are sufficient for that effect. Note that the protective coating has to be removed for splicing, and that this removal process carries a risk of damaging the fiber surface. After splicing, it is common to apply a new coating or attach some other protective material (e.g., a heat shrink protector or a mechanical crimp protector) to obtain a sufficiently high mechanical robustness.

Low-loss splices may also be achieved under non-ideal conditions, e.g. for fibers with different diameters. When the fiber cores are not centered, it may be necessary to do the alignment while monitoring the throughput of light. In such cases, however, the splicing process may be less reliable and needs more care. A substantial fraction of the splices may have to be redone until a satisfactory result is achieved.

Note that the stripped fiber is less robust and therefore often needs some extra protection. After fusion splicing, one often uses a splice protection sleeve to protect the spliced region. Another possibility is to use a fiber recoater.

Features of Fusion Splicers

An apparatus suitable for high-quality fusion splices will usually have the following features:

• Carefully engineered fiber clamps allow the precise fixing of the fiber ends. At least one clamp is precisely adjustable with micrometer screws.
• For splicing polarization-maintaining fibers or multi-core fibers, it is also necessary to rotate one of the fibers around its axis.
• A fiber microscope allows inspection of quality and alignment of the fiber ends. Often, there is a knob for switching between two orthogonal directions of view. The fiber cores can also usually be seen.
• A “prefuse”, applied without touching the fibers, allows one to clean the surfaces.

Some special features:

• Some splicers do the alignment automatically based on a camera image and/or on monitoring the optical power throughput. For the latter, there must be a light source attached to one fiber end, and a photodetector for the other one.
• Some devices can also measure the quality of the resulting splice.
• While some fusion splicers are specialized for standard telecom fibers, others can be used for a wider range of fibers, e.g. with smaller or larger cladding diameters. For example, there are swing-electrode based fusion techniques which are suitable for large cladding fibers.
• Some devices simply offer a higher accuracy, as required e.g. for splicing fibers for space division multiplexing.

Testing Fusion Splices

A first test of a splice is the inspection with the microscope of the splicer apparatus. Normally, one should hardly be able to see the splice. Nevertheless, there may be a problem e.g. resulting from an offset of the fiber cores.

When visible light is launched into the fiber, a lot of stray light can result at a faulty splice, which is thus easy to recognize, although that does not deliver a quantitative measure of the splice quality.

A precise measurement of a splice loss is helpful, but not easy. That starts with the challenge of launching a precisely known amount of optical power into the fiber, and continues with measuring the output power with a precision of 0.1 dB, for example.

Optical time-domain reflectometry (OTDR) is often used for checking fiber cables including splices. At least serious faults are easily recognized and located with that technique. However, this requires an expensive OTDR apparatus.

Advantages and Limitations of Fusion Splicing

In comparison with other techniques for making fiber joints, fusion splicing has some substantial advantages:

• No other method promises lower transition losses and weaker reflections.
• The resulting joints are very stable, i.e., no alignment needs to be maintained, and no dust can affect the joint.
• No parts or materials are required, except for protecting the fiber after splicing.

Some non-ideal aspects of fusion splicing are:

• An apparatus for fusion splicing is fairly expensive, and its use requires adequate training.
• Compared to equipment for mechanical splices, for example, it is more difficult to use in the field, as it is less compact and requires electricity.
• Connections are not easy to remove. Essentially, a new cleave would be required, possibly followed by surface preparation.

Note also that in high-power fiber lasers and amplifiers the power of light lost in splices can be sufficient for burning materials, in particular fiber coatings. This means that high-quality splices are essential not only for the power efficiency, but also for reliable operation.

The use of fusion splices is common for outdoor fiber cables; long cables are usually made by fusion-splicing fiber cables together, each one having a length of a few kilometers. For indoor transmission cables, one usually uses mechanical splices or fiber connectors, avoiding the use of expensive fusion splicers. Fusion splicing is also used in factories for making stable fiber-optic devices such as fiber lasers and amplifiers.

Frequently Asked Questions

This FAQ section was generated with AI based on the article content and has been reviewed by the article’s author (RP).

What is fusion splicing of optical fibers?

Fusion splicing is a method for creating a permanent joint between two optical fibers. It involves heating the bare fiber ends until they melt and then pushing them together to fuse, forming a single, continuous fiber.

How are fibers heated during fusion splicing?

The most common heating method is a high-voltage electric discharge, also known as an electric arc. Other techniques include using a heated nichrome wire, a CO2 laser, or a gas flame.

What is required for a good low-loss fusion splice?

A low-loss splice requires that the fiber ends are perfectly clean and well-cleaved. The fibers should have matching parameters, like cladding diameter and mode area, and their cores must be precisely aligned before being fused.

What are the main advantages of fusion splicing?

Fusion splicing provides the lowest possible splice loss and weakest reflections compared to other methods. The resulting joints are extremely stable and robust because the fiber is permanently fused and sealed from dust.

What are the disadvantages to fusion splicing?

Fusion splicers are expensive pieces of equipment requiring trained operators. They are also less portable and require electricity, making them harder to use in the field than tools for mechanical splices.

Why can a fusion splice be mechanically weak?

For splicing, the fiber's protective coating must be stripped off, exposing the glass surface. Any microscopic scratches introduced during handling can significantly reduce the mechanical strength of the spliced region.

How is the quality of a fusion splice tested?

Splices can be visually inspected with the splicer's microscope. For a quantitative measurement, the splice loss can be determined by monitoring the optical power throughput or by using an optical time-domain reflectometer (OTDR).

Suppliers

Bibliography

(Suggest additional literature!)

Questions and Comments from Users

Here you can submit questions and comments. As far as they get accepted by the author, they will appear above this paragraph together with the author’s answer. The author will decide on acceptance based on certain criteria. Essentially, the issue must be of sufficiently broad interest.

Please do not enter personal data here. (See also our privacy declaration.) If you wish to receive personal feedback or consultancy from the author, please contact him, e.g. via e-mail.

By submitting the information, you give your consent to the potential publication of your inputs on our website according to our rules. (If you later retract your consent, we will delete those inputs.) As your inputs are first reviewed by the author, they may be published with some delay.